Habilitations/ doctoral thesis/ trade press

2024

2023

WoMag 2023

2021

  • Jahrbuch Oberflächentechnik Band 77 (2021): David Glück, Mathias Fritz, Indira Käpplinger, Andreas Bund, "Nickel-Ti3SiC2-Dispersionsbeschictungen", Eugen G. Leuze Verlag KG, Bad Saulgau, ISBN 978-3-87480-369-4, pp. 117-125

2019

  • DGM-dIALOG Vol 3(2019) S16-21
    "Elektrochemische Oberflächentechnik"
    R. Böttcher, A. Endrikat, T. Engemann, M. Fritz, V. Gruia, S. Hesamedini, A. Ispas, M. Leimbach, U. Schmidt, R. Sottor und A. Bund

Publications of the "Electrochemistry and Electroplating" group

Results: 586
Created on: Thu, 28 Mar 2024 23:02:07 +0100 in 3.2568 sec


Omar, Nurul Amanina Binti; Köster, Frank; Hahn, Frank; Bund, Andreas
Hardness and tribological behaviour of annealed electroless nickel phosphorus composite layers with incorporated boron particles. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 476 (2024), 130261, S. 1-17

In this study, a possible alternative to hard chromium coatings is investigated. Amorphous boron particles have been incorporated in electroless nickel‑phosphorus (NiP) deposits, yielding a dispersion coating. The distribution of the particles is homogenous and the maximum mass fraction of particles embedded in the coating is 6.2 ± 0.2 wt%. Measurements of the zeta potential and particle size of amorphous boron particles in a diluted electrolyte showed that the particles withstood agglomeration until 120 days. Primary and secondary hardness maxima are observed after thermal annealing at 400 ˚C and 860 ˚C due to the formation of nickel phosphide, nickel boride and nickel boride phosphide phases. X-ray diffractometry shows an increase in nickel and nickel phosphide crystal size at 400 ˚C before levelling off at 600 ˚C. The annealing duration should be kept between 30 and 60 min for optimal hardness. The wear resistance increases when the coating is annealed at 400 ˚C. DSC measurements on nickel phosphorus incorporated with boron particles, Ni-P-B, bulk material with P-content (9.6 ± 0,6 wt%) and B-content (4.5 ± 0.8 wt%) showed that the solidus line lies at 926 ˚C, which is why a maximum annealing temperature of 860 ˚C was chosen to avoid melting of the material. The relative texture and phase coefficients, RTC and RPC, showed that the nickel phase is preferred in the NiP system at 400 ˚C and 600 ˚C while the Ni3P phase is preferred in the Ni-P-B system at the same annealing temperature. REM and EDX area analyses are used to show the areal distribution of nickel, phosphorus, and boron before and after the annealing process along the thickness of the coating. A diffusion layer between substrate and coating that contains iron nickel boride and iron nickel phosphide lamellar structure is observed.



https://doi.org/10.1016/j.surfcoat.2023.130261
Supreeti, Shraddha; Fischer, Michael; Fritz, Mathias; Müller, Jens
High-resolution patterning on LTCC by transfer of photolithography-based metallic microstructures. - In: International journal of applied ceramic technology, ISSN 1744-7402, Bd. 21 (2024), 2, S. 1180-1190

The growing applications and constant miniaturization of electronic devices and of low-temperature co-fired ceramics (LTCC) in various fields, such as aviation, telecommunications, automotive, satellite communications, and military, have led to an increase in the demand for LTCC. Such prospects arise due to the continuous scaling down of components and high-density interconnection in electronics packaging. This paper reports a technique for the transfer of high-resolution microstructures from silicon substrates to LTCC. In this method, gold and copper patterns were formed by photolithography, electrodeposition, and residual layer stripping on silicon substrate. Lithography provides the opportunity to create and transfer complex patterns for use in several different applications and electroplating enables the use of pure metal for excellent electrical properties. The developed structures were transferred onto a top layer of LTCC tape using hot embossing. Then, the subsequent layers were stacked, laminated, and sintered. A resolution of 1.5 μm after free sintering and 4.5 μm after pressure-assisted sintering was achieved. This distinctive method can be useful for several applications requiring high-resolution and superior electrical properties.



https://doi.org/10.1111/ijac.14569
Najeeb, Mussab; Schwalbe, Ulf; Herget, Mathias
Improved approach for online monitoring of second life lithium-ion batteries to optimize the performance in stationary storage systems. - In: IEEE Xplore digital library, ISSN 2473-2001, (2023), insges. 6 S.

Monitoring lithium-ion batteries in their second life is of great importance when using them in stationary storage systems for grid support or in any other energy system, due to the expected different behavior and operational conditions in their second life compared to their first life. The idea of this study based on the fact that each estimation method has its advantages and drawbacks depending on the application in which the batteries will be used, and that monitoring batteries in their second life required to be integrated with the battery management system to balance cells, optimize performance, and prevent overheating. The contribution of our study can be summarized in the integration of specific methods, aiming to benefit from most of their advantages and neutralizing their drawbacks as much as possible to provide more accurate and reliable online monitoring of batteries. The combination presented in this study, consisting, for state of charge estimation, of an artificial neural network and an Unscented Kalman Filter with adjusting the filtering process using Coulomb counting, and Kalman Filter for state of health estimation, showed much better reliability and accuracy than if each method was used alone. This combination has been trained and adjusted using empirical data of second-life batteries, extracted from used electric vehicle battery bank, to obtain the best possible performance, considering the specificity of these batteries in terms of operating voltage range, lower current ratio, and other parameters.



https://doi.org/10.1109/IREC59750.2023.10389283
Kurniawan, Mario; Bund, Andreas
Photoelectrochemical water splitting with cuprous oxide. - In: Galvanotechnik, ISSN 0016-4232, Bd. 114 (2023), 11, S. 1396-1398

Enhancing the performance through the implementation of porous structures - an innovative and cost-effective fabrication technique that relies solely on electrodeposition.



Engemann, Thomas; Ispas, Adriana; Bund, Andreas
Electrochemical reduction of tantalum and titanium halides in 1-butyl-1-methylpyrrolidinium bis (trifluoromethyl-sulfonyl)imide and 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate ionic liquids. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 0 (2023), 0, insges. 14 S.

The electrodeposition of tantalum-titanium–based films using different tantalum and titanium halides was investigated in two ionic liquids, namely, 1-butyl-1-methylpyrrolidinium bis (trifluoromethyl-sulfonyl)imide ([BMP][TFSI]) and 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate ([BMP][OTf]). Cyclic voltammetry was used to analyse the electrochemistry of the electrolytes and potentiostatic deposition was performed to evaluate the feasibility of electrodepositing tantalum-titanium–based layers. Both the metal salts and the ionic liquid influenced the electrochemical reduction of the tantalum and titanium halides significantly. While titanium halides considerably retarded the reduction of tantalum pentahalides and inhibited electrodeposition in many electrolytes, an electrolyte composition from which tantalum and titanium-containing layers could be deposited was identified. Specifically, in TaBr5 and TiBr4 in [BMP][TFSI], TiBr4 did not inhibit the deposition of tantalum and titanium was co-deposited itself by a three-step reduction mechanism as confirmed by cyclic voltammetry and energy-dispersive X-ray spectroscopy. Furthermore, [BMP][TFSI] led to smoother and more compact deposits.



https://doi.org/10.1007/s10008-023-05773-7
Witt, Michael; Papmahl, Eric; Genov, Ivan; Dimitrova, Anna; Gabryelczyk, Agnieszka; Krischok, Stefan; Lota, Grzegorz; Ivanov, Svetlozar
In-situ electrogravimetric detection of the cathodic process during the galvanic coupling between lithium and copper. - In: Electrochimica acta, ISSN 1873-3859, Bd. 463 (2023), 142853

With the development of the energy system transformation the quality and efficiency of the rechargeable batteries, particularly the Li ion technology, gain major importance. In spite of the enormous advances, along with many other technological challenges corrosion of the metallic battery parts is often a difficult obstacle for producers and researchers. Li-metal batteries and especially the “anode-free” battery concept could significantly increase the energy density. However, contact corrosion of the Li anode, can occur in this cell configuration since there is a high probability of a three-phase contact between Li-metal, current collector and electrolyte, a condition triggering an intensive Li corrosion. In this work, a new in-situ analytical methodology based on combining electrochemical (ZRA) and microgravimetric (QCM) techniques is proposed for studying the galvanic corrosion. The applicability of this approach is explored in three different electrolyte compositions. Beside the analysis of the conventional electrochemical parameters an in-situ gravimetric detection of the deposited electrolyte decomposition products on the cathode surface is demonstrated. Adsorbed polymer layer on the Cu surface is applied for cathodic inhibition of the galvanic corrosion process, which is studied by means of the novel ZRA-QCM approach.



https://doi.org/10.1016/j.electacta.2023.142853
Moazezi, Alireza; Henne, Stefan Georg; Fritz, Mathias
Improvement of corrosion behavior of chromium(III) coatings. - In: Galvanotechnik, ISSN 0016-4232, Bd. 114 (2023), 3, S. 311-319

Nickel/Chromium electroplating is widely used in engineering applications, especially for decorative thin film plating, abrasion resistance, and corrosion protection [1]. Depositions of metallic chromium from trivalent chromium electrolytes show a lower corrosion resistance than those from hexavalent baths. Therefore, this research work investigated the effect of anodic post-treatment on the corrosion behavior of conventional and micro-cracked chromium (III) based coatings with a series of evaluation methods for corrosion resistance. While the corrosion tests indicated reduced corrosion rates for conventional chromium (III) based coatings, no improvement was observed for micro-cracked chromium coatings.



Mejia Chueca, Maria del Carmen; Graske, Marcus; Winter, Andreas; Baumer, Christoph; Stich, Michael; Mattea, Carlos; Ispas, Adriana; Isaac, Nishchay Angel; Schaaf, Peter; Stapf, Siegfried; Jacobs, Heiko O.; Bund, Andreas
Electrodeposition of reactive aluminum-nickel coatings in an AlCl3:[EMIm]Cl ionic liquid containing nickel nanoparticles. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 170 (2023), 7, 072504

The electrodeposition of aluminum-nickel coatings was performed by pulsed direct current in the ionic liquid (IL) 1.5:1 AlCl3:EMIm]Cl containing nickel nanoparticles (Ni NPs), for reactive dispersion coating application. Several electrochemical and characterization techniques were used to shed more light on the mechanism of Ni particle incorporation into the Al matrix. Thus, particle incorporation at the early stage of the deposition would mainly take place via particle adsorption at the substrate. However, as the thickness of the coating increases, it seems that the main mechanism for particle incorporation is via the reduction of ions adsorbed at the particles surface. Although a considerable high incorporation of Ni NPs has been achieved from the IL containing the highest concentration of Ni NPs (i.e. ∼33 wt% from a 20 g/L of Ni NPs bath), a high concentration of NPs in the IL resulted having a negative effect in terms of quality of the coatings, due to solidification of the electrolyte in a poorly conductive compound. Moreover, almost equivalent amounts of Ni and Al (Ni ∼45 wt.%and Al ∼44 wt.%) have been detected in some areas of the coatings. Such a layer composition would be desired for the targeted application.



https://doi.org/10.1149/1945-7111/ace382
Böttcher, René; Mai, Sebastian; Borisenko, Natalia; Ispas, Adriana; Bund, Andreas; Endres, Frank
A Raman study on the speciation of different metal ions in an AlCl3-based ionic liquid. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 170 (2023), 7, p072503

The speciation of Cr, Zn and Sn in AlCl3/1-ethyl-3-methylimidazolium chloride containing CrCl2, ZnCl2 and SnCl2, respectively, has been studied by cyclic voltammetry (CV), Raman spectroscopy and density functional theory (DFT) calculations. Addition of the respective metal salt causes the current waves in the CV to decrease, indicating a reaction of the metal salts with Al2Cl7−. Compared to the neat electrolyte, the Raman peaks of Al2Cl7− decrease while the AlCl4− peak increases in intensity, broadens and shifts towards lower wavenumbers. Calculated wavenumbers of metal complexes [Me(AlCl4)3]− reflect these observations. DFT calculations of the Gibbs free energies of formation, solvation and reaction support the formation of the proposed complexes. The central ions are coordinated by three bidentate AlCl4− ligands that are arranged planar-trigonally. Due to the occupied Sn-5s orbital, repulsive forces cause a trigonal-pyramidal geometry in case of the Sn complex. Based on the similarities in the experimental observations and the orbital configuration of Zn2+ compared to Cr2+, the spontaneous formation of the species [Cr(AlCl4)3]− can be assumed.



https://doi.org/10.1149/1945-7111/ace383
Kurniawan, Mario; Ivanov, Svetlozar
Electrochemically structured copper current collectors for application in energy conversion and storage: a review. - In: Energies, ISSN 1996-1073, Bd. 16 (2023), 13, 4933, S. 1-33

Copper current collectors (Cu CCs) impact the production technology and performance of many electrochemical devices by their unique properties and reliable operation. The efficiency of the related processes and the operation of the electrochemical devices could be significantly improved by optimization of the Cu CCs. Metallic Cu plays an important role in electrochemical energy storage and electrocatalysis, primarily as a conducting substrate on which the chemical processes take place. Li nucleation and growth can be influenced by the current collector by modulating the local current density and Li ion transport. For example, the commonly used planar Cu CC does not perform satisfactorily; therefore, a high number of different modifications of Cu CCs have been proposed and reported in the literature for minimizing the local current density, hindering Li dendrite formation, and improving the Coulombic efficiency. Here, we provide an updated critical overview of the basic strategies of 3D Cu CC structuring, methodologies for analyzing these structures, and approaches for effective control over their most relevant properties. These methods are described in the context of their practical usefulness and applicability in an effort to aid in their easy implementation by research groups and private companies with established traditions in electrochemistry and plating technology. Furthermore, the current overview could be helpful for specialists with experience in associated fields of knowledge such as materials engineering and surface finishing, where electrochemical methods are frequently applied. Motivated by the importance of the final application of Cu CCs in energy storage devices, this review additionally discusses the relationship between CC properties and the functional parameters of the already-implemented electrodes.



https://doi.org/10.3390/en16134933
Isaac, Nishchay Angel; Schlag, Leslie; Ispas, Adriana; Reiprich, Johannes; Soydan, Alper K.; Moreira, Pedro H. O.; Thiele, Sebastian; Aliabadian, Bardia; Flock, Dominik; Knauer, Andrea; Jiménez, Juan J.; Bund, Andreas; Morales Sánchez, Francisco Miguel; Pezoldt, Jörg; Jacobs, Heiko O.
Novel gas phase route toward patterned deposition of sputter-free Pt/Al nanofoils. - In: Advanced Materials Technologies, ISSN 2365-709X, Bd. 8 (2023), 18, 2300448, S. 1-8

This article reports a new approach toward fabrication and directed assembly of nanoparticulate reactive system (Nanofoils) on patterned substrates. Different from current state-of-the-art, gas phase electrodeposition uses nanoparticles instead of atoms to form densely packed multilayered thin films at room temperature-pressure. On ignition, the multilayer system undergoes an exothermic self-propagating reaction. The numerous contact points between two metallic nanoparticulate layers aid in high heat release. Sub-10-nm Platinum (Pt) and Aluminum (Al) particles are synthesized through cathode erosion of metal electrodes in a flow of pure nitrogen gas (spark ablation). Pt/Al bilayer stacks with total thickness of 3–8 µm undergo self-propagating reaction with a 10.3 mm s−1 wavefront velocity on local ignition. The reaction wavefront is captured using high speed videography. Calorimetry studies reveal two exothermic peaks suggesting Pt/Al alloy formation. The peak at 135 ˚C has a higher calorific value of 150 mW g−1 while the peak at 400 ˚C has a 12 mW g−1 exothermic peak. X-ray diffraction study shows reaction-products are cubic Al2Pt with small quantities of orthorhombic Al6Pt and orthorhombic AlPt2. Electron microscopy studies help draw a correlation between film morphology, bimetallic interface, nanoparticle oxidation, and self-propagating reaction kinetics that is significant in broadening our understanding towards nanoparticulate reactive systems.



https://doi.org/10.1002/admt.202300448
Böttcher, René; Ispas, Adriana; Bund, Andreas
Binary aluminum alloys from 1-ethyl-3-methylimidazolium-based ionic liquids for cathodic corrosion protection. - In: Metals, ISSN 2075-4701, Bd. 13 (2023), 2, 377, S. 1-15

Aluminum cannot provide continuous cathodic corrosion protection under ambient conditions due to the formation of an insulating oxide layer and therefore it should be alloyed. Binary aluminum alloys with Cr, Zn and Sn from AlCl3/1-ethyl-3-methylimidazolium chloride ([EMIm]Cl) containing CrCl2, ZnCl2 or SnCl2 have been deposited and their morphology and composition were investigated using SEM/EDS. The corrosion behavior of alloys with 2–4 wt% Cr, Zn or Sn was investigated using potentiodynamic polarization in 3.5 wt% NaCl solution, neutral salt spray test (NSS) and environmental exposure (EE). Pure aluminum provides excellent corrosion protection of steel in a chloride-containing environment, but not under ambient conditions. AlCr alloys show poor corrosion protection while AlZn alloys provide excellent corrosion protection in the NSS test and superior cathodic protection in the EE test compared to aluminum. AlSn alloys are highly active at even low tin contents and dissolve rapidly in chloride-containing electrolytes. However, a slightly improved cathodic protection in the EE test compared to pure aluminum has been observed. The results prove the necessity of alloying aluminum to achieve effective cathodic corrosion protection under mild atmospheric conditions.



https://doi.org/10.3390/met13020377
Arciniega, Luciano Bellatin; Yapu, Raúl Meza; Valencia, Daniel Obregón; Hadzich, Antonella; Costa, Marcus A.; Ispas, Adriana; Bund, Andreas; Flores, Santiago
Alkyds with artistic applications based on drying oils, multifunctional polyalcohols and different polybasic acids. - In: Journal of applied polymer science, ISSN 1097-4628, Bd. 140 (2023), 16, e53746, S. 1-12

Today's requirements in the art field have challenged researchers to create artistic paintings with attractive appearance and long-term color stability. Alkyd-based art mediums have become an important group in the art field, because of their similar characteristics to traditional oils and exceptional drying properties. In this work, high solid alkyd-based art mediums have been synthesized by the monoglyceride and acidolysis processes. Multifunctional polyols and high unsaturated fatty acid sources were compared and used for alkyd synthesis. The use of a non-traditional oil of Peruvian origin is proposed. Resins have been characterized according to their physicochemical (acid number, viscosity, color and density) and drying properties. Drying tendencies were verified with the use of quartz crystal microbalance. Also, the behavior of the art mediums mixed with commercial oil paintings and a dry pigment, have also been evaluated. Results indicate that resins containing the polyol with the highest functionality are more viscous and have fewer tendencies to yellowing, while non-traditional Peruvian oil is the best option for creating light-colored art mediums. Alkyd mediums prepared by the monoglyceride method gave to oil paintings better characteristics and drying behavior on canvas.



https://doi.org/10.1002/app.53746
Endrikat, Anna; Eggert, Lara; Di Maglie, Alex; Attenberger, Klaus; Neumann, Tom; Quoß, Mathias; Bouhrouch, Dalal; Bund, Andreas
Innovative Fertigung von Leiterplatten durch FDM-Druck und selektive Kunststoffmetallisierung. - In: WOMag, ISSN 2195-5891, Bd. 12 (2023), 4, S. 9-11

Mit Hilfe von additiven Fertigungsverfahren lassen sich Kunststoffe mit unterschiedlichen Eigenschaften zu einem Produkt kombinieren. Dies erlaubt es, die Grundeinheiten von elektrischen Leiterplatten mittels Drucktechnik herzustellen, wobei der Aufwand weitgehend unabhängig von der hergestellten Stückzahl ist. Durch Drucken mit metallisierbaren Kunststoffen gelingt es, Leiterbahnen mit akzeptabler Leitfähigkeit auf elektrisch isolierendem Trägermaterial zu erzeugen. Die bisherigen Entwicklungen sind auf die Verwendung von Kunststoff mit einer maximalen Temperaturbelastung bis etwa 100 ˚C beschränkt. Um die bestehenden Verfahren der Leiterplattentechnik nutzen zu können, muss diese Temperaturobergrenze deutlich erhöht werden.



Link, Steffen; Dimitrova, Anna; Krischok, Stefan; Ivanov, Svetlozar
Electrochemical deposition of silicon in organic electrolytes. - In: Reference module in chemistry, molecular sciences and chemical engineering, (2023)

Electrodeposition is a versatile instrumental technique, already applied in many industrial fields. However, the deposition of silicon and other reactive elements is still challenging and requires further research and improvement. Accomplishing an efficient electrodeposition of silicon at room temperature is very attractive due to the high number of manufacturing technologies that would benefit from this approach. This work provides an overview of the electrochemical approaches for silicon deposition performed in organic electrolytes. The main factors that impact this process are individually discussed and exemplified with appropriately updated literature sources. Furthermore, the previously available research on characterization of electrodeposited silicon containing layers is provided. These studies are presented in the context of better understanding the structure, composition, and functional properties of the deposited silicon material, which may attract the attention of young academic scientists and process engineers.



https://doi.org/10.1016/B978-0-323-85669-0.00005-2
Najeeb, Mussab; Schwalbe, Ulf
Monitoring considerations of second life lithium ion batteries in battery energy storage systems. - In: PCIM Europe 2022, (2022), S. 1905-1914

This paper presents an analytical study of the most important technical aspects that should be considered in the methodologies for monitoring second-life lithium-ion batteries in stationary energy storage systems. The study is based, on one hand, on the specificity of these batteries in terms of changing their response differently in the second-life than in the first to external and operational influences. On the other hand, it is based on the monitoring requirements of storage systems to obtain an improved monitoring system with sufficient accuracy and more efficient performance of batteries in their second-life.



https://doi.org/10.30420/565822263
Najeeb, Mussab; Schwalbe, Ulf
Incorporating state of charge estimation methods towards more accurate monitoring of second-life lithium-ion batteries. - In: 2022 13th International Renewable Energy Congress (IREC), (2022), insges. 6 S.

Although several methods are developed for estimating the state of charge of lithium-ion batteries, there is still a challenge regarding monitoring the second life of these batteries due to the expected difference in the behavior and operating conditions in their second life. Considering that each method has its advantages and disadvantages according to the application and operating conditions, and monitoring the batteries in their second life is of special importance because it is required to integrate with the battery management system to balance cells, diagnose faults and prevent overheating. Therefore, the estimation method developed in this study, by incorporating artificial neural network method and Kalman filter method with fine-tuning of the filtering process using Coulomb counting, provides a solution for more accurate online monitoring of these batteries. Aiming to get the best possible performance, considering the specificity of the second life of the batteries in terms of operating voltage, low values of expected capacity, discharge ratio and other operational parameters.



https://doi.org/10.1109/IREC56325.2022.10002052
Endrikat, Anna; Eggert, Lara; Di Maglie, Alex; Neumann, Tom; Goldstein, Max; Attenberger, Klaus; Bouhrouch, Dalal; Schlosser, Michel; Bund, Andreas
Innovation processing of circuit boards with FDM printing and selective electrochemical metallization. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2022-01 (2022), 57, 2369

https://doi.org/10.1149/MA2022-01572369mtgabs
Kovácsovics, Iris;
A systematic approach for controlling electrodeposition based on studies of an acidic copper electrolyte. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (122 Seiten)
Technische Universität Ilmenau, Dissertation 2022

Bekannte akademische Erkenntnisse der Elektrochemie, wie die Butler-Volmer Kinetik, und deren Veränderungen ermöglichen unter anderem einen genaueren Einblick in den Mechanismus der Metallabscheidung. Aufgrund eines fehlenden Bindegliedes wurden diesen akademischen Erkenntnissen keine oder nur wenig Beachtung in der industriellen Prozessüberwachung geschenkt. Stattdessen wird die Hull-Zell-Abscheidung als indirekter Ansatz für die Analyse des Abscheidungsverhaltens benutzt. Durch die Entwicklung einer Methode, die die Randelemente-Methode als Grundlage für die Simulation verwendet, werden die kinetischen Parameter - die Austauschstromdichte j0 und der Transferkoeffizient α - aus experimentellen Hull-Zellen-Abscheidungen gewonnen (Rückwärtsbestimmung). Dieser Ansatz wird validiert, indem zyklische voltammetrische Daten eines sauren Kupferelektrolyten in die Simulation eingesetzt und die simulierten Hull-Zellkurven mit experimentellen Kurven verglichen werden. Darüber hinaus wird der Einfluss von Additiven auf das kinetische Verhalten untersucht, ohne die visuellen Informationen und die Möglichkeiten zu verlieren, die strukturellen und physikalischen Eigenschaften der Metallabscheidung zu erhalten. Dieser Ansatz kann zu einem tieferen elektrochemischen Verständnis von industriell benutzten Elektrolyten führen.



https://doi.org/10.22032/dbt.55223
Böttcher, René; Bund, Andreas; Ispas, Adriana
Abscheidung von Aluminiumlegierungen aus ionischen Flüssigkeiten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 113 (2022), 10, S. 1299-1304

Umweltfreundliche Schichten aus Aluminiumlegierungen werden gegenüber Schichten aus bedenklichen Metallen wie Cadmium zunehmend interessanter. Allerdings können sie mittels galvanischer Verfahren nur aus aprotischen Elektrolyten, wie ionischen Flüssigkeiten, abgeschieden werden. Um eine hohe Prozessstabilität zu erzielen, können Multianoden eingesetzt werden.



Gambaro, Sofia; Nascimento, M. Lucia; Shekargoftar, Masoud; Ravanbakhsh, Samira; Sales, Vinicius; Paternoster, Carlo; Bartosch, Marco; Witte, Frank; Mantovani, Diego
Characterization of a magnesium fluoride conversion coating on Mg-2Y-1Mn-1Zn screws for biomedical applications. - In: Materials, ISSN 1996-1944, Bd. 15 (2022), 22, 8245, S. 1-18

MgF2-coated screws made of a Mg-2Y-1Mn-1Zn alloy, called NOVAMag® fixation screws (biotrics bioimplants AG), were tested in vitro for potential applications as biodegradable implants, and showed a controlled corrosion rate compared to non-coated screws. While previous studies regarding coated Mg-alloys have been carried out on flat sample surfaces, the present work focused on functional materials and final biomedical products. The substrates under study had a complex 3D geometry and a nearly cylindrical-shaped shaft. The corrosion rate of the samples was investigated using an electrochemical setup, especially adjusted to evaluate these types of samples, and thus, helped to improve an already patented coating process. A MgF2/MgO coating in the µm-range was characterized for the first time using complementary techniques. The coated screws revealed a smoother surface than the non-coated ones. Although the cross-section analysis revealed some fissures in the coating structure, the electrochemical studies using Hanks’ salt solution demonstrated the effective role of MgF2 in retarding the alloy degradation during the initial stages of corrosion up to 24 h. The values of polarization resistance (Rp) of the coated samples extrapolated from the Nyquist plots were significantly higher than those of the non-coated samples, and impedance increased significantly over time. After 1200 s exposure, the Rp values were 1323 ± 144 Ω.cm2 for the coated samples and 1036 ± 198 Ω.cm2 for the non-coated samples, thus confirming a significant decrease in the degradation rate due to the MgF2 layer. The corrosion rates varied from 0.49 mm/y, at the beginning of the experiment, to 0.26 mm/y after 1200 s, and decreased further to 0.01 mm/y after 24 h. These results demonstrated the effectiveness of the applied MgF2 film in slowing down the corrosion of the bulk material, allowing the magnesium-alloy screws to be competitive as dental and orthopedic solutions for the biodegradable implants market.



https://doi.org/10.3390/ma15228245
Lucero Lucas, Gisella Liliana; Romanus, Henry; Ispas, Adriana; Bund, Andreas
Hollow platinum-gold and palladium-gold nanoparticles: synthesis and characterization of composition-structure relationship. - In: Journal of nanoparticle research, ISSN 1572-896X, Bd. 24 (2022), 12, 245, insges. 15 S.

Hollow palladium-gold (PdAu) and platinum-gold (PtAu) alloy nanoparticles (NPs) were synthesized through galvanic replacement reactions. PdAu NPs denoted PdAu-99.99 and PdAu-98 were produced using palladium precursors with different purity degree: Na2PdCl4 ≥ 99.99% and Na2PdCl4 98%, respectively. The effect of the addition time of the gold palladium precursor solution on the size of the generated NPs was evaluated. Two types of particles, with a rough and a smooth surface, were identified in the suspensions of PtAu and PdAu NPs by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and scanning transmission electron microscopy (STEM). The atomic percentage of gold, platinum, palladium, and cobalt (atomic %) in the nanoparticles was determined by energy dispersive X-ray spectroscopy (EDX). PtAu NPs (26-42 nm) contain Pt (41 at%), Au (36 at%), and Co (23 at%). Two groups of hollow palladium gold NPs (30-50 nm) with a different residual cobalt content were produced. PdAu-99.99 NPs consisted of Pd (68 at%), Au (26 at%), and Co (6 at%), whereas PdAu-98 NPs were composed of Pd (70 at%), Au (22 at%), and Co (8 at%). The hollow structure of the NPs was confirmed by EDX line scanning. Selected area electron diffraction analysis (SAED) revealed the formation of PtAu and PdAu alloys and it was used in estimating the lattice parameters, too.



https://doi.org/10.1007/s11051-022-05619-9
Quispe, Roger; Torres, Carlos; Eggert, Lara; Ccama, Gianella A.; Kurniawan, Mario; Hopfeld, Marcus; Zárate Moya, José Luis; Camargo, Magali K.; Rosenkranz, Andreas; Acosta, Julio A.; Bund, Andreas; Schaaf, Peter; Grieseler, Rolf
Tribological and mechanical performance of Ti2AlC and Ti3AlC2 thin films. - In: Advanced engineering materials, ISSN 1527-2648, Bd. 24 (2022), 10, 2200188, S. 1-11

Mn+1AXn (MAX) phases are novel structural and functional materials with a layered crystal structure. Their unique properties such as good machinability, high electrical conductivity, low friction, and corrosion resistance are appealing for many engineering applications. Herein, Ti2AlC and Ti3AlC2 MAX thin films are synthesized by magnetron sputtering and subsequent thermal annealing. A multilayer approach is used to deposit single-element nanolayers of titanium, aluminum, and carbon onto silicon substrates with a double-layer-diffusion barrier of SiO2 and SixNy. Ti2AlC and Ti3AlC2 thin films (thickness ≈500 nm) are formed via rapid thermal annealing and verified by X-Ray diffraction. Nanoindentation tests show hardness values of about 11.6 and 5.3 GPa for Ti2AlC and Ti3AlC2, respectively. The tribological behavior of the Ti2AlC and Ti3AlC2 thin films against AISI 52100 steel balls under dry sliding conditions is studied using ball-on-flat tribometry. The resulting coefficient of friction (CoF) for Ti2AlC and Ti3AlC2 ranges between 0.21-0.42 and 0.64-0.91, respectively. The better tribological behavior observed for Ti2AlC thin films is ascribed to its smaller grain size, reduced surface roughness, and higher hardness.



https://doi.org/10.1002/adem.202200188
Büker, Lisa;
Einfluss von Carbonsäuren auf den Abscheidungsprozess von Chrom aus Chrom(III)-Elektrolyten. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (xi, 115, LXVII Seiten)
Technische Universität Ilmenau, Dissertation 2022

Der Ersatz von hexavalenten Chromverbindungen in der galvanischen Industrie ist seit der Registrierung, Bewertung, Zulassung und Beschränkung chemischer Stoffe (REACH-Verordnung) der Europäischen Union ein zentrales Thema. In der dekorativen Verchromung ist die Substitution durch adäquate Alternativen sehr vielversprechend. Allerdings ist der Ersatz von CrVI-Verbindungen in der funktionellen Verchromung herausfordernd, denn Chromschichten aus trivalenten und hexavalenten Elektrolyten unterscheiden sich bspw. in der Farbe und Korrosionsbeständigkeit. In dieser Arbeit wird die Wirkungsweise verschiedener organischer Säuren auf die Abscheidung von dickeren Chromschichtdicken (> 1 µm) untersucht. Wichtige Instrumente, um die Reaktion und die Chromabscheidung zu untersuchen, sind zum einen die Hochleistungsflüssigkeits-Chromatographie (HPLC, engl. High performance liquid chromatography), elektrochemische Quarzmikrowaage (EQCM), Polarographie (DPP, engl. differential pulse polarography), die Zyklovoltammetrie (CV, engl. Cyclic voltammetry) und zum anderen Querschliffanalysen. Die Schichtcharakterisierung erfolgte über die Rasterelektronenmikroskopie (REM). Die Ergebnisse der Untersuchungen zeigten, dass Reaktionsgeschwindigkeit, Abscheideraten und der daraus resultierende Schichtaufbau, von der Art und Konzentration der Carbonsäuren abhängen. Es konnten Aussagen über die Wirkung der Carbonsäuren als Komplexbildner getroffen und mit dem Chelat-Effekt erklärt werden. Mit einer optimalen Elektrolytzusammensetzung konnten Schichtdicken von 25 bis zu 85 µm abgeschieden werden. Möglichkeiten, die eine gleichmäßige, rissarme Abscheidung unterstützen, wurden untersucht. Ein abschließender Vergleich der Chromschichten aus einem industriell genutzten sechswertigen Hartchromverfahren und dem hier beschriebenen dreiwertigen Elektrolyten zeigt gute Übereinstimmungen. Lediglich der Korrosionsschutz der Chromschicht aus dem trivalenten Elektrolyten ist nur mit Hilfe einer zusätzlichen Nickelschicht zu gewährleisten.



https://doi.org/10.22032/dbt.53060
Eckl, Maximilian; Böttcher, René; Wölk, Luca; Wingerath, Melina; Barbado Fernández, Carlos; Nascimento, M. Lucia; Göhler, Lukas; Stelzer, Daniel; Bund, Andreas
Elektrochemisches Glätten von Metallen durch ionenleitende Festkörper in schwach leitenden Lösungen. - In: WOMag, ISSN 2195-5891, Bd. 11 (2022), 6, S. 22-24

Link, Steffen; Ivanov, Svetlozar; Bund, Andreas
Elektrochemische Abscheidung von Silicium aus organischen Elektrolyten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 113 (2022), 7, S. 877-887

Silicium (Si) ist ein wichtiger Rohstoff für viele industrielle Anwendungen, u. a. für die Mikroelektronik, die Photovoltaikindustrie und neuerdings auch innerhalb der elektrochemischen Energiespeicherung. Für die Erweiterung des technischen Anwendungsspektrums von Si sind jedoch anpassbare Abscheidungstechnologien erforderlich.



Ahmadkhaniha, Donya; Krümmling, Josef; Zanella, Caterina
Electrodeposition of high entropy alloy of Ni-Co-Cu-Mo-W from an aqueous bath. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 169 (2022), 8, 082515, insges. 5 S.

This study aimed to deposit high entropy alloy (HEA) coatings with five different elements, Ni, Co, Cu, Mo, and W, from a single aqueous bath. The influence of pH, current density, and complex agent on the composition of deposited coating was examined. It was shown that Mo and W were codeposited mainly with Ni and Co. pH had the most impact on the codeposition of reluctant elements like Mo and W, while current density had the minimum effect. The deposited coating had a metallic, dense, and nodular morphology with configurational entropy of around 1.6 R.



https://doi.org/10.1149/1945-7111/ac87d5
Endrikat, Anna;
Elektrochemische Reduktion von Niob-Halogeniden in ionischen Flüssigkeiten. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (VIII, 98 Blätter, Blatt IX-LVII)
Technische Universität Ilmenau, Dissertation 2022

Metallische Überzüge aus Niob bieten aufgrund ihrer besonderen chemischen, thermischen und mechanischen Stabilität vor allem auf kostengünstigen Grundwerkstoffen, die extremen korrosiven und abrasiven Belastungen ausgesetzt sind, ein breites Anwendungsspektrum. Bis heute ist jedoch ein hoher verfahrenstechnischer Aufwand erforderlich, um haftfeste und hochreine Niob-Schichten in Niederdruck-Prozessen aus der Gasphase herzustellen. Elektrochemische Prozesse bieten eine kostengünstige Alternative, wobei die Reaktivität von Niob sowie das negative Standardpotential der meisten Niob-Reduktionsreaktionen den Einsatz wässriger Medien ausschließt. Die ionischen Flüssigkeiten (ILs) ermöglichen, durch ihre große elektrochemische und thermische Stabilität diese Lücke zu schließen und wurden daher als Medium für die elektrochemische Reduktion von Niob-Halogeniden intensiv untersucht. Im Rahmen meiner Arbeit wurden die Niob-Halogenide NbF5, NbCl5, NbBr5 und Nb(CH3cp)2Cl2 in vier ILs mit zyklischen Voltammetrie (CV), differentieller Pulsvoltammetrie (DPV), Infrarot- und Raman-Spektroskopie hinsichtlich ihrer Eignung als Elektrolyte untersucht. In Kombination mit potentiostatischen Abscheidungen zeigte sich, dass Niob-basierte Schichten abgeschieden werden konnten, dafür aber eine gute Löslichkeit des Niob-Halogenids, ein geringer Wassergehalt sowie eine erhöhte Temperatur des Elektrolyten essentiell sind. Analysen des Reduktionsmechanismus mit der rotierenden Ring-Scheiben-Elektrode (RRDE) belegen chemische Nebenreaktionen die auf Kom- und Disproportionierung der Niob-Spezies sowie Zersetzung der IL zurückgeführt werden. Mit Hilfe der elektrochemischen Quarzmikrowaage (EQCM) wurde die Einlagerung dieser Zersetzungsprodukte bestätigt. Die abgeschiedenen Schichten wurden mit Rasterelektronenmikroskopie (REM), energie-dispersiver Röntgenspektroskopie (EDX), Röntgenfluoreszenzanalyse (RFA), Photoelektronen-spektroskopie (XPS) sowie Röntgendiffraktometrie (XRD) charakterisiert. Diese Schichten weisen etwa 25 At.-% Niob auf. Die restlichen 75 At.-% sind Fremdelemente wie z.B. C, N, O, F, S, Cl bzw. Br, die auf Rückstände des Elektrolyten und der eingelagerten IL-Zersetzungsprodukte zurückgeführt werden. Die Niob-Spezies wurde nicht vollständig zum Metall reduziert und liegt in röntgenamorphen Verbindungen wie NbC, NbO bzw. gemischte NbC1-xOx (mit x ≤ 0,2) sowie NbO2 und Nb2O5 vor. NbCl5 in 1-Butyl-1-methylpyrrolidinium trifluoromethansulfonat ([BMP][OTf]) liefert die dicksten und homogensten Schichten und ist damit das aussichtsreichste System für die Niob-Reduktion. Die Schichteigenschaften können durch Substratvorbehandlung, Additiveinsatz, gepulste Potentialführung sowie Tempern weiter verbessert werden.



https://doi.org/10.22032/dbt.52026
Zhao, Yuguo; Yan, Yong; Liu, Chunyue; Zhang, Dongtang; Wang, Dong; Ispas, Adriana; Bund, Andreas; Du, Biao; Zhang, Zhengdong; Schaaf, Peter; Wang, Xiayan
Plasma-assisted fabrication of molecularly imprinted NiAl-LDH layer on Ni nanorod arrays for glyphosate detection. - In: ACS applied materials & interfaces, ISSN 1944-8252, Bd. 14 (2022), 31, S. 35704-35715

An inorganic-framework molecularly imprinted NiAl layered double hydroxide (MI-NiAl-LDH) with specific template molecule (glyphosate pesticide, Glyp) recognition ability was prepared on Ni nanorod arrays (Ni NRAs) through electrodeposition followed by a low-temperature O2 plasma treatment. The freestanding Ni/MI-NiAl-LDH NRA electrode had highly enhanced sensitivity and selectivity. The electrocatalytic oxidation of Glyp was proposed to occur at Ni3+ centers in MI-NiAl-LDH, and the current response depended linearly on the Glyp concentration from 10.0 nmol/L to 1.0 μmol/L (R2 = 0.9906), with the limit of detection (LOD) being 3.1 nmol/L (S/N = 3). An exceptional discriminating capability with tolerance for other similar organophosphorus compounds was achieved. Molecular imprinting (N and P residues) affected the electronic structure of NiAl-LDH, triggering the formation of highly active NiOOH sites at relatively lower anodic potentials and substantially enhancing the electrocatalytic oxidation ability of the NiAl-LDH interface toward the C-N bonds in Glyp. In combination with the surface enrichment effect of MI-NiAl-LDH toward template molecules, the electrochemical oxidation signal intensity of Glyp increased significantly, with a greater peak separation from interfering molecules. These results challenge the common belief that the excellent performance of inorganic-framework molecularly imprinted interfaces arises from their specific adsorption of template molecules, providing new insight into the development of high-performance organic-pollutant-sensing electrodes.



https://doi.org/10.1021/acsami.2c08500
Deich, Tobias;
Optimierung der äußeren Druckbedingungen auf Li-Ionen Zellen zur Erhöhung der Lebensdauer. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (VI, 138 Seiten)
Technische Universität Ilmenau, Dissertation 2022

Li-Ionen Zellen dehnen sich während des Ladens aufgrund von Volumenänderungen der Aktivmaterialien bei der Lithium-Interkalation reversibel aus. Zusätzlich führen Alterungsmechanismen der Anode zu einem signifikanten und irreversiblen Wachstum der Zellen. Da die Zellen für ihren Einsatz in Elektrofahrzeugen in Modulen verspannt werden, führt diese Ausdehnung zu einem Anstieg des Drucks im Modul. Sowohl die Performance als auch die Alterung der Zellen sind abhängig vom äußeren Druck. Die Wechselwirkungen von Modulverspannung, Druckentwicklung und Alterung sind jedoch noch weitestgehend unbekannt, da in der Literatur bisher keine systematische Untersuchung von realistischen mechanischen Druckbedingungen durchgeführt wurde. Im Rahmen dieser experimentellen Arbeit wurden die Effekte der Modulsteifigkeit und der initialen Verspannung von Zellen auf die zyklische und kalendarische Alterung, das Zelldickenwachstum und die Druckentwicklung im Modul anhand von drei unterschiedlichen Zelltypen untersucht, die für den Einsatz in Elektrofahrzeugen entwickelt wurden. Auf Basis der statistischen Versuchsplanung konnten die Effekte modelliert und hinsichtlich ihrer statistischen Signifikanz bewertet werden. Im Anschluss wurden die dominanten Alterungsmechanismen und die limitierenden Alterungseffekte im Rahmen einer elektrochemischen Charakterisierung und Post-Mortem-Analyse identifiziert. Den größten Effekt auf die Druckentwicklung im Modul hat die Modulsteifigkeit, ein Einflussfaktor, der bisher in der Literatur weitestgehend vernachlässigt wurde. Der Einfluss der initialen Verspannung hängt stark von den mechanischen Eigenschaften der Zelle ab. Alle drei Zelltypen zeigen druckabhängige Alterungseffekte und -mechanismen, wie z. B. Kathoden-Aktivmaterialverluste aufgrund von Partikelbrüchen, eine zunehmend inhomogene Alterung oder Li-Plating an den Rändern der Anode. Im letzten Schritt wurde das mechanische Moduldesign hinsichtlich der volumetrischen Energiedichte über die Lebensdauer optimiert. Im Rahmen einer experimentellen Optimierung wurde der Einfluss des Designs von Pufferelementen auf die volumetrische Energiedichte bei zyklischer Alterung untersucht und ein optimales Design abgeleitet.



https://doi.org/10.22032/dbt.52195
Peipmann, Ralf; Bund, Andreas; Schmidt, Udo
Simulation verschiedener Hull-Zellen-Geometrien, Teil 2 - Erweiterung der Simulationsmodelle mittels 3D. - In: Galvanotechnik, ISSN 0016-4232, Bd. 113 (2022), 5, S. 575-585

Kovácsovics, Iris; Patzelt, Thomas; Herrmann, Johannes; Bund, Andreas
Reverse numerical simulation of kinetic parameters from acidic copper Hull cell deposition. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 169 (2022), 5, 052501

Hull cell depositions are industrially used to monitor electrolytes and study the influence of additives. By combining the Hull cell deposition and a numerical simulation based on the boundary element method via a curve-fitting approach allows to obtain kinetic parameters (e.g. transfer coefficient, exchange current density) and assessing the effects of additives without losing the visual information and the opportunity to get the structural and physical properties of the metal deposition (reverse determination). In an acidic copper electrolyte, an additive based on polyethylene glycol decreases the effective exchange current density, by up to two orders of magnitude, while the transfer coefficient is hardly influenced. By adding another additive based on bis-(3-sulfopropyl)disulphide, the effect is counteracted and increases in dependence on the ratio of both additives. The combined approach enables obtaining more information about visual and structural effects and the deposition kinetics from one experimental analysis.



https://doi.org/10.1149/1945-7111/ac694c
Pegel, Hendrik; Kessel, Otto; Heugel, Philipp; Deich, Tobias; Tübke, Jens; Birke, Peter; Sauer, Dirk Uwe
Volume and thickness change of NMC811|SiOx-graphite large-format lithium-ion cells: from pouch cell to active material level. - In: Journal of power sources, ISSN 1873-2755, Bd. 537 (2022), 231443

In this study, the reversible thickness change of a large-format lithium-ion automotive pouch cell is investigated under precisely monitored cell pressure and temperature using an in-house built actively controlled pneumatic cell press. The quantitative and qualitative contribution of the state-of-the-art NMC811 cathode and the SiOx-graphite composite anode to the total pouch cell expansion is resolved by electrochemical dilatometry and validated. Results show that Ni-rich cathodes have a significant impact on the pouch cell expansion and exhibit highly nonlinear thickness change which is related to the change of the individual lattice parameters of the crystal structure. To resolve the contribution of both anode active materials to the total anode expansion, the capacities of SiOx and graphite are determined by differential voltage analysis and validated with half-cell measurements. Then, the volume expansion of SiOx and graphite as a function of the anode state of charge is calculated. By introducing fitting parameters and applying theories about the interaction of SiOx with the surrounding morphology the correlation between the volume expansion of the active materials and the thickness change of the SiOx-Gr composite anode is investigated. The findings suggest that there is significant nonlinear reduction of pore volume at low state of charge.



https://doi.org/10.1016/j.jpowsour.2022.231443
Link, Steffen; Dimitrova, Anna; Krischok, Stefan; Ivanov, Svetlozar
Reversible sodiation of electrochemically deposited binder- and conducting additive-free Si-O-C composite layers. - In: Energy technology, ISSN 2194-4296, Bd. 10 (2022), 5, 2101164, S. 1-9

Binder- and conducting additive-free Si-O-C composite layers are deposited electrochemically under potentiostatic conditions from sulfolane-based organic electrolyte. Quartz crystal microbalance with damping monitoring is used for evaluation of the layer growth and its physical properties. The sodiation-desodiation performance of the material is afterward explored in Na-ion electrolyte. In terms of specific capacity, rate capability, and long-term electrochemical stability, the experiments confirm the advantages of applying the electrochemically formed Si-O-C structure as anode for Na-ion batteries. The material displays high (722 mAh g^-1) initial reversible capacity at j = 70 mA g^-1 and preserves stable long-term capacity of 540 mAh g^-1 for at least 400 galvanostatic cycles, measured at j = 150 mA g^-1. The observed high performance can be attributed to its improved mechanical stability and accelerated Na-ion transport in the porous anode structure. The origin of the material electroactivity is revealed based on X-Ray photoelectron spectroscopic analysis of pristine (as deposited), sodiated, and desodiated Si-O-C layers. The evaluation of the spectroscopic data indicates reversible activity of the material due to the complex contribution of carbon and silicon redox centers.



https://doi.org/10.1002/ente.202101164
Kurniawan, Mario;
Preparation and characterization of cuprous oxide for improved photoelectrochemical performance. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (VI, 106 Seiten)
Technische Universität Ilmenau, Dissertation 2022

Die Photoelektrochemische (PEC) Wasserspaltung stellte eine nachhaltige und saubere Methode dar, um Wasserstoff zu erzeugen, ohne auf fossile Brennstoffe angewiesen zu sein. Der P-Typ Cu2O-Halbleiter ist ein vielversprechender Kandidat für die Verwendung als Photokathodenmaterial in Bezug auf Kosten, Verfügbarkeit, Lichtabsorption und Energiebandposition. Ein neuartiges und kostengünstiges Herstellungsverfahren für hochporöse Strukturen (55-80 Poren/mm2) von Cu2O-Photokathoden mit verbesserter PEC-Leistung unter ausschließlicher Verwendung der elektrochemischen Abscheidung wird vorgestellt. Dieses Verfahren beinhaltet drei Schritte, um ein stabiles und hochporöses Cu-Metallgerüst als Substrat für die Cu2O-Schichten herzustellen. Im ersten Schritt wurde ein Abscheideprozess unterstützt durch die dynamische Entwicklung von Wasserstoff-Blasen entwickelt, um poröse Cu-Strukturen mit feinen Porennetzwerken herzustellen. Die porösen Cu-Strukturen wurden durch Abscheidung homogener und kompakter Cu-Schichten auf den fein verästelten Porenwänden mechanisch verstärkt. Da die poröse Cu-Struktur nicht vollständig verstärkt war, wurde in einem dritten Schritt die teilweise verstärkte Struktur mit Hilfe von Ultraschall vom planaren Cu-Substrat abgelöst, um ein stabiles freistehendes poröses Netzwerk mit röhrenförmigen Durchgangsporen zu erhalten. Die Porengröße kann durch Veränderung der Abscheidezeit während des ersten Herstellungsschrittes leicht eingestellt werden. Cu2O-Schichten mit Dicken zwischen ˜0,5 und ˜3 [my]m wurden auf den freistehenden porösen Cu-Schichten durch Variation der Abscheidezeit elektrochemisch hergestellt. Die PEC-Wasserspaltung der Cu2O-Photokathoden wurde unter gepulser simulierter AM 1,5-Beleuchtung in einem wässrigen Elektrolyten aus 0,5 M Na2SO4 (pH 6) untersucht. Es wurde festgestellt, dass die Proben mit kleineren Poren den höchsten Photostrom von -2,75 mA cm-2 bei 0 V vs. RHE aufwiesen, gefolgt von -2,25 mA cm-2 für die Proben mit großen Poren, während ein niedriger Dunkelstrom beibehalten wurde. Diese Photoströme sind 120 % bzw. 80 % höher als die PEC-Leistung einer Cu2O-Schicht auf planarem Cu-Substrat, die mit den gleichen Abscheideparametern hergestellt wurde. Die hohe Leistung wird auf die vergrößerte Oberfläche durch die poröse Struktur, die dünne und homogene Bedeckung der Cu2O-Schicht mit kleiner Korngröße und die höheren Lochkonzentrationen zurückgeführt, wie die Mott-Schottky-Analyse zeigte. Die weitere Auswertung der freistehenden porösen Cu2O-Proben zeigte, dass sie eine direkte optische Durchlässigkeit von 14 % für die feinporigen Proben bzw. 23 % für die grobporigen Proben besitzen ([Lambda] = 400-800 nm). Die Herstellung des transluzenten Metallgerüsts mit Hilfe des elektrochemischen Abscheidungsprozesses wurde bisher nicht berichtet, sodass neue Innovationen für verschiedene Anwendungen, insbesondere im Bereich der Energiematerialien, ermöglicht werden.



https://doi.org/10.22032/dbt.51881
Leimbach, Martin;
Charakterisierung der elektrochemischen Abscheidung von Chrom aus Chrom(III)-Elektrolyten für dekorative Anwendungen. - Ilmenau : Universitätsbibliothek, 2022. - 1 Online-Ressource (XVI, 142 Seiten)
Technische Universität Ilmenau, Dissertation 2022

Dekorative Chromschichten sind im Alltagsleben omnipräsent, da sie Bauteiloberflächen ein ansprechendes Aussehen verleihen und zugleich Schutz vor Korrosion und Abrieb bieten. Verfahren zur elektrochemischen Abscheidung, welche bereits seit Jahrzehnten bekannt und gut verstanden sind, basieren auf sechswertigen Chromverbindungen. Eine zunehmend strengere Chemikaliengesetzgebung schränkt die Verwendung dieser Stoffe ein und macht eine langfristige Substitution bei industriellen Prozessen notwendig. Elektrolyte auf Basis von dreiwertigen Chromverbindungen haben sich dabei als Alternative erwiesen und drängen zunehmend auf den Markt. Chrom(III)-basierte Elektrolytsysteme sind jedoch bislang kein gleichwertiger Ersatz und zeigen unter anderem Schwächen in Bezug auf Abscheiderate und optisches Erscheinungsbild der Chromschichten. Diese Arbeit soll Beiträge zum Verständnis des Abscheideprozesses und der Schichtbildung aus Chrom(III)-Elektrolyten liefern, um darauf aufbauend Maßnahmen für die Optimierung ableiten zu können. So wurde der Abscheideprozess mittels in-situ Mikrogravimetrie, Messung des oberflächennahen pH-Wertes und Bestimmung des bei der Abscheidung entstehenden Wasserstoffes charakterisiert. Im Ergebnis wurde eine Theorie zum Abscheidemechanismus aufgestellt. Anhand von Farbmessungen, REM- und AFM-Aufnahmen konnte ein Zusammenhang zwischen Schichtmorphologie und Farbwerten der Schichten nachgewiesen werden, welcher anhand von Modellrechnungen bestätigt wurde. Chrom(III)- und Chrom(VI)-Elektrolyte zeigen markante Unterschiede im Schichtwachstum. Aufbauend darauf wurde die Nutzung von Pulsstrom mit niedriger Frequenz als Maßnahme zur Steuerung der Morphologie und damit des Farbtones der Chromschichten identifiziert und erfolgreich angewendet.



https://doi.org/10.22032/dbt.51591
Böttcher, René; Ispas, Adriana; Bund, Andreas
Anodic dissolution of aluminum and anodic passivation in [EMIm]Cl-based ionic liquids :
Anodische Auflösung und Passivierung von Aluminium in ionischen Flüssigkeiten auf Basis von [EMIm]Cl. - In: WOMag, ISSN 2195-5891, Bd. 11 (2022), 1/2, S. 27-29

Böttcher, René; Mai, Sebastian; Ispas, Adriana; Bund, Andreas
Aluminiumabscheidung und -auflösung in ionischen Flüssigkeiten auf Basis von [EMIm]Cl : Kinetik des Ladungstransfers und der geschwindigkeitsbestimmende Schritt. - In: WOMag, ISSN 2195-5891, Bd. 11 (2022), 3, S. 22-25

Büker, Lisa; Böttcher, René; Leimbach, Martin; Hahne, Tobias; Dickbreder, Reiner; Bund, Andreas
Influence of carboxylic acids on the performance of trivalent chromium electrolytes for the deposition of functional coatings. - In: Electrochimica acta, ISSN 1873-3859, Bd. 411 (2022), 140054

As a direct consequence of the restrictions on the use of hexavalent chromium compounds, the demand for a suitable replacement has arisen. In this work the electrodeposition of thick chromium layers (>1µm) from a trivalent electrolyte is investigated with the aim to identify an electrolyte composition for the deposition of hard functional coatings. These layers can be used to surface finish tribological components experiencing high wear rates or mechanical stress in applications such as coating printing cylinders, feed rollers or piston rods. The influence of different carboxylic acids (malonic acid, malic acid, glycolic acid) on the deposition has been studied. The effect of current density on the current efficiency was investigated using in-situ microgravimetry. For a technical application the electrolyte containing malonic acid was the most promising one and was further investigated regarding the properties of the deposits, such as surface morphology, crack formation, composition, thickness and hardness, aiming at properties as close as possible to those of hexavalent chromium. In comparison to hexavalent chromium, the layer of trivalent chromium showed the same properties in terms of crack formation, hardness and layer thickness (> 1 µm).



https://doi.org/10.1016/j.electacta.2022.140054
Schötz, Theresa; Gordon, Leo W.; Ivanov, Svetlozar; Bund, Andreas; Mandler, Daniel; Messinger, Robert J.
Disentangling faradaic, pseudocapacitive, and capacitive charge storage: a tutorial for the characterization of batteries, supercapacitors, and hybrid systems. - In: Electrochimica acta, ISSN 1873-3859, Bd. 412 (2022), 140072

Today's electrochemical energy storage technologies aim to combine high specific energy and power, as well as long cycle life, into one system to meet increasing demands in performance. These properties, however, are often characteristic of either batteries (high specific energy) or capacitors (high specific power and cyclability). To merge battery- and capacitor-like properties in a hybrid energy storage system, researchers must understand and control the co-existence of multiple charge storage mechanisms. Charge storage mechanisms can be classified as faradaic, capacitive, or pseudocapacitive, where their relative contributions determine the operating principles and electrochemical performance of the system. Hybrid electrochemical energy storage systems can be better understood and analyzed if the primary charge storage mechanism is identified correctly. This tutorial review first defines faradaic and capacitive charge storage mechanisms and then clarifies the definition of pseudocapacitance using a physically intuitive framework. Then, we discuss strategies that enable these charge storage mechanisms to be quantitatively disentangled using common electrochemical techniques. Finally, we outline representative hybrid energy storage systems that combine the electrochemical characteristics of batteries, capacitors and pseudocapacitors. Modern examples are analyzed while step-by-step guides are provided for all mentioned experimental methods in the Supplementary Information.



https://doi.org/10.1016/j.electacta.2022.140072
Chnani, Ahmed; Kurniawan, Mario; Bund, Andreas; Strehle, Steffen
Nanometer-thick hematite films as photoanodes for solar water splitting. - In: ACS applied nano materials, ISSN 2574-0970, Bd. 5 (2022), 2, S. 2897-2905

Photoelectrochemical (PEC) water splitting is one of the most promising sustainable methods for feasible solar hydrogen production. However, this method is still impractical due to the lack of suitable photoanode materials that are efficient, stable, and cost-effective. Here, we present a surprisingly simple fabrication method for efficient, stable, and cost-effective nanometer-thick hematite films utilizing a rapid, ambient annealing approach. In the oxygen evolution reaction, the fabricated hematite films exhibit a Faradaic efficiency of 99.8% already at 1 V versus the reversible hydrogen electrode (RHE), a real photocurrent density of 2.35 mA cm-2 at 1.23 V versus RHE, and a superior photo-oxidation stability recorded for over 1000 h. Considering the active surface area, the measured photocurrent density is higher than any value achieved so far by hematite and other single-material thin-film photoanodes. Hence, we show for the first time that undoped hematite thin films can compete with doped hematite and other semiconductor materials.



https://doi.org/10.1021/acsanm.2c00095
Mejia Chueca, Maria del Carmen; Kurniawan, Mario; Knauer, Andrea; Rumiche, Francisco; Bund, Andreas; Guerra, Jorge Andres
Localized surface states influence in the photoelectrocatalytic performance of Al doped a-SiC:H based photocathodes. - In: Materials science in semiconductor processing, ISSN 1873-4081, Bd. 143 (2022), 106474, insges. 10 S.

https://doi.org/10.1016/j.mssp.2022.106474
Camargo, Magali K.; Uebel, Martin; Kurniawan, Mario; Ziegler, Karl F.; Seiler, Michael; Grieseler, Rolf; Schmidt, Udo; Barz, Andrea; Bliedtner, Jens; Bund, Andreas
Selective metallization of polymers: surface activation of polybutylene terephthalate (PBT) assisted by picosecond laser pulses. - In: Advanced engineering materials, ISSN 1527-2648, Bd. 24 (2022), 4, 2100933, S. 1-15

https://doi.org/10.1002/adem.202100933
Waibel, Andreas; Ispas, Adriana; Fritz, Mathias; Bund, Andreas
Galvanische Abscheidung von Nickel-Chrom-Legierungsschichten. - In: WOMag, ISSN 2195-5891, Bd. 10 (2021), 10, S. 21-24

Bund, Andreas;
TU Ilmenau startet DFG-Projekt zur Optimierung von Lithiumionenbatterien. - In: WOMag, ISSN 2195-5891, Bd. 10 (2021), 7/8, S. 13

Dyck, Tobias; Bund, Andreas
Investigation of the contact resistance as a function of the temperature for connectors and wire terminals. - In: 30th International Conference on Electrical Contacts, (2021), S. 202-209

The hardness of coating materials such as tin or gold is temperature-dependent, so the contact area and thus the contact resistance change depending on the temperature. Contact resistance measurements are carried out on hard gold- and tin-coated connector contacts at elevated temperatures. It is shown that the contact resistance decreases significantly with increasing temperature. Tests are also being carried out with solid and stranded copper wires. In addition to the hardness, foreign layers on the copper conductors have a further influence on the contact resistance.



https://doi.org/10.22032/dbt.51522
Peipmann, Ralf; Bund, Andreas; Schmidt, Udo
Simulation verschiedener Hull-Zellen-Geometrien, Teil 1 - spezielle Elektrodengeometrien in 2D und 3D. - In: Galvanotechnik, ISSN 0016-4232, Bd. 112 (2021), 10, S. 1315-1323

Najeeb, Mussab; Schwalbe, Ulf; Bund, Andreas
Development of a dynamic model of lithium ion battery pack for battery system monitoring algorithms in electric vehicles. - In: 2021 23rd European Conference on Power Electronics and Applications (EPE'21 ECCE Europe), (2021), S. P.1-P.10

The main objective of this paper is to develop an accurate and a self-corrective model for lithium ion battery pack, based on the analysis of properties and performance of equivalent circuit models of pack's cells and the use of artificial neural networks. This model is expected to meet the requirements for improving the accuracy of battery state estimation required for the monitoring algorithms of the battery system in electric vehicles.The use of the neural network will make it possible to adjust and correct modelling deviations and errors in equivalent circuit model parameters by comparing the modelled cells voltage and the measured voltage and generating modified model parameters based on this comparison.The validation experimental results show that the parameters of the modified model contributed to reducing the error rate in the cell voltage by approximately 70-80% of the error rate in the equivalent circuit model voltage.



https://doi.org/10.23919/EPE21ECCEEurope50061.2021.9570709
Gabryelczyk, Agnieszka; Ivanov, Svetlozar; Bund, Andreas; Lota, Grzegorz
Corrosion of aluminium current collector in lithium-ion batteries: a review. - In: Journal of energy storage, ISSN 2352-152X, Bd. 43 (2021), 103226

Calendar and cycle ageing affects the performance of the lithium-ion batteries from the moment they are manufactured. An important process that occurs as a part of the ageing is corrosion of the current collectors, especially prominent in the case of the aluminium substrate for the positive electrode. Generally, aluminium resists corrosion due to the formation of a non-permeable film of native aluminium oxide. Nevertheless, at certain electrochemical conditions corrosion affects the interface of the current collector. As a consequence of corrosion, the cathode materials lose electrical and mechanical contact with the current collector, leading to capacity and power fading. Therefore, a deeper understanding of this process and effective corrosion inhibition are necessary to prevent the deterioration of the battery performance. This review provides an updated critical overview of the mechanisms of aluminium corrosion, methodologies for analysing this phenomenon, and approaches for its effective mitigation. As the influence of multiple factors on the corrosion process has a central impact, the review discusses how they specifically affect the undergoing processes. Therefore, appropriate examples of important factors like electrolyte composition, thermal conditions and electrochemical parameters are presented to explain the specific mechanism of aluminium corrosion. Since corrosion inhibition is an important technological issue with a tremendous economic impact the review summarises how to achieve this by adjusting the electrochemical system and enhancing the knowledge on the safe operation of the positive electrode.



https://doi.org/10.1016/j.est.2021.103226
Yan, Yong; Liu, Haocen; Liu, Chunyue; Zhao, Yuguo; Liu, Shuzhen; Wang, Dong; Fritz, Mathias; Ispas, Adriana; Bund, Andreas; Schaaf, Peter; Wang, Xiayan
Efficient preparation of Ni-M (M = Fe, Co, Mo) bimetallic oxides layer on Ni nanorod arrays for electrocatalytic oxygen evolution. - In: Applied materials today, ISSN 2352-9407, Bd. 25 (2021), 101185

Fabrication of economic and high-performance electrodes for electrocatalytic oxygen evolution reaction (OER) accounts for a crucial issue associated with developing powerful and practical water splitting systems. In this work, free-standing Ni/Ni-M (M = Fe, Co, Mo) bimetallic oxides core/shell nanorod arrays (Ni/Ni-M NRAs) were prepared through electroless deposition of transition metal species on black nickel sheet (nickel nanorod arrays (Ni NRAs)) followed by electrochemical oxidation. All three types of Ni/Ni-M NRAs demonstrated enhanced electrocatalytic activity toward oxygen evolution reactions (OER). Especially, Ni/Ni-Fe NRAs electrode exhibit small onset potential of 1.535 V at current density of 10 mA&hahog;cm^-2. In contrast, the OER durability of these three samples was distinct. At 500 mV constant overpotential, the current density loss in OER of Ni/Ni-Fe NRAs was merely 13.5% for a period of 20000 s; but Ni/Ni-Mo and Ni/Ni-Co NRAs had almost disappeared catalytic activity under the identical conditions. According to many reports, the results were different for the superior OER stability of Ni-based bimetallic catalysts. Electrochemical analysis revealed that the NRAs structure dramatically improves charge transfer efficiency and electrochemically active surface area (ECSA). The present study might provide a new insight to design and fabricate more practical and high-performance Ni-based electrodes for OER.



https://doi.org/10.1016/j.apmt.2021.101185
Najeeb, Mussab; Schwalbe, Ulf
Developing an advanced equivalent circuit model for a Li-ion battery for battery monitoring in electric vehicles. - In: PCIM Europe Digital Days 2021, (2021), S. 1493-1498

In the improved second-order equivalent circuit model (ECM) presented in this paper, the battery responses to operational (voltage and current) and non-operational (ambient temperature) parameters were taken into account to reach high accuracy to improve the estimation of state of charge (SOC) and state of health (SOH) of lithium–ion batteries (LIBs) of electric vehicles (EVs). Based on this model, the exponential-function fitting method is adopted to identify the battery parameters according to the test data collected from the experimental platform. The performance of the model is verified by comparing the experimental and simulated voltage under hybrid pulse power characterization (HPPC) test profile.



https://ieeexplore.ieee.org/document/9472423
Böttcher, René;
Elektrochemische Abscheidung von Aluminium und Aluminiumlegierungen aus ionischen Flüssigkeiten. - Ilmenau : Universitätsbibliothek, 2021. - 1 Online-Ressource (xiii, 100, LIX Seiten)
Technische Universität Ilmenau, Dissertation 2021

Die galvanische Abscheidung von Aluminium aus ionischen Flüssigkeiten (ILs) hat großes Potential für den Ersatz umweltbedenklicher Cd-Beschichtungen. Aufgrund der Ausbildung der natürlichen Al2O3 Schicht bei Kontakt mit Luftsauerstoff, ist Al nur bedingt für den kathodischen Korrosionsschutz geeignet. Um die Bildung der Oxidschicht einzuschränken, muss Al legiert werden. Trotz intensiver Forschung ist die Al-Abscheidung aus ILs noch nicht gänzlich verstanden. Der Einsatz löslicher Al Anoden ist weit verbreitet, die anodische Passivierung bei hohen Stromdichten ist aber ein limitierender Faktor, dessen Ursache noch nicht eindeutig geklärt wurde. Die Abscheidung von Al Legierungen wurde intensiv untersucht, ihre Eignung für den kathodischen Korrosionsschutz unter Umgebungsbedingungen wurde allerdings noch nicht ausreichend thematisiert. In dieser Arbeit wird die Abscheidung von Al, AlCr, AlZn und AlSn aus Chloraluminat-ILs untersucht. Die Elektrodenkinetik der Al Auflösung und Abscheidung sowie die Raten bestimmenden Schritte wurden mittels zyklischer Voltammetrie (CV), Impedanzspektroskopie und Chronopotentiometrie (CP) untersucht und Reduktions bzw. Oxidationsmechanismen wurden vorgeschlagen. Mittels linearer Polarisation (LSV), elektrochemischer Quarzmikrowaage (EQCM), CV und CP konnte die Ursache anodischer Passivierung ermittelt werden. Die Wirkungsweise der Vorbehandlung von Stahl mit anodischer Polarisation in der IL wurde untersucht und die Haftungsverbesserung wurde mit der mechanischen Verzahnung der Schicht im Substrat begründet. Die Abscheidung von AlCr, AlZn und AlSn auf Stahl wurde mittels CV, EQCM, REM, EDX und XRD charakterisiert. Ihr Korrosionsverhalten wurde in Hinblick auf den kathodischen Korrosionsschutz mittels LSV, neutralem Salzsprühnebeltest (NSS Test) und Freibewitterung (EE Test) untersucht. Al und AlZn bieten hervorragenden Korrosionsschutz im NSS Test. AlCr und AlSn versagen binnen weniger Tage. Im Gegensatz zu den anderen Beschichtungen, verzögert AlZn im EE Test die Bildung von Rotrost für mehr als ein Jahr, was es zu einer vielversprechenden Alternative zu Cd macht. Die Komplexierung der Metallionen in den Elektrolyten wurde mittels RAMAN Spektroskopie und DFT aufgeklärt. Es wurde gezeigt, dass sich Komplexe der Struktur [Me(AlCl4)3]- (Me = Zn, Sn) bilden.



https://doi.org/10.22032/dbt.48729
Deich, Tobias; Storch, Mathias; Steiner, Kai; Bund, Andreas
Effects of module stiffness and initial compression on lithium-ion cell aging. - In: Journal of power sources, ISSN 1873-2755, Bd. 506 (2021), 230163

The effects of automotive-related lithium-ion module design, i.e. module stiffness and initial compression during module assembly on cell aging, swelling and pressure evolution are still largely unknown. This paper presents the results of a long-term aging study of 12 large-format automotive graphite/NMC 622 pouch cells, cycled for different module stiffnesses and initial compressions using design of experiments. Statistical analysis of mechanical and aging data revealed significant nonlinear (interaction) effects of both factors on pressure evolution, capacity loss and increase in internal resistance of the cells. Pressure dependent cell aging is observed over 1000 cycles, which was related to loss of active material at the cathode from differential voltage analysis. Post-mortem analysis confirmed a cathode active material loss via half- and full-cell measurements of harvested electrodes. Cross-section SEM micrographs revealed increasing NMC-particle cracking with higher pressure. Based on this, a fatigue-based aging model was developed to describe the capacity loss due to pressure dependent particle cracking. The presented approach enables both improved modeling of pressure dependent aging and lifetime optimized module design



https://doi.org/10.1016/j.jpowsour.2021.230163
Wang, Honglei; Cheng, Pengfei; Shi, Jun; Wang, Dong; Wang, Hongguang; Pezoldt, Jörg; Stich, Michael; Chen, Runfeng; Aken, Peter Antonie van; Huang, Wei; Schaaf, Peter
Efficient fabrication of MoS2 nanocomposites by water-assisted exfoliation for nonvolatile memories. - In: Green chemistry, ISSN 1463-9270, Bd. 23 (2021), 10, S. 3642-3648

Efficient and green exfoliation of bulk MoS2 into few-layered nanosheets in the semiconducting hexagonal phase (2H-phase) remains a great challenge. Here, we developed a new method, water-assisted exfoliation (WAE), for the scalable synthesis of carboxylated chitosan (CC)/2H-MoS2 nanocomposites. With facile hand grinding of the CC powder, bulk MoS2 and water followed by conventional liquid-phase exfoliation in water, this method can not only efficiently exfoliate the 2H-MoS2 nanosheets, but also produce two-dimensional (2D) CC/2H-MoS2 nanocomposites. Interestingly, the intercalated CC in MoS2 nanosheets increases the interlayer spacing of 2H-MoS2 to serve as good candidates for the semiconductor devices. 2D CC/2H-MoS2 nanocomposites show superior electronic rectification effects in nonvolatile write-once-read-many-times memory (WORM) behavior with an ON/OFF ratio over 103, which can be rationally controlled by the weight ratios of CC and MoS2. These findings by the WAE method would open tremendous potential opportunities to prepare commercially available semiconducting 2D nanocomposites for promising high-performance device applications.



https://doi.org/10.1039/D1GC00162K
Morozov, Mikhail; Ivanov, Svetlozar; Kadirov, Marsil; Bund, Andreas
Facile synthesis of a binder-free 3D Ni/NiO microwire network with a nanostructured fiber surface for a negative electrode in Li-ion battery. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 51 (2021), 5, S. 815-828

Binder-free Ni/NiO microwire hybrid network with a nanostructured surface is synthesized by employing a facile and low-cost method, involving one-pot synthesis of Ni microwires, followed by their partial oxidation in air atmosphere. A combination of imaging, diffraction, thermodynamic and electrochemical methods has been applied to reveal the impact of the synthesis conditions on the energy storage performance of the Ni/NiO microwire networks. The thermal conditions for the synthesis have been optimized by means of thermogravimetric (TGA/DSC) analysis, where an appropriate temperature (T = 400 ˚C) for obtaining a low-defect NiO phase has been determined. The performed electrochemical characterisation of the materials has shown that setting a low temperature for the synthesis enables high reversible capacity and better cycling stability of the binder-free materials. When the Ni/NiO network structures are deposited by a conventional slurry-based technology, involving polymer binder and conductive additive, the high capacity and cycling stability of the anodes are preserved, independent of the temperature conditions of synthesis. Electrochemical impedance spectroscopy is applied to support the interpretation of our results.



https://doi.org/10.1007/s10800-021-01541-5
Schmidt, Udo; Peipmann, Ralf; Bund, Andreas
Zweidimensionale Simulation von Hull-Zellen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 112 (2021), 3, S. 301-311

Link, Steffen; Kurniawan, Mario; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas; Ivanov, Svetlozar
Enhanced cycling performance of binder free silicon-based anode by application of electrochemically formed microporous substrate. - In: Electrochimica acta, ISSN 1873-3859, Bd. 380 (2021), 138216, S. 1-9

In this work, an electrochemically formed porous Cu current collector (p-Cu) is utilized for the development of a high-performance binder-free silicon anode. Two electrolyte compositions based on sulfolane (SL) and [BMP][TFSI] ionic liquid (IL) are implemented for silicon deposition. The electrochemical experiments confirm the advantages of applying the p-Cu structure in terms of specific capacity, rate capability, and long-term cycling, where the best electrochemical properties have been observed for the Si deposited from SL electrolyte. The Si-based p-Cu anodes formed in SL display stable 2500 mAh g^-1 reversible capacity during the first 250 cycles and promising capacity retention. Compared to this result, the cycling performance of the same type of material deposited on flat Cu foil (f-Cu) showed significantly reduced capacity (1400 mAh g^-1) and inferior cycling performance. The positive effect can be attributed to the improved mechanical stability of the active material and accelerated ionic transport in the porous structure of the anode. The improved functional properties of the electrochemically deposited Si from SL electrolyte in p-Cu samples compared to those obtained in IL can be ascribed to differences in the chemical composition. While the layers deposited in SL electrolyte involve Si domains incorporated in a matrix containing C and O that offer high mechanical stability, the Si material obtained in IL is additionally influenced by N and F chemical species, resulting from active IL decomposition. These differences in the chemical surrounding of the Si domains are the primary reason for the inferior electrochemical performance of the material deposited from [BMP][TFSI] electrolyte. XPS analysis shows that the initial composition of the as deposited layers, containing a considerable amount of elemental Si, is changed after lithiation and that the electrochemical activity of the anode is governed by switching between the intermediate redox states of Si, where the carbon-oxygen matrix is also involved.



https://doi.org/10.1016/j.electacta.2021.138216
Kurniawan, Mario; Stich, Michael; Marimon, Mayra; Camargo, Magali K.; Peipmann, Ralf; Hannappel, Thomas; Bund, Andreas
Electrodeposition of cuprous oxide on a porous copper framework for an improved photoelectrochemical performance. - In: Journal of materials science, ISSN 1573-4803, Bd. 56 (2021), 20, S. 11866-11880

https://doi.org/10.1007/s10853-021-06058-y
Mejia Chueca, Maria del Carmen; Sánchez, Luis Francisco; Kurniawan, Mario; Eggert, Lara; Tejada, Alvaro; Camargo, Magali K.; Grieseler, Rolf; Rumiche, Francisco; Díaz, Isabel; Bund, Andreas; Guerra, Jorge Andrés
Analysis of the physical and photoelectrochemical properties of c-Si(p)/a-SiC:H(p) photocathodes for solar water splitting. - In: Journal of physics, ISSN 1361-6463, Bd. 54 (2021), 19, 195101, S. 1-12

The photoelectrochemical (PEC) properties of sputtered aluminum doped hydrogenated amorphous silicon carbide thin films grown on p-type crystalline silicon substrates were investigated in 1 M solution under chopped light illumination. Optical and structural properties of the top absorber layer were systematically assessed after post-deposition isochronical annealing treatments. Samples exhibited a noticeable improvement of the opto-electronic properties after thermal treatments. In addition, an abrupt enhancement of the photocurrent was observed reaching a saturation value of 17 mA cm^-2 at -1.75 V vs. Ag/AgCl (3.5 M KCl). In this research we propose that this enhancement effect is associated to a charge transfer kinetic mechanism influenced by surface states and the p-type substrate. The latter most likely due to the space charge region extending beyond the absorber layer reaching the substrate. Current density-potential and electrochemical impedance spectroscopy measurements in dark revealed a reduction of the native layer at cathodic potentials higher than -1 V vs. Ag/AgCl (3.5 M KCl), which contributes to the high charge transfer kinetic of the system. We believe that these results will contribute to understand the substrate influence in the PEC performance of top absorber layers in multilayer structures for solar water splitting.



https://doi.org/10.1088/1361-6463/abdb69
Wojciechowski, Jarosław; Kolanowski, Łukasz; Graâs, Małgorzata; Szubert, Karol; Bund, Andreas; Fic, Krzysztof; Lota, Grzegorz
Anti-corrosive siloxane coatings for improved long-term performance of supercapacitors with an aqueous electrolyte. - In: Electrochimica acta, ISSN 1873-3859, Bd. 372 (2021), 137840, S. 1-15

This paper reports on the impact that the corrosion of the stainless steel current collectors has on the performance fade of a symmetric, carbon/carbon electrochemical capacitor, operating with an aqueous electrolyte (1M Na2SO4). The results obtained by applying electrochemical ageing protocols (voltage-holding tests) confirm that the current collector of the positive electrode undergoes tremendous degradation during 200 h in the charged state. To prevent the detrimental impact of the corrosion, a hydrophobic siloxane coating has been successfully applied. In the case of siloxane-protected current collectors that are subjected to identical ageing protocols, no significant deterioration in the electrochemical capacitor performance was observed. The siloxane coating reduces the electrochemical corrosion rate of 316L stainless steel significantly, as the potentiodynamic polarization tests and the electrochemical impedance spectroscopy results show. The presence of the coating is demonstrated by the water contact angle measurements, atomic force microscopy and energy-dispersive X-ray spectroscopy analysis.



https://doi.org/10.1016/j.electacta.2021.137840
Ryzhkov, Nikolay V.; Ledovich, Olesya; Eggert, Lara; Bund, Andreas; Paszuk, Agnieszka; Hannappel, Thomas; Klyukin, Konstantin; Alexandrov, Vitaly; Skorb, Ekaterina V.
Layer-by-layer polyelectrolyte assembly for the protection of GaP surfaces from photocorrosion. - In: ACS applied nano materials, ISSN 2574-0970, Bd. 4 (2021), 1, S. 425-431

Polyelectrolyte layer-by-layer assemblies are known as protective coatings for corrosion inhibition. Here, we demonstrate that polyelectrolyte multilayers of poly(ethyleneimine) (PEI) and poly(styrene sulfonate) (PSS)-(PEI/PSS)x-adsorbed at the GaP(100) photocathode surface remarkably mitigate the photocorrosion of GaP without decreasing its photoconversion efficiency. The activity of the polybase-polyacid complex is based on buffering pH changes at the solid-liquid interface. We carried out ab initio molecular dynamics-based simulations of the GaP(100) surface in contact with liquid water and demonstrated that an increase in the proton concentration enhances GaP dissolution. We used the scanning vibrating electrode technique (SVET) to characterize the distribution of photocorrosion activity areas over bare and polyelectrolyte-coated GaP surfaces and we showed that a polyelectrolyte coating impedes the dissolution kinetics. Data obtained using the SVET were compared to photoetched pores on the semiconductor surface. Voltammetric and chronoamperometric measurements were also performed to evaluate photoconversion efficiencies before and after the application of the protective coatings.



https://doi.org/10.1021/acsanm.0c02768
Ante, Mirko; Sörgel, ¸Seniz; Opitz, Martin; Freudenberger, Renate; Bund, Andreas
Electrocatalysis of lithium (poly-) sulfides in organic ether-based electrolytes. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 167 (2021), 16, 166520, insges. 9 S.

https://doi.org/10.1149/1945-7111/abd60c
Pinate, Santiago; Ispas, Adriana; Leisner, Peter; Zanella, Caterina
Electrocodeposition of Ni composites and surface treatment of SiC nano-particles. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 406 (2021), 126663, insges. 8 S.

https://doi.org/10.1016/j.surfcoat.2020.126663
Böttcher, René; Ispas, Adriana; Bund, Andreas
Determination of transport parameters in [EMIm]Cl-based ionic liquids - diffusion and electrical conductivity. - In: Electrochimica acta, ISSN 1873-3859, Bd. 366 (2021), 137370

The density, electrical conductivity and diffusion coefficients of anions and cations in the ionic liquid AlCl3/1-ethyl-3-methylimidazolium chloride, [EMIm]Cl, were determined to study physical correlations of these important parameters. The density was measured for different molar ratios of AlCl3:[EMIm]Cl from 0.5:1 to 2.0:1 at ambient temperature. The diffusion coefficient of the electrochemically active heptachloroaluminate complex, Al2Cl7-, was measured for a molar ratio of 2:1 in the range of 25˚C to 100˚C. The corresponding current density and potential transients were discussed regarding the decomposition of the [EMIm]+ cation and deviation from the theoretical Cottrell behavior. The electrical conductivity was measured for molar ratios of 1.5:1 and 2:1 in the range of 25˚C to 100˚C. Both the diffusion coefficient and electrical conductivity can be described well by an Arrhenius law. The diffusion coefficients of AlCl4-, Al2Cl7- and [EMIm]+ were estimated from the Nernst-Einstein and Stokes-Einstein relation. The results indicate a strong impact of ion pairing in these electrolytes.



https://doi.org/10.1016/j.electacta.2020.137370
Torres, Carlos; Quispe, Roger; Calderón, Noely Z.; Eggert, Lara; Hopfeld, Marcus; Rojas, Christopher; Camargo, Magali K.; Bund, Andreas; Schaaf, Peter; Grieseler, Rolf
Development of the phase composition and the properties of Ti2AlC and Ti3AlC2 MAX-phase thin films - A multilayer approach towards high phase purity. - In: Applied surface science, Bd. 537 (2021), 147864

MAX phase thin films have been synthesized by thermal treatment of a Ti-Al-C multilayer system. The preparation of the multilayer system was carried out via magnetron sputtering. Based on the thickness ratio among the individual nanoscale monolayers (Ti, Al, C), the resulting MAX phase stoichiometry can be controlled. This paper describes the synthesis of both Ti2AlC and Ti3AlC2 MAX phases from the same precursor multilayer system which is composed of a sequence of Ti/Al/C pure elemental single layers with thicknesses of 14, 6, and 3.5 nm, respectively. This sequence is repeated 22 times with a total thickness of around 500 nm. Rapid thermal treatment tests were performed to study the phase development. The Ti2AlC MAX phase forms in a temperature range below 850 ˚C, whereas the Ti3AlC2 MAX phase starts to form at temperatures above 850 ˚C and reaches its highest phase purity at 950 ˚C. The thin film structures were studied by X-ray diffraction and Raman spectroscopy. Furthermore, the electrical and mechanical properties were investigated to gain more insights regarding the phase transformation and their influence on the thin film properties.



https://doi.org/10.1016/j.apsusc.2020.147864
Schlag, Leslie; Isaac, Nishchay Angel; Nahrstedt, Helene; Reiprich, Johannes; Ispas, Adriana; Stauden, Thomas; Pezoldt, Jörg; Bund, Andreas; Jacobs, Heiko O.
Nanoparticle gas phase electrodeposition: fundamentals, fluid dynamics, and deposition kinetics. - In: Journal of aerosol science, ISSN 1879-1964, Bd. 151 (2021), 105652, S. 1-15

This communication uncovers missing fundamental elements and an expanded model of gas phase electrodeposition; a relatively new and in large parts unexplored process, which combines particle generation, transport zone and deposition zone in an interacting setup. The process enables selected area deposition of charged nanoparticles that are dispersed and transported by a carrier gas at atmospheric pressure conditions. Two key parameters have been identified: carrier gas flow rate and spark discharge power. Both parameters affect electrical current carried by charged species, nanoparticle mass, particle size and film morphology. In combination, these values enable to provide an estimate of the gas flow dependent Debye length. Together with Langmuir probe measurements of electric potential and field distribution, the transport can be described and understood. First, the transport of the charged species is dominated by the carrier gas flow. In close proximity, the transport is electric field driven. The transition region is not fixed and correlates with the electric potential profile, which is strongly dependent on the deposition rate. Considering the film morphology, the power of the discharge turns out to be the most relevant parameter. Low spark power combined with low gas flow leads to dendritic film growth. In contrast, higher spark power combined with higher gas flow produces compact layers.



https://doi.org/10.1016/j.jaerosci.2020.105652
Bund, Andreas;
Anwendungen der Schwingquarzmethode in der Galvanotechnik. - In: ZVO-Report, (2020), 2, S. 42

Leimbach, Martin; Tschaar, Christoph; Schmidt, Udo; Bund, Andreas
Abscheidung von dekorativen Chromschichten mittels niederfrequenter Pulsabscheidung zur Anpassung des optischen Erscheinungsbilds. - In: WOMag, ISSN 2195-5905, Bd. 9 (2020), 6, S. 1-8

Das optische Erscheinungsbild von galvanisch abgeschiedenen Chromschichten ist eines der wichtigsten Kriterien für deren dekorative Anwendung. Für die dekorative Verchromung werden zunehmend Elektrolyte auf Basis von dreiwertigem Chrom als Ersatz für die bisher verwendeten Elektrolyte auf Basis von sechswertigem Chrom eingesetzt. Chrom aus Elektrolyten mit dreiwertigen Chromverbindungen neigt jedoch dazu, bei Dicken über 100 nm einen gelblichen Farbton zu haben, was für die meisten Anwendungen unerwünscht ist. Die Farbverschiebung hängt mit einer Änderung der Oberflächenmorphologie aufgrund des Wachstums der Chromkeime zusammen. Durch die Verwendung von gepulstem Strom mit Einschaltzeiten im Bereich von Sekunden wird das unerwünschte Kornwachstum unterdrückt und die Bildung frischer Kerne begünstigt. Dadurch bilden sich kompakte Chromschichten mit feinerem Gefüge und verbesserten Farbwerten. Ein bläuliches Aussehen und ein hoher Glanz werden bis zu einer Dicke von mehr als 200 nm beibehalten. Basierend auf den Ergebnissen wird eine Kombination aus konstantem und gepulstem Strom vorgeschlagen, die ein ähnliches visuelles Erscheinungsbild ergibt wie nur bei gepulstem Strom, jedoch die angestrebte Schichtdicke in deutlich kürzerer Zeit erreicht.



https://dx.doi.org/10.7395/2020/Leimbach1
Ispas, Adriana; Gruia, Violeta-Tincuta; Bund, Andreas
Chromium electroplating from Cr(III) in deep eutectic solvents. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2020-02 (2020), 59, 2908

https://doi.org/10.1149/MA2020-02592908mtgabs
Link, Steffen;
Aprotische Medien zur elektrochemischen Abscheidung von Silicium als neuartiges Anodenmaterial für Lithium-Ionen-Batterien. - Ilmenau : Universitätsbibliothek, 2020. - 1 Online-Ressource (xii, 95, XLIX Seiten)
Technische Universität Ilmenau, Dissertation 2021

Die elektrochemische Abscheidung von Silicium ist eine aussichtsreiche Alternative zu den derzeitigen energieintensiven Herstellungsverfahren. Bisher ist der Reduktionsprozess jedoch kaum verstanden und die Schichten weisen starke Kohlenstoff- und Sauerstoffverunreinigungen auf. Für den Einsatz als hochkapazitive Anoden in Lithium-Ionen-Batterien ist deshalb die Anpassung der Schichteigenschaften und chemischen Zusammensetzung erforderlich. Diese Parameter werden durch das verwendete Substrat, die Stabilität des Elektrolyten und dem angelegten Potential beeinflusst. Daher wird in dieser Arbeit die Reduktion von SiCl4 in diversen aprotischen Medien, u.a. 1-Butyl-1-methylpyrrolidinium Bis(trifluoromethylsulfonyl)imid ([BMP][TFSI]) und Sulfolan (SL), untersucht. Als Hauptanalysewerkzeug dient dabei die elektrochemische Quarzkristallmikrowaage mit Dissipationsüberwachung. Die morphologische und chemische Charakterisierung erfolgt mittels Rasterelektronenmikroskopie bzw. Röntgenphotoelektronenspektroskopie. Die Ergebnisse zeigen unabhängig von Substrat und Potential eine starke Zersetzung von [BMP][TFSI] während der Abscheidung. Die Menge an Si(0) unterscheidet sich jedoch auf den einzelnen Substraten und reicht von 18,1 at.% (Glaskohlenstoff - GC) bis 7,5 at.% (Ni). Im Gegensatz dazu wird die Reduktion von SiCl4 auf den Metallelektroden in SL bei niedrigen Potentialen kaum durch die Nebenreaktionen beeinträchtigt, wodurch doppelt so hohe Anteile an Si(0) in den Schichten erreicht werden. Auf GC verhindert die Zersetzung von SL eine erfolgreiche Abscheidung von Si. In beiden Elektrolyten nehmen Rauheit und Viskoelastizität des Si mit zunehmender Abscheidezeit (t>1h) zu. Das (De-)Lithiierungsverhalten der Schichten wird mittels galvanostatischer Zyklisierung in EC/DMC (1:1, v/v) - LiPF6 Elektrolyten bei verschiedenen spezifischen Strömen untersucht. Die Daten zeigen eine schnelle Abnahme der Kapazität aufgrund der hohen Volumenexpansion während der Legierungsbildung. Durch Verwendung eines porösen Kupfer-Stromabnehmers konnten die Zyklenstabilität, Ratenfähigkeit und Coulomb-Effizienz von aus SL abgeschiedenem Si jedoch deutlich verbessert werden. Selbst nach 1200 Zyklen besitzt das Material noch eine Kapazität von ca. 1,5 Ah/g. Darüber hinaus konnten keine Risse in der Schicht festgestellt werden, was die hohe Stabilität der Elektrode belegt.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2021000088
Ivanov, Svetlozar; Link, Steffen; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Electrochemical nucleation of silicon in ionic liquid-based electrolytes. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2020-01 (2020), 19, 1181

https://doi.org/10.1149/MA2020-01191181mtgabs
Baumer, Christoph;
Realisierung fähiger Prozesse in der Galvanotechnik. - Ilmenau : Universitätsbibliothek, 2020. - 1 Online-Ressource (139 Seiten)
Technische Universität Ilmenau, Dissertation 2020

Die vorliegende Dissertation beschreibt den Einsatz von Qualitätsmanagementmethoden in der Galvanotechnik, um die geforderten Schichteigenschaften zu jeder Zeit gewährleisten zu können. Im Sinne einer Null-Fehler-Strategie müssen dazu die Prozessschwankungen möglichst minimiert werden. Die Dissertation ist an die DMAIC-Methode der Six Sigma Philosophie (Define, Measure, Analyze, Improve und Control) angelehnt. In der Definitionsphase werden die grundlegenden Zusammenhänge der Galvanotechnik und der untersuchten Prozesse der Nickel- und Nickel-Phosphorabscheidung beschrieben. Als Schlussfolgerung daraus rückt die chemische Badzusammensetzung ins Zentrum der Untersuchung, da diese die Schichteigenschaften wesentlich bestimmt und prozessimmanenten Schwankungen unterliegt. Ausgehend von der Messung und Analyse der Konzentrationsschwankungen lassen sich Regeln zur Festlegung von Analyseintervallen und Eingriffsgrenzen zur Steuerung der Prozesse definieren. Diese münden in eine Neukonzipierung der Badführung mit dem Ziel Schwankungen zu minimieren. Darauf aufbauend lassen sich durch Bilanzierung der Reaktionen und Stoffverbräuche die komplexen Konzentrationsänderungen makroskopisch durch einfache chemische und physikalische Zusammenhänge beschreiben, wodurch sich Prozessveränderungen im Voraus berechnen lassen. Dazu ist die Ermittlung charakteristischer Kenngrößen, wie Verschleppung, Stromausbeute und Reaktionsumsätze nötig, die mit Hilfe eines numerischen Lösungsverfahrens aus den Prozessdaten selbst gewonnen werden können. Durch die Simulation der Konzentrationsänderungen lassen sich Maßnahmen definieren um möglichst stationäre Bedingungen in den galvanischen Bädern einzustellen. In der Kontrollphase werden die beschriebene Systematik und Umsetzung anhand ausgewählter Prozesse überprüft. Die berechneten Prozesskennwerte und Konzentrationsverläufe wiesen dabei eine Abweichung von etwa 10% im Vergleich zu den gemessenen Werten auf. Für die elektrolytische und chemische Nickel-Phosphorabscheidung konnten kurzfristige Prozessfähigkeiten über 2 erreicht werden. Ebenso konnte flankierend mit weiteren Verbesserungen der Ausschussanteil bei der Beschichtung von MID-Bauteilen (molded interconnect devices) von 3% auf dauerhaft weniger als 0,1% gesenkt werden. Dies zeigt, dass ein galvanischer Serienprozess die heutigen industriellen Anforderungen erfüllen kann.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2020000674
Dyck, Tobias;
Untersuchungen zu den tribologischen und elektrischen Eigenschaften zinnbeschichteter Kontaktoberflächen. - Ilmenau : Universitätsbibliothek, 2020. - 1 Online-Ressource (XIII, 130 Blätter)
Technische Universität Ilmenau, Dissertation 2020

An galvanisch beschichteten Kontaktgeometrien werden Kontaktwiderstandsmessungen, Reibversuche und Leiteranschlussuntersuchungen durchgeführt. Dabei werden hemisphärische, zylindrische und sickenförmige Geometrien mit unterschiedlichen Kontaktradien eingesetzt. Bei den Reibversuchen zeigen große Radien und zylindrische Kontaktgeometrien die günstigsten Verschleißeigenschaften. Dickere Zinnschichten führen zu einer höheren Verschleißbeständigkeit, allerdings auch zu erhöhten Reibkräften. Bei Zinnschichten führt die Relativbewegung zwischen zwei Kontaktpartnern bereits nach dem ersten Reibzyklus zu einer deutlichen Reduzierung des Kontaktwiderstands durch das Verdrängen der Oxidschicht aus dem Kontaktbereich. Nickel wird als Sperrschicht zwischen Kupfer und Zinn eingesetzt, zeigt aber auch bei den Verschleißversuchen günstige Eigenschaften. So steigt der Kontaktwiderstand weniger stark an als bei nicht unternickelten Kontakten. Eine signifikante Erhöhung der Verschleißbeständigkeit bei gleichzeitiger Reduzierung des Reibwerts kann durch den Einsatz von Schmieröl erreicht werden. Bei Kontaktwiderstandsmessungen ohne Relativbewegung zeigt sich für eine Hartgoldschicht, dass große Radien und zylindrische Kontaktgeometrien zu geringeren Kontaktwiderständen führen. Für Zinnschichten ist dieses Verhalten, je nach Schichtsystem, schwächer ausgeprägt oder nicht vorhanden. Unter Wärmeeinfluss zeigt sich eine Abnahme des Kontaktwiderstands mit zunehmender Temperatur für Hartgold- und Zinnschichten. Untersuchungen mit eindrähtigen Leitern zeigen für den betrachteten Kontaktkraftbereich bis 10 N ein elektrisch günstiges Verhalten bei kleinen Kontaktradien und dicken Zinnbeschichtungen. Für feindrähtige Leiter begünstigen breite Leiterpakete geringere Widerstandswerte. Durch die Entwicklung eines theoretischen Modells werden die mechanischen und elektrischen Vorgänge nachvollzogen. Es wird ein Modell für die Auslegung von Steckverbinderkontakten vorgestellt, welches auf einer analytischen Untersuchung der mechanischen, elektrischen und tribologischen Eigenschaften von Steckverbinderkontakten und daraus abgeleiteten Gleichungen basiert.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2020000642
Kurniawan, Mario; Stich, Michael; Marimon, Mayra; Camargo, Magali K.; Peipmann, Ralf; Hannappel, Thomas; Bund, Andreas
Electrodeposition of cuprous oxide on a free-standing porous Cu framework for photoelectrochemical water splitting. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2020-02 (2020), 15, 1425

https://doi.org/10.1149/MA2020-02151425mtgabs
Büker, Lisa; Dickbreder, Reiner; Böttcher, René; Sadowski, Sandra; Bund, Andreas
Investigation of the reaction kinetics of chromium(III) ions with carboxylic acids in aqueous solutions and the associated effects on chromium deposition. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 167 (2020), 16, 162509, insges. 8 S.

Electroplated chromium is an important industrial coating. Both in the decorative and functional field, research is being carried out to develop trivalent chromium electrolytes. In this work, the interaction between CrIII ions and carboxylic acids (malonic acid, malic acid, oxalic acid and glycolic acid) is investigated. The use of carboxylic acids to improve the current efficiency in trivalent chromium plating baths has been known for a long time. But the thermodynamics and kinetics of the associated complexing reactions are not well understood. It is shown that the complexes form at different rates depending on the acid and its concentration and have a varying influence on chromium deposition. For the development of a technical bath, care must be taken to ensure that the molar ratios between chromium and carboxylic acids can be controlled. This is possible with the HPLC method presented here.



https://doi.org/10.1149/1945-7111/abd1f4
Link, Steffen; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas; Ivanov, Svetlozar
Electrogravimetry and structural properties of thin silicon layers deposited in sulfolane and ionic liquid electrolytes. - In: ACS applied materials & interfaces, ISSN 1944-8252, Bd. 12 (2020), 51, S. 57526-57538

Potentiostatic deposition of silicon is performed in sulfolane (SL) and ionic liquid (IL) electrolytes. Electrochemical quartz crystal microbalance with damping monitoring (EQCM-D) is used as main analytical tool for the characterization of the reduction process. The apparent molar mass (Mapp) is applied for in situ estimation of the layer contamination. By means of this approach, appropriate electrolyte composition and substrate type are selected to optimize the structural properties of the layers. The application of SL electrolyte results in silicon deposition with higher efficiency compared to the IL 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, [BMP][TFSI]. This has been associated with the instability of the IL in the presence of silicon tetrachloride and the enhanced incorporation of IL decomposition products into the growing silicon deposit. X-ray photoelectron spectroscopy (XPS) analysis supports the results about the layer composition, as suggested from the microgravimetric experiments. Attention has been given to the impact of practically relevant substrates (i.e., Cu, Ni, and vitreous carbon) on the reduction process. An effective deposition can be carried out on the metal electrodes in both electrolytes due to accelerated reaction kinetics for these types of substrates. However, on vitreous carbon (VC), a successful reduction of SiCl4 can only be accomplished in the IL, while the electroreduction process in SL is dominated by the decomposition of the electrolyte. For short deposition times, the scanning electron microscopy (SEM) images display rough morphologies in the nanometer range, which evolve further to structures with increased length scale of the surface roughness. The development of a rough interface during deposition, resulting in QCM damping at advanced stages of the process, is interpreted by a model accounting for the resistive force caused by the interaction of the liquid with a nonuniform layer interface. By using this approach, the individual contributions of the surface roughness and viscoelastic effects to the measured damping values are estimated.



https://doi.org/10.1021/acsami.0c14694
Hesamedini, Sanaz;
Trivalent chromium based conversion coatings containing cobalt on the zinc plated steel. - Ilmenau : Universitätsbibliothek, 2020. - 1 Online-Ressource (XVIII, 144 Blätter, Blatt XIX-XLVIII)
Technische Universität Ilmenau, Dissertation 2020

Im Zuge neuer EU-Direktiven wurde die Verwendung von Cr(VI)-Verbindungen stark reglementiert. In der Oberflächentechnik wurde daraufhin sechswertiges Chrom durch sicherere und gleichzeitig effektive Passivierungen auf Cr(III)-Basis ersetzt. Der Korrosionsschutz von Cr(VI)-Beschichtungen ohne Wärmebehandlung ist im Allgemeinen besser. In bisher durchgeführten Untersuchungen zeigte sich, dass durch Zusatz von Übergangsmetallionen der Korrosionsschutz der Cr(III)-Passivierungsschicht verbessert werden kann. In dieser Arbeit wird der Einfluss der Zusammensetzung von Cr(III)-Passivierung mit Kobaltanteil auf die Bildung und die Struktur von Konversionsschichten auf verzinkten Substraten untersucht. Auf den verzinkten Stahl wurden Modelllösungen mit zwei verschiedenen Komplexbildnern, nämlich Fluorid und Oxalat, mit und ohne Kobalt aufgetragen. Rasterelektronenmikroskopie (REM) und Rasterkraftmikroskopie zeigten Oberflächenmorphologien mit mikrostrukturellen Defekten. In Anwesenheit von Kobalt wurden die Schichten gleichmäßiger. Die elementare Zusammensetzung der Schichten wurde mit der Augerelektronenspektroskopie (AES) untersucht. Die Mengen an Cr und Co in den Beschichtungen wurden mit Hilfe der optischen Plasma-Emissionsspektroskopie (ICP-OES) bestimmt. Sowohl AES als auch ICP-OES zeigten Co-Gehalte in den Schichten. Mit Hilfe eines thermodynamischen Modells wurde die Konzentration von Cr(III)-, Zn(II)- und Co(II)-Spezies in der Behandlungslösung im pH-Bereich von 0,0 bis 14,0 und auch der minimale pH-Wert für die Abscheidung der Metallionen in der entsprechenden Lösung berechnet. Die Ergebnisse der Korrosionstests (Polarisationsmessung und elektrochemische Impedanzspektroskopie) legen nahe, dass die Bildung einer dichten Schicht für eine gute Korrosionsbeständigkeit entscheidend ist. Außerdem wurde der Bildungsmechanismus von Cr(VI) in den Schichten untersucht. Die Anwesenheit von Cr(VI) wurde mittels Spektrophotometrie nachgewiesen. Die Morphologie und Struktur der Filme wurden per REM beobachtet. Die Gesamtwassermenge in den Schichten wurde mittels Karl-Fischer-Titration gemessen. Es zeigte sich, dass die Morphologie des fluoridhaltigen Films mit einer hohen Dichte an Mikroporen die Wahrscheinlichkeit eines Wassereinschlusses erhöht. Dies führte zu einer Oxidation von Cr(III) zu Cr(VI) durch Sauerstoff in Gegenwart von Wasser bei erhöhten Temperaturen.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2020000368
Wang, Hongmei; Xiong, Jie; Cheng, Xing; Fritz, Mathias; Ispas, Adriana; Bund, Andreas; Chen, Ge; Wang, Dong; Schaaf, Peter
Ni3N-coated Ni nanorod arrays for hydrogen and oxygen evolution in electrochemical water splitting. - In: ACS applied nano materials, ISSN 2574-0970, Bd. 3 (2020), 11, S. 10986-10995
Im Titel ist "3" tiefgestellt

Designing high efficiency non-noble metal catalysts for electrochemical hydrogen and oxygen evolution reactions (HER and OER) is a challenging and promising task. In the present work, a large-scale self-supported black nickel sheet composed of nickel nanorod arrays (B-Ni) was successfully fabricated via electroplating with a nanostructured Si template assisted strategy, and Ni3N coating layer was coated on the structured surface followed by a nitrogen plasma treatment with different treatment durations. The black color is due to the immensely enhanced light absorption through the surface nanostructures with high aspect ratio. The samples show promising catalytic performance when used as electrochemical catalysts for both HER and OER in alkaline electrolyte. Benefiting from the nanostructure and the Ni3N coating, B-Ni_N2_10 min exhibits low onset potentials of 1.560 and 0.165 V at a current density of 10 mA/cm2 for OER and HER, respectively. The calculated electrochemical surface area (ECSA) for B-Ni is 10 times higher than the pristine Ni sheet (P-Ni), while after nitrogen plasma treatment, the ECSA for B-Ni_N2_10 min is 21 times higher than that of the P-Ni. In addition, all the catalysts show good electrochemical stabilities. All the improvements for the electrochemical performances suggest that nanostructured nickel nitride could be a promising inexpensive catalyst system for both OER and HER processes.



https://doi.org/10.1021/acsanm.0c02222
Kostetzer, Lucas; Nebl, Christoph; Stich, Michael; Bund, Andreas; Schweiger, Hans-Georg
Physics-based modeling and parameter identification for lithium ion batteries under high current discharge conditions. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Volume 167 (2020), number 14, 140549

Extreme scenarios of high discharge current must be understood for better battery management system design. Physics-based modeling can give a better insight into the battery response but can be challenging due to the large number of parameters. In this work, an electrochemical pseudo-2D model is developed and used in the parameter identification and validated under high current discharge conditions. Commercial 18650 cells with maximum rated current of 20 A (13.3 C) are characterized with discharge rates up to 40 C under controlled thermal conditions. The proposed three-step parameter identification procedure starts with the open circuit voltage being used to estimate the equilibrium potentials. In a second step, kinetic parameters are identified under high current aided by a parameter sensitivity analysis and parameter optimization with an evolutionary algorithm. The third step is the verification by comparing simulation results with measurements resulting in root main square error under 89 mV for currents until 26.6 C. Limits of the model are explored in the 33.3 C case, where a parameter re-fit shows that polarization effects change for very high current.



https://doi.org/10.1149/1945-7111/abc726
Bund, Andreas; Ispas, Adriana; Ivanov, Svetlozar; Engemann, Thomas; Endrikat, Anna
New electroplating processes from ionic liquids (GALACTIF) : subproject: Deposition of pure and alloyed refractory metals from ionic liquids
Verbundname: Neue galvanotechnische Beschichtungsprozesse aus ionischen Flüssigkeiten (GALACTIF); Teilvorhaben: Abscheidung von reinen und legierten Refraktärmetallschichten aus ionischen Flüssigkeiten : Laufzeit des Vorhabens: 01.06.2016-29.02.2020, Berichtzeitraum: 01.06.2016-29.02.2020. - Ilmenau : [Technische Universität Ilmenau, Fachgebiet Elektrochemie und Galvanotechnik]. - 1 Online-Ressource (69 Seiten, 4,26 MB)Förderkennzeichen BMBF 13XP5017F

https://doi.org/10.2314/KXP:1736013130
Dani, Olfa; Kurniawan, Mario; Paszuk, Agnieszka; Nandy, Manali; Bund, Andreas; Hannappel, Thomas
InP(100) surfaces for efficient photoelectrochemical water splitting. - In: DPG-Frühjahrstagung (DPG Spring Meeting) of the Condensed Matter Section (SKM) together with the DPG Division Environmental Physics and the Working Groups Accelerator Physics; Equal Opportunities; Energy; Industry and Business; Physics, Modern IT and Artificial Intelligence, Young DPG, (2020), HL 34.2

Vedel, Elena; Olfa, Dani; Kurniawan, Mario; Pflug, Theo; Kürth, Sascha; Hill, Noah; Espinoza, Shirly; Rebarz, Mateusz; Olbrich, Markus; Herrfurth, Oliver; Krischok, Stefan; Horn, Alexander; Andreasson, Jakob; Schmidt-Grund, Rüdiger; Bund, Andreas; Hannappel, Thomas
Surface modification and charge carrier dynamics of materials and structures for semiconductor-based solar water splitting applications under operation conditions. - In: DPG-Frühjahrstagung (DPG Spring Meeting) of the Condensed Matter Section (SKM) together with the DPG Division Environmental Physics and the Working Groups Accelerator Physics; Equal Opportunities; Energy; Industry and Business; Physics, Modern IT and Artificial Intelligence, Young DPG, (2020), HL 75.25

Mulyaningsih, Sri; Klemke, Bastian; Siemensmeyer, Konrad; Fritz, Mathias; Kurniawan, Mario; Ispas, Adriana; Bund, Andreas
Influence of thermal treatment on the magnetic properties and morphology of electrodeposited Fe-Co films. - In: Journal of magnetism and magnetic materials, ISSN 1873-4766, Bd. 513 (2020), 167204

Fe-Co films were prepared by electrodeposition from an electrolyte containing citric acid and annealed afterwards at different temperatures up to 700 ˚C. The grain sizes of the deposits increased from 11 nm to 30 nm with increasing annealing temperature, which lead to changes in magnetic properties of deposits. SQUID measurements indicate that there is a difference between the coercive force, Hc, of the as deposited samples (17 Oe) and the heat-treated samples (25-40 Oe) with a measurement error of 1-2 Oe. The remnant magnetization, Mr, decreased from 190 ± 12 emu/cm^3 for the as deposited to 75 ± 5 emu/cm^3 for the annealed samples, respectively. The saturation magnetization, Ms, seems not to be influenced strongly by the thermal treatment, with the only exception for the samples annealed at 500 ˚C. Thus, Ms has a slightly decreasing tendency from 1880 ± 90 emu/cm^3 for the as-deposited samples to 1780 ± 85 emu/cm^3 for samples annealed at 700 ˚C. The biggest value for Ms (2100 ± 105 emu/cm^3) was obtained if the samples were annealed at 500 ˚C. The thermal treatment generated cracks in the deposits. Interestingly, these cracks had a regular rectangular shape only if the deposits were annealed at 600 ˚C. The coercivity of the layers annealed at 600 ˚C was lower compared to layers annealed at the other temperatures. Magnetic force microscopy measurements indicated the magnetic domain distribution and the topography of the annealed deposits. The deposits showed the best soft magnetic properties if annealed between 500 and 600 ˚C.



https://doi.org/10.1016/j.jmmm.2020.167204
Wang, Qiang; Wang, Haijiang; Cheng, Xiaopeng; Fritz, Mathias; Wang, Dong; Li, Hao; Bund, Andreas; Chen, Ge; Schaaf, Peter
NiCo2O4Ni2P nanorods grown on nickel nanorod arrays as a bifunctional catalyst for efficient overall water splitting. - In: Materials today, ISSN 2468-6069, Bd. 17 (2020), 100490

The development of efficient and durable non-noble metal catalysts remains a challenge in electrocatalytic water splitting applications. To address this, a bifunctional catalyst involving hierarchical NiCo2O4Ni2P nanorods grown on nickel nanorod arrays (NiCo2O4@Ni2P/NAs) was designed and fabricated in this study for overall water splitting that provided high activity and acceptable stability. And if used as the cathode and anode in alkaline media, the NiCo2O4@Ni2P/NAs only required 1.58 V to achieve a current density of 10 mA cm^-2, which is superior to most reported catalysts and can be attributed to a unique core-shell structure and coexisting crystalline/amorphous Ni2P phases.



https://doi.org/10.1016/j.mtener.2020.100490
Gong, Qing; Ding, Wenjin; Bonk, Alexander; Li, Haomiao; Wang, Kangli; Jianu, Adrian; Weisenburger, Alfons; Bund, Andreas; Bauer, Thomas
Molten iodide salt electrolyte for low-temperature low-cost sodium-based liquid metal battery. - In: Journal of power sources, ISSN 1873-2755, Bd. 475 (2020), 228674

Using low-melting-point electrolytes could overcome various key challenges of low-cost sodium-based liquid metal batteries (Na-LMBs), e.g. high rates of self-discharge and degradation of structural materials, by lowering their operating temperatures. Molten halide salts are considered promising electrolyte candidates for Na-LMBs due to their high stability and electrical conductivity. In this work, thermodynamic simulation via FactSageTM and thermal analysis via e.g. Differential Scanning Calorimeter (DSC) were carried out to explore the NaI-LiI-KI system, since it could be a promising electrolyte for Na-LMBs due to its low melting point and Na solubility. The results show that the eutectic NaI-LiI-KI performs as a pseudo-binary salt with a melting point of ˜290 &ring;C. In this pseudo-binary salt, the solubility of NaI in the eutectic LiI-KI is ˜7 mol%. Using the eutectic NaI-LiI-KI electrolyte, Na-LMBs could be operated at < 350 &ring;C. Moreover, the Na solubility and Na+ conductivity of the eutectic NaI-LiI-KI electrolyte, which are vital to the battery performance, were estimated by calculation based on the literature data. Additionally, its applicability and economy were also discussed based on cost pre-analysis of salt materials, salt treatment and structural materials regarding salt corrosivity.



https://doi.org/10.1016/j.jpowsour.2020.228674
Gruia, Violeta-Tincuta; Ispas, Adriana; Efimov, Igor; Bund, Andreas
Cation exchange behavior during the redox switching of poly (3,4-ethylenedioxythiophene) films. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 24 (2020), 11/12, S. 3231-3244

Poly (3,4-ethylenedioxythiophene), PEDOT, films were synthesized at room temperature by potentiodynamic and potentiostatic step deposition in aqueous solutions containing EDOT monomer and LiClO4. In some solutions, the effect of small amounts of sodium dodecylsulfate, SDS, on the polymerization rate of EDOT and on the stiffness of the obtained PEDOT film was studied. The obtained PEDOT films were transferred in aqueous solutions containing cations with different molar mass, such as H+, Li+, Na+, K+, and Cs+. The apparent molar masses of the exchanged species during potentiodynamic experiments were determined by in situ microgravimetry. These measurements underlined the importance of the electrolyte chosen for electropolymerization process. It is known that SDS anions can be trapped inside the polymer layer during electropolymerization, providing them with a cation exchange behavior. However, even if the PEDOT films were deposited from an electrolyte without SDS, they still acted as cation exchangers.



https://doi.org/10.1007/s10008-020-04809-6
Borissenko, Natalia; Ispas, Adriana; Wu, Qiong; Carstens, Timo; Behrens, Niklas; Karg, Julian; Engemann, Thomas; Endrikat, Anna; Bund, Andreas; Endres, Frank
Electrocodeposition of titanium and gallium from 1-butyl-1-methylpyrrolidiniumtrifluoromethanesulfonate. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Volume 167 (2020), number 12, 122512

Electrochemical co-deposition of gallium and titanium on copper and gold substrates from the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate was investigated in the temperature range from 25 &ring;C to 140 &ring;C. Crystalline gallium-titanium alloys were obtained by annealing the deposits at 800 &ring;C for 16 h. X-ray diffraction performed on the annealed specimens confirmed the formation of crystalline phases. In situ quartz crystal microbalance experiments gave further insight into the initial stages of gallium-titanium co-deposition. One can tune the composition of the films by changing the deposition potential or the deposition technique. Gallium rich films with more than 60 wt% were obtained by potentiostatic depositions at 140 &ring;C. We could show that no elemental titanium can be electrodeposited from bis(cyclopentadienyl)titanium(IV) bis(trifluoromethanesulfonate) in 1-butyl-1-methyl- pyrrolidinium trifluoromethanesulfonate. The addition of GaCl 3 to the electrolyte facilitated the reduction of Ti(IV) species.



https://doi.org/10.1149/1945-7111/abb27f
Kovácsovics, Iris; Patzelt, Thomas; Pilz, Uwe; Herrmann, Johannes; Bund, Andreas
Numerical simulation of copper deposition in the Hull cell based on Butler-Volmer kinetics. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Volume 167 (2020), number 12, 122506

In industry plating baths are often characterized by visual evaluation of a Hull cell deposition. In an academic approach, kinetic parameters are determined with cyclic voltammetry to obtain a deeper understanding of reaction mechanisms. In this paper we combine both approaches and show how via numerical simulations based on the boundary element method kinetic parameters can be extracted from Hull cell experiments. This combined method enables a better understanding of industrial electroplating processes without losing important information about coating and visual appearance. The validation is done in an acidic copper system using the kinetic parameters obtained from cyclic voltammetry for simulating the current density distribution and the cell voltage of a Hull cell deposition, followed by a comparison with experimental data. As an additional insight obtained from this study, the presence of O2 lowers the anodic transfer coefficient, while Cl- ions in the electrolyte increase the exchange current density.



https://doi.org/10.1149/1945-7111/abb1d5
Gabryelczyk, Agnieszka; Ivanov, Svetlozar; Bund, Andreas; Lota, Grzegorz
Taguchi method in experimental procedures focused on corrosion process of positive current collector in lithium-ion batteries. - In: Electrochimica acta, ISSN 1873-3859, Bd. 360 (2020), 137011

Planning the design and discussing the results are routine tasks carried out daily by researchers all over the world. This study is focused on making these stages of research time- and cost-efficient without affecting the reliability of the data. Following the principles of the Taguchi method brings such a result. This approach ensures the quality of research by optimisation of the experimental procedure. In the presented work, the Taguchi method solves an exemplary research problem of the corrosion process of aluminium current collector in lithium-ion batteries. Operating factors selected for the optimisation include temperature (25, 35, 45&ring;C), the volume ratio of ethylene carbonate to diethyl carbonate in the solvent (1:1, 1:2, 1:4), and type of lithium salt (LiPF6, LiTFSI, LiBOB). Using three operating factors with three levels of variability requires data assembly in an orthogonal array L9 with nine experimental runs in total. In this study, the Taguchi approach is validated by performing a full-factorial procedure of twenty-seven individual experiments. The response of tested systems is analysed by cyclic voltammetry and electrochemical impedance spectroscopy, which enables the evaluation of corrosion parameters in each experimental run. The assessed parameters indicate the intensity of the aluminium corrosion depending on the operating conditions. These conditions cause unwanted variance, which accelerates corrosion and lowers the life expectancy of lithium-ion batteries. The Taguchi signal-to-noise-ratio analysis reveals that the most significant variation is caused by the lithium salt in the electrolyte (S/N LiBOB ≥ LiPF6 > LiTFSI). Temperature and alkyl carbonates play a secondary role. The Taguchi prediction method is also consistent with the full-factorial approach, which warrants reliability.



https://doi.org/10.1016/j.electacta.2020.137011
Böttcher, René; Mai, Sebastian; Ispas, Adriana; Bund, Andreas
Aluminum deposition and dissolution in [EMIm]Cl-based ionic liquids-kinetics of charge-transfer and the rate-determining step. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Volume 167 (2020), number 10, 102516, 8 Seiten

https://doi.org/10.1149/1945-7111/ab9c84
Chernyakova, Katsiaryna; Ispas, Adriana; Karpicz, Renata; Ecke, Gernot; Vrublevsky, Igor; Bund, Andreas
Formation of ordered anodic alumina nanofibers during aluminum anodizing in oxalic acid at high voltage and electrical power. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 394 (2020), 125813

https://doi.org/10.1016/j.surfcoat.2020.125813
Hadzich, Antonella; Groß, Gregor Alexander; Leimbach, Martin; Ispas, Adriana; Bund, Andreas; Flores, Santiago
Effect of polyalcohols on the anticorrosive behaviour of alkyd coatings prepared with drying oils. - In: Progress in organic coatings, Bd. 145 (2020), 105671

https://doi.org/10.1016/j.porgcoat.2020.105671
Ivanov, Svetlozar; Sauerteig, Daniel; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Irreversible dilation of graphite composite anodes influenced by vinylene carbonate. - In: Journal of power sources, ISSN 1873-2755, Bd. 457 (2020), 228020

https://doi.org/10.1016/j.jpowsour.2020.228020
Manjum, Marjanul; Serizawa, Nobuyuki; Ispas, Adriana; Bund, Andreas; Katayama, Yasushi
Electrochemical preparation of Cobalt-Samarium nanoparticles in an aprotic ionic liquid. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Volume 167 (2020), number 40, 042505, 8 Seiten

https://doi.org/10.1149/1945-7111/ab79a8
Deich, Tobias; Hahn, Severin Lukas; Both, Svenja; Birke, Peter; Bund, Andreas
Validation of an actively-controlled pneumatic press to simulate automotive module stiffness for mechanically representative lithium-ion cell aging. - In: Journal of energy storage, ISSN 2352-152X, Bd. 28 (2020), 101192

https://doi.org/10.1016/j.est.2020.101192
Leimbach, Martin; Tschaar, Christoph; Schmidt, Udo; Bund, Andreas
Low-frequency pulse plating for tailoring the optical appearance of chromium layers for decorative applications. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 50 (2020), 4, S. 489-499

https://doi.org/10.1007/s10800-020-01406-3
Vlaic, Codruta Aurelia; Kurniawan, Mario; Peipmann, Ralf; Lal&bovko;au, Cornel-Constantin; Stich, Michael; Schmidt, Udo; Bund, Andreas
Improved wear resistance of alternating amorphous and crystalline layers in electrodeposited NiP multilayers. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 386 (2020), 125470, S. 1-8

https://doi.org/10.1016/j.surfcoat.2020.125470
Hadzich, Antonella; Groß, Gregor Alexander; Leimbach, Martin; Ispas, Adriana; Bund, Andreas; Flores, Santiago
Characterization of Plukenetia volubilis L. fatty acid-based alkyd resins. - In: Polymer testing, ISSN 1873-2348, Bd. 82 (2020), 106296

https://doi.org/10.1016/j.polymertesting.2019.106296
Schötz, Theresa; Craig, Ben; Ponce de Leon, Carlos; Bund, Andreas; Ueda, Mikito; Low, Chee Tong John
Aluminium-poly(3,4-ethylenedioxythiophene) rechargeable battery with ionic liquid electrolyte. - In: Journal of energy storage, ISSN 2352-152X, Bd. 28 (2020), 101176, insges. 9 S.

https://doi.org/10.1016/j.est.2019.101176
Link, Steffen; Ivanov, Svetlozar; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Understanding the initial stages of Si electrodeposition under diffusion kinetic limitation in ionic liquid-based electrolytes. - In: Journal of crystal growth, Bd. 531 (2020), 125346, S. 1-6

https://doi.org/10.1016/j.jcrysgro.2019.125346
Behúl, Miroslav; Vojs, Marian; Marton, Marián; Michniak, Pavol; Mikolášek, Miroslav; Kurniawan, Mario; Honig, Hauke; Zyabkin, Dmitry; Oliva Ramírez, Manuel; Spieß, Lothar; Flock, Dominik; Bund, Andreas; Papula, Martin; Redhammer, Robert
Nanostructured boron doped diamond enhancing the photoelectrochemical performance of TiO2/BDD heterojunction anodes. - In: Vacuum, ISSN 0042-207X, Volume 171 (2020), 109006, Seite 1-5
Im Titel ist "2" tiefgestellt

https://doi.org/10.1016/j.vacuum.2019.109006
Böttcher, René; Ispas, Adriana; Bund, Andreas
Anodic dissolution of aluminum and anodic passivation in [EMIm]Cl-based ionic liquids. - In: Electrochemistry communications, ISSN 1873-1902, Bd. 115 (2020), 106720, S. 1-6

https://doi.org/10.1016/j.elecom.2020.106720
Kurniawan, Mario;
Galvanische Herstellung freistehender poröser Kupferschichten. - In: ZVO-Report, (2019), 5, S. 56

Dennstädt, Florian;
Optimierung der galvanischen Abscheidung von funktionellen Nickelschichten. - In: ZVO-Report, (2019), 2, S. 46

Groß, Philipp; Ihlow, Alexander; Böttcher, René; Bessert, Steffen; Pandey, Rick; Kirchhof, Jan; Krieg, Fabian; Römer, Florian; Osman, Ahmad; Del Galdo, Giovanni
Ein portabler, vielfältig einsetzbarer 3D-Positionierer für Synthetik-Apertur-Ultraschallmessungen in der ZfP. - In: DACH-Jahrestagung 2019, (2019), insges. 2 S.
Paper P41

Böttcher, René; Endrikat, Anna; Engemann, Thomas; Fritz, Mathias; Gruia, Violeta-Tincuta; Hesamedini, Sanaz; Ispas, Adriana; Leimbach, Martin; Schmidt, Udo; Sottor, Robert; Bund, Andreas
Elektrochemische Oberflächentechnik. - In: Dialog, ISSN 2193-3383, (2019), 3, S. 16-21

Ispas, Adriana; Schlag, Leslie; Eggert, Lara; Böttcher, René; Bund, Andreas; Jacobs, Heiko O.
Electrodeposition of aluminium-nickel films in 1-butyl-1-methylpyrrolidinium-bis(trifluoromethylsulfonyl) amide. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2019-02 (2019), 17, 963

https://doi.org/10.1149/MA2019-02/17/963
Stimming, Ulrich; Wang, Jiabin; Bund, Andreas
The vanadium redox reactions - electrocatalysis versus non-electrocatalysis. - In: ChemPhysChem, ISSN 1439-7641, Bd. 20 (2019), 22, S. 3004-3009

https://doi.org/10.1002/cphc.201900861
Dyck, Tobias; Bund, Andreas
Investigations on the DC current distribution in stranded wires and relevance for temperature tests :
Untersuchungen zur DC-Stromverteilung in feindrähtigen Leitern und die Bedeutung für Stromerwärmungsprüfungen. - In: Kontaktverhalten und Schalten, (2019), S. 39-48

Es wird eine Methode zur Untersuchung der Stromverteilung in Kupferleitern vorgestellt. Zur Auswertung der Stromverteilung wird mit Hall-Sensoren die magnetische Flussdichte gemessen. Eindrähtige Leiter zeigen eine gleichmäßige Stromverteilung. Die Stromverteilung von Litzenleitern ist inhomogen, da im Inneren des Leiters zusätzliche elektrische Widerstände auftreten. Die Höhe der inneren Kontaktwiderstände hängt maßgeblich von der Oberflächenbeschaffenheit der Kupferdrähte ab, so führen Verunreinigungen und Korrosionsschichten zu einem Anstieg der inneren Widerstände und damit zu einer inhomogeneren Stromverteilung. Durch Kontaktwiderstandsmessungen und Stromerwärmungsprüfungen wird der Einfluss von Fremdschichten auf die Kontaktqualität von feindrähtigen Leitern untersucht. Das Crimpen des Leiterendes führt zu einer Homogenisierung der Stromverteilung.



Baumer, Christoph; Bund, Andreas; Herrmann, Johannes
A predictive model for the time dependence of concentrations in plating baths. - In: Journal of chemometrics, ISSN 1099-128X, Bd. 33 (2019), 9, S. e3166, insges. 8 S.

https://doi.org/10.1002/cem.3166
Seidl, Lukas; Carstens, Timo; Endrikat, Anna; Engemann, Thomas; Egger, Christiane; Manolova, Mila; Moustafa, Essam; Scharf, Ingolf; Yesilbas, Göktug; Eke, Esther; Martens, Sladjana; Asen, Ludwig; Fischer, Pauline; Ispas, Adriana; Peipmann, Ralf; Ivanov, Svetlozar; Wu, Qiong; Behrens, Niklas; Borisenko, Natalia; Höhlich, Dominik; Dietz, Andreas; Böck, Reinhard; Bund, Andreas; Kühn, Fritz; Lampke, Thomas; Endres, Frank; Schneider, Oliver
Neue galvanotechnische Beschichtungsprozesse aus ionischen Flüssigkeiten. - In: WOMag, ISSN 2195-5891, Bd. 8 (2019), 9, S. 34-36

Engemann, Thomas; Endrikat, Anna; Ispas, Adriana; Bund, Andreas
Electrodeposition of refractory metal alloys by ionic liquids :
Elektrochemische Abscheidung von Refraktärmetalllegierungen aus ionischen Flüssigkeiten. - In: WOMag, ISSN 2195-5891, Bd. 8 (2019), 9, S. 30-32

Böttcher, René; Ispas, Adriana; Bund, Andreas
Elektrochemische Abscheidung von Aluminium und Aluminiumlegierungen aus ionischen Flüssigkeiten. - In: WOMag, ISSN 2195-5891, Bd. 8 (2019), 9, S. 25-27

Endrikat, Anna; Borisenko, Natalia; Ispas, Adriana; Peipmann, Ralf; Endres, Frank; Bund, Andreas
Electrochemical reduction mechanism of NbF5 and NbCl5 in the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate. - In: Electrochimica acta, ISSN 1873-3859, Bd. 321 (2019), 134600, S. 1-15
Im Titel ist "5" tiefgestellt

https://doi.org/10.1016/j.electacta.2019.134600
Chang, Yali; Wang, Min; Wang, Shengping; Na, Jongbeom; Bund, Andreas; Nanjundan, Ashok Kumar; Yamauchi, Yusuke
Ultralong storage life of Li/MnO2 primary batteries using MnO2-(CFx)n with C-F semi-ionic bond as cathode materials. - In: Electrochimica acta, ISSN 1873-3859, Bd. 320 (2019), 134618, S. 1-9
Im Titel sind "2", "x" und "n" tiefgestellt

https://doi.org/10.1016/j.electacta.2019.134618
Bartsch, Heike; Peipmann, Ralf; Himmerlich, Marcel; Müller, Jens; Bund, Andreas; Witte, Hartmut
PEDOT coating applied on thick film gold electrodes for increased miniaturization capability. - In: Progress in organic coatings, Bd. 135 (2019), S. 545-554

https://doi.org/10.1016/j.porgcoat.2019.06.023
Kaltwasser, Mahsa; Schmidt, Udo; Lösing, Lars; Biswas, Shantonu; Stauden, Thomas; Bund, Andreas; Jacobs, Heiko O.
Fluidic self-assembly on electroplated multilayer solder bumps with tailored transformation imprinted melting points. - In: Scientific reports, ISSN 2045-2322, Bd. 9 (2019), 11325, S. 1-8

https://doi.org/10.1038/s41598-019-47690-8
Böttcher, René; Valitova, Alina; Ispas, Adriana; Bund, Andreas
Electrodeposition of aluminium from ionic liquids on high strength steel. - In: Transactions of the Institute of Metal Finishing, ISSN 1745-9192, Bd. 97 (2019), 2, S. 82-88

https://doi.org/10.1080/00202967.2019.1573941
Bund, Andreas; Link, Steffen; Ivanov, Svetlozar
Electrochemical deposition of silicon from organic electrolytes. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, (2019), S. 1-14

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT6610
Stich, Michael; Fritz, Mathias; Roscher, Michael; Peipmann, Ralf
Korrosionsverhalten von bipolaren Stromableitern für Lithium-Ionen-Batterien, (Teil 2). - In: Galvanotechnik, ISSN 0016-4232, Bd. 110 (2019), 1, S. 67-73

Hesamedini, Sanaz; Bund, Andreas
Trivalent chromium conversion coatings. - In: Journal of coatings technology and research, ISSN 1935-3804, Bd. 16 (2019), 3, S. 623-641

https://doi.org/10.1007/s11998-019-00210-9
Xu, Yinsheng; Wang, Shengping; Peng, Huiling; Yang, Zhigao; Martin, Darren J.; Bund, Andreas; Nanjundan, Ashok Kumar; Yamauchi, Yusuke
Electrochemical characteristics of cobaltosic oxide in organic electrolyte according to bode plots: double-layer capacitance and pseudocapacitance. - In: ChemElectroChem, ISSN 2196-0216, Bd. 6 (2019), 9, S. 2456-2463

https://doi.org/10.1002/celc.201900289
Bengoa, Leandro N.; Ispas, Adriana; Bengoa, José Fernando; Bund, Andreas; Egli, Walter A.
Ultrasound assisted electrodeposition of Cu-SiO2 composite coatings: effect of particle surface chemistry. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 166 (2019), 8, Seite D244-D251
Im Titel ist "2" tiefgestellt

https://doi.org/10.1149/2.0181908jes
Leimbach, Martin; Tschaar, Christoph; Zapf, David; Kurniawan, Mario; Schmidt, Udo; Bund, Andreas
Relation between color and surface morphology of electrodeposited chromium for decorative applications. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 166 (2019), 6, Seite D205-D211

https://doi.org/10.1149/2.0871906jes
Stich, Michael;
Wasserverunreinigungen in Lithium-Ionen-Batterien. - Ilmenau : Universitätsbibliothek, 2019. - 1 Online-Ressource (III, 94 Seiten, Seite V-XXXV)
Technische Universität Ilmenau, Dissertation 2019

Lithium-Ionen Batterien (LIB) verwenden organische Elektrolyte, die auch bei hohen Spannungen von über 4 V stabil sind. Das Leitsalz, das für die meisten Elektrolyten genutzt wird, ist LiPF6. Dieses hat eine Reihe an positiven Eigenschaften, wie eine hohe Leitfähigkeit und chemische Stabilität, ist aber hydrolyseempfindlich. Die Hydrolyseprodukte können zu einer verringerten Batterieperformance und Zyklenstabilität sowie - im Falle einer Elektrolytleckage - zu Gesundheitsrisiken führen. Diese Arbeit untersucht deshalb, welche Materialien zu den Wasserverunreinigungen in einer LIB beitragen, wie die Wasserverunreinigungen mit LiPF6 reagieren und was die Effekte dieser Verunreinigungen auf das elektrochemische Verhalten der LIB sind. Das Trocknungsverhalten von Zellkomponenten wurde mittels Karl-Fischer Titration untersucht und zeigt, dass insbesondere das Anodenmaterial Graphit und der Glasfaserseparator eingehend getrocknet werden müssen, um einen Wassereintrag in die LIB zu minimieren. Unter den Kathodenmaterialien weist insbesondere LiFePO4 einen hohen Wassergehalt auf. Andere Zellkomponenten sind weniger hygroskopisch und können einfacher getrocknet werden, was bei der industriellen LIB Herstellung mit einer Kostenreduktion verbunden ist. Die Hydrolyse von LiPF6 wurde durch Ionenchromatographie im organischen Lösungsmittel EC/DEC (1:1 v/v) und in Wasser untersucht. Die Hydrolyseprodukte von LiPF6 in EC/DEC sind HF und HPO2F2. Um die komplexen Reaktionskinetiken zu untersuchen, wurde ein kinetisches Model erstellt, mit dem Vorhersagen über weniger hydrolyseempfindliche Elektrolyten möglich sind. Insbesondere zeigt sich, dass der Dissoziationsgrad eine große Rolle in der Hydrolyse von LiPF6 im spezifischen Lösungsmittel spielt, und ein höherer Dissoziationsgrad zu einer höheren Toleranz gegenüber Wasserverunreinigungen führt. Wasserverunreinigungen haben negative Effekte auf die Zyklenstabilität und führen zu einem erhöhten Ladungsübergangswiderstand, was auf eine veränderte SEI-Formierung und Zusammensetzung hindeutet. Die Erklärung wird auch durch die Erkenntnis gestützt, dass die coulombsche Effizienz im ersten Zyklus bei wasserkontaminierten Zellen niedriger ist. Diese Ergebnisse verdeutlichen, wie wichtig eine Limitierung und Kontrolle der Wasserkontamination in LIB für deren Langlebigkeit, Performance und Sicherheit ist.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2019000089
Link, Steffen; Ivanov, Svetlozar; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Electrochemical deposition of silicon from a sulfolane-based electrolyte: effect of applied potential. - In: Electrochemistry communications, ISSN 1873-1902, Bd. 103 (2019), S. 7-11

https://doi.org/10.1016/j.elecom.2019.04.008
Dyck, Tobias; Adler, Marius; Bund, Andreas
Investigation of conductor packages and contact geometries for stranded copper wires. - In: IEEE transactions on components, packaging and manufacturing technology, ISSN 2156-3985, Bd. 9 (2019), 3, S. 399-404

https://doi.org/10.1109/TCPMT.2019.2893678
Ivanov, Svetlozar; Mai, Sebastian; Himmerlich, Marcel; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Microgravimetric and spectroscopic analysis of solid-electrolyte interphase formation in presence of additives. - In: ChemPhysChem, ISSN 1439-7641, Bd. 20 (2019), 5, S. 655-664

https://doi.org/10.1002/cphc.201801001
Mai, Sebastian; Wessel, Janine; Dimitrova, Anna; Stich, Michael; Ivanov, Svetlozar; Krischok, Stefan; Bund, Andreas
Nanoscale morphological changes at lithium interface, triggered by the electrolyte composition and electrochemical cycling. - In: Journal of chemistry, ISSN 2090-9071, (2019), Article ID 4102382, insges. 13 S.

https://doi.org/10.1155/2019/4102382
Bartsch, Heike; Peipmann, Ralf; Himmerlich, Marcel; Frant, Marion; Rothe, Holger; Liefeith, Klaus; Witte, Hartmut
Surface properties and biocompatibility of thick film materials used in ceramic bioreactors. - In: Materialia, ISSN 2589-1529, Volume 5 (2019), article 100213, 7 Seiten

https://doi.org/10.1016/j.mtla.2019.100213
Büker, Lisa;
Komplexierungsverhalten von dreiwertigem Chrom mit Carbonsäuren. - In: ZVO-Report, (2018), 5, S. 59

Gruia, Violeta-Tincuta;
Galvanische Abscheidung von dekorativem, dunklem Chrom aus Chrom(III)-Elektrolyten. - In: ZVO-Report, (2018), 3, S. 91

Hesamedini, Sanaz;
Bildungsmechanismus von sechswertigem Chrom auf dreiwertigen Chrom-Passivschichten. - In: ZVO-Report, (2018), 1, S. 54

Schötz, Theresa; Ponce De León, Carlos; Bund, Andreas; Ueda, Mikito
Interaction of 3D conductive polymer-reticulated vitreous carbon composites in ionic liquid as energy storage material. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 53, 1882

https://doi.org/10.1149/MA2018-02/53/1882
Lucero Lucas, Gisella Liliana; Gruia, Violeta-Tincuta; Ispas, Adriana; Bund, Andreas
Development of an electrochemical sensor for the detection of dopamine based on PEDOT and silver nanoparticles. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 55, 1981

https://doi.org/10.1149/MA2018-02/55/1981
Fritz, Mathias; Bund, Andreas; Ullrich, Hans-Jürgen
A novel photoelectrochemical approach to fight biofilms and reduce undesired microbiology. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 27, 897

https://doi.org/10.1149/MA2018-02/27/897
Böttcher, René; Ispas, Adriana; Bund, Andreas
Corrosion behavior of aluminum alloys deposited from ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 12, 634

https://doi.org/10.1149/MA2018-02/12/634
Leimbach, Martin; Tschaar, Christoph; Schmidt, Udo; Bund, Andreas
Characterization of chromium deposition from trivalent solutions by EQCM and near-surface pH measurements. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 12, 641

https://doi.org/10.1149/MA2018-02/12/641
Camargo, Magali K.; Übel, Martin; Kurniawan, Mario; Ziegler, Ferdinand; Schmidt, Udo; Barz, Andrea; Bliedtner, Jens; Bund, Andreas
Surface activation of polymers assisted by picosecond laser pulses for selective metallization via electroless deposition. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2018-02 (2018), 21, 788

https://doi.org/10.1149/MA2018-02/21/788
Ivanov, Svetlozar;
Novel materials and advanced analytical techniques for application in Li-ion battery research and technology. - Ilmenau. - 1 Band (verschiedene Seitenzählungen)
Technische Universität Ilmenau, Habilitationsschrift 2019


Stich, Michael; Fritz, Mathias; Roscher, Michael; Peipmann, Ralf
Korrosionsverhalten von bipolaren Stromableitern für Lithium-Ionen-Batterien, (Teil 1). - In: Galvanotechnik, ISSN 0016-4232, Bd. 109 (2018), 12, S. 2330-2336

Dyck, Tobias; Bund, Andreas
The influence of contaminated copper wires on the DC joule heating of connectors. - In: Electrical contacts - 2018, (2018), S. 17-23

https://doi.org/10.1109/HOLM.2018.8611711
Grohmann, Lukas; Bund, Andreas; Lammel, Patricia
Thermosonisches Drahtbonden auf galvanisch abgeschiedenen Oberflächen - Teil 2. - In: Produktion von Leiterplatten und Systemen, ISSN 1436-7505, Bd. 20 (2018), 11, S. 1806-1815

Chernysheva, Daria; Vlaic, Codruta; Leontyev, Igor; Pudova, Lyudmila; Ivanov, Svetlozar; Avramenko, Marina; Allix, Mathieu; Rakhmatullin, Aydar; Maslova, Olga; Bund, Andreas; Smirnova, Nina
Synthesis of Co3O4/CoOOH via electrochemical dispersion using a pulse alternating current method for lithium-ion batteries and supercapacitors. - In: Solid state sciences, ISSN 1293-2558, Bd. 86 (2018), S. 53-59
Im Titel sind "3" und "4" tiefgestellt

https://doi.org/10.1016/j.solidstatesciences.2018.10.005
Wiegmann, Christoph; Wolff, J.; Bund, Andreas
Characterization and influence on the fatigue properties of the metal-turn-over of an electroless nickel coating on an AlCuMgFeNi alloy. - In: Galvanotechnik, ISSN 0016-4232, Bd. 109 (2018), 8, S. 1538-1547

Kaltwasser, Mahsa; Schmidt, Udo; Biswas, Shantonu; Reiprich, Johannes; Schlag, Leslie; Isaac, Nishchay Angel; Stauden, Thomas; Jacobs, Heiko O.
Core-shell transformation-imprinted solder bumps enabling low-temperature fluidic self-assembly and self-alignment of chips and high melting point interconnects. - In: ACS applied materials & interfaces, ISSN 1944-8252, Bd. 10 (2018), 47, S. 40608-40613

https://doi.org/10.1021/acsami.8b12390
Sauerteig, Daniel;
Implementierung und Parametrierung eines physikalischen Simulationsmodells einer Lithium-Ionen Zelle zur Analyse elektrochemisch-mechanischer Wechselwirkungen. - Ilmenau : Universitätsbibliothek, 2018. - 1 Online-Ressource (VI, 117 Seiten, Seite VIII-XXIV)
Technische Universität Ilmenau, Dissertation 2018

Die Interkalationsreaktion von Lithium (Li) in Li-Ionen Batterien ist häufig mit signifikanten Volumenänderungen der Aktivmaterialien verbunden. Zusätzlich kommt es über die Lebensdauer zu einer irreversiblen mechanischen Ausdehnung, die u.a. durch die Reaktion von Elektrolytkomponenten an der Elektrodenoberfläche hervorgerufen wird. Die Limitierung des mechanischen Bauraums in Batteriezellen und -systemen führt in Folge der Elektrodenausdehnung zu mechanische Spannungen, die nachgewiesener Weise die Zellalterung und damit die Eigenschaften des elektrochemischen Systems beeinflussen. Für eine fundamentale Beschreibung des mechanischen Einflusses sind grundlegende elektrochemische Methoden notwendig. Zur physikalischen Beschreibung dieser Effekte stellt diese Arbeit ein umfassendes Simulationsmodell vor. Die elektrochemischen Gleichungen basieren auf dem Modell nach Newman, welches um einen mechanischen und thermischen Ansatz ergänzt wurde. Die mechanische Erweiterung ermöglicht die Berechnung der Volumenänderung der Komponenten in Abhängigkeit der Li-Konzentration und der mechanischen Randbedingungen. Die mechanisch-elektrochemische Kopplung ist dadurch abgebildet, dass die herrschenden mechanischen Drücke die Porosität und somit die ionischen Transporteigenschaften der porösen Elektroden und des Separators beeinflussen. Die temperatur- und konzentrationsabhängige Parametrisierung des elektrochemisch-mechanischen Modells wird vollständig in dieser Arbeit durchgeführt. Die Bestimmung der Eigenschaften der verwendeten Aktivmaterialien erfolgt durch Anwendung spezieller Dreielektroden-Zellen, wodurch Anode und Kathode getrennt voneinander parametrisiert werden. Besonders dünne Elektrodenschichten minimieren dabei den Einfluss des Elektrolyten. Die physikalische Beziehung zwischen dem mechanischen Druck und der ionischen Leitfähigkeit der Komponenten konnte direkt gemessen und mittels Simulationsergebnissen bestätigt werden. Der physikalische Modellansatz verdeutlicht, dass eine mechanische Verspannung von Zellen die Entstehung von Li-Konzentrationsgradienten während der Ladung und Entladung verstärkt.



https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2018000407
Schoetz, Theresa; Kurniawan, Mario; Stich, Michael; Peipmann, Ralf; Efimov, Igor; Ispas, Adriana; Bund, Andreas; Ponce de Leon, Carlos; Ueda, Mikito
Understanding the charge storage mechanism of conductive polymers as hybrid battery-capacitor materials in ionic liquids by in situ atomic force microscopy and electrochemical quartz crystal microbalance studies. - In: Journal of materials chemistry, ISSN 2050-7496, Bd. 6 (2018), 36, S. 17787-17799

https://doi.org/10.1039/C8TA06757K
Bartsch, Heike; Peipmann, Ralf; Klett, Maren; Brauer, Dana; Schober, Andreas; Müller, Jens
PEDOT coated thick film electrodes for in situ detection of cell adhesion in cell cultures. - In: Biosensors, ISSN 2079-6374, Bd. 8 (2018), 4, 105, insges. 13 S.

https://doi.org/10.3390/bios8040105
Grohmann, Lukas; Bund, Andreas; Lammel, Patricia
Thermosonisches Drahtbonden auf galvanisch abgeschiedenen Oberflächen - Teil 1. - In: Produktion von Leiterplatten und Systemen, ISSN 1436-7505, Bd. 20 (2018), 9, S. 1484-1490

Dyck, Tobias; Bund, Andreas
Influence of the bead geometry and the tin layer on the contact resistance of copper conductors. - In: IEEE transactions on components, packaging and manufacturing technology, ISSN 2156-3985, Bd. 8 (2018), 10, S. 1863-1868

https://doi.org/10.1109/TCPMT.2018.2865801
Zech, Claudia; Grätz, Olga; Ivanov, Svetlozar; Grötzsch, Daniel; Hönicke, Philipp; Kayser, Yves; Stamm, Manfred; Beckhoff, Burkhard
In-situ and operando near sulfur K-edge X-ray absorption spectrometry of Li-S battery coin cells. - In: Joint Meeting of the DPG and EPS Condensed Matter Divisions together with the Statistical and Nonlinear Physics Division of the EPS and the Working Groups: Equal Opportunities, Industry and Business, Young DPG, Philosophy of Physics, (all DPG) EPS Young Minds, EPS History of Physics Group, (2018), O 8.2

Hesamedini, Sanez; Ecke, Gernot; Bund, Andreas
Structure and formation of trivalent chromium conversion coatings containing cobalt on zinc plated steel. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 165 (2018), 10, Seite C657-C669

https://doi.org/10.1149/2.0951810jes
Wiegmann, Christoph;
Charakterisierung von NiP-Schichten und alternativen Beschichtungssystemen als Verschleiß- und Korrosionsschutz auf Aluminiumknetlegierungen. - Ilmenau : Universitätsbibliothek, 2018. - 1 Online-Ressource (X, 181 Blätter)
Technische Universität Ilmenau, Dissertation 2018

Verdichterräder in Abgasturboladern werden nach Stand der Technik aus der hochwarmfesten Aluminiumknetlegierung EN AW 2618A hergestellt. Bei Motoren mit Niederdruck-Abgasrückführung müssen diese aus Gründen des Verschleiß- und Korrosionsschutzes zusätzlich beschichtet werden. Die verwendeten Nickel-Phosphor-Schichten haben jedoch einen erheblichen Einfluss auf die dynamische Belastbarkeit. Ziel dieser Dissertation ist es daher, zum einen die Belastungen des Verdichterrades in geeigneten Versuchen nachzustellen und zum anderen eine vergleichbare Datenbasis für verschiedene Verdichterradgrundwerkstoffe und -beschichtungen zu erstellen. Die Belastungen des Verdichterrades werden hierbei in Zugschwellversuchen, verschiedenen Korrosionsversuchen, mittels Kavitation und einer thermischen Alterung nachgestellt. Als untersuchte Grundwerkstoffe werden der aktuell verwendete Werkstoff EN AW 2618A und eine alternative Knetlegierung AA 2055 betrachtet. Als mögliche Beschichtungen werden Nickel-Phosphor-Schichten und plasmachemische Aluminiumoxidschichten untersucht. Im Vergleich der beiden Grundwerkstoffe zeigt sich dabei, dass der alternative Werkstoff in Bezug auf die dynamische Belastbarkeit und die Verschleißbeständigkeit dem aktuell verwendeten Werkstoff deutlich überlegen ist. Die Korrosions- und Alterungsbeständigkeit ist jedoch geringer. Bei den beiden Beschichtungsvarianten zeigen sich die Nickel-Phosphor-Schichten in Bezug auf die Verschleiß- und die Korrosionsbeständigkeit als beste Variante. Die Lebensdauer der Schichten ist jedoch verglichen mit den plasmachemischen Aluminiumoxid-schichten geringer. Durch eine geeignete Anpassung der Nickel-Phosphor-Schichten kann die Lebensdauer jedoch auf ein den plasmachemischen Aluminiumoxidschichten deutlich überlegenes Niveau angehoben werden.



http://nbn-resolving.de/urn:nbn:de:gbv:ilm1-2018000278
Behul, Miroslav; Vojs, Marian; Marton, Marian; Michniak, Pavol; Kurniawan, Mario; Peipmann, Ralf; Vlaic, Codruta Aurelia; Bund, Andreas; Redhammer, Robert
Electrodeposition of cuprous oxide on boron doped diamond electrodes. - In: Advances in electrical and electronic engineering, ISSN 1804-3119, Bd. 16 (2018), 2, S. 239-245

https://doi.org/10.15598/aeee.v16i2.2778
Stich, Michael; Göttlinger, Mara; Kurniawan, Mario; Schmidt, Udo; Bund, Andreas
Hydrolysis of LiPF6 in carbonate-based electrolytes for lithium-ion batteries and in aqueous media. - In: The journal of physical chemistry, ISSN 1932-7455, Bd. 122 (2018), 16, S. 8836-8842
Im Titel ist "6" tiefgestellt

https://doi.org/10.1021/acs.jpcc.8b02080
Leimbach, Martin; Tschaar, Christoph; Schmidt, Udo; Bund, Andreas
Electrochemical characterization of chromium deposition from trivalent solutions for decorative applications by EQCM and near-surface pH measurements. - In: Electrochimica acta, ISSN 1873-3859, Bd. 270 (2018), S. 104-109

https://doi.org/10.1016/j.electacta.2018.03.011
Schoetz, Theresa; Ponce de Leon, Carlos; Bund, Andreas; Ueda, Mikito
Electro-polymerisation of 3,4-ethylenedioxythiophene on reticulated vitreous carbon in imidazolium-based chloroaluminate ionic liquid as energy storage material. - In: Electrochemistry communications, ISSN 1873-1902, Bd. 89 (2018), S. 52-56

https://doi.org/10.1016/j.elecom.2018.02.018
Bund, Andreas; Wiegmann, Christoph; Wolff, J.
Characterization and influence on the fatigue properties of the metal-turn-over of an electroless nickel coating on an AlCuMgFeNi alloy. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, (2018), S. 1-16

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT6082
Schoetz, Theresa; Ponce de Leon, Carlos; Bund, Andreas; Ueda, Mikito
Electro-polymerisation and characterisation of PEDOT in Lewis basic, neutral and acidic EMImCl-AlCl3 ionic liquid. - In: Electrochimica acta, ISSN 1873-3859, Bd. 263 (2018), S. 176-183
Im Titel ist "3" tiefgestellt

https://doi.org/10.1016/j.electacta.2018.01.033
Sauerteig, Daniel; Hanselmann, Nina; Arzberger, Arno; Reinshagen, Holger; Ivanov, Svetlozar; Bund, Andreas
Electrochemical-mechanical coupled modeling and parameterization of swelling and ionic transport in lithium-ion batteries. - In: Journal of power sources, ISSN 1873-2755, Bd. 378 (2018), S. 235-247

https://doi.org/10.1016/j.jpowsour.2017.12.044
Dyck, Tobias; Bund, Andreas
Design of contact systems under consideration of electrical and tribological properties. - In: IEEE transactions on components, packaging and manufacturing technology, ISSN 2156-3985, Bd. 8 (2018), 3, S. 427-438

https://doi.org/10.1109/TCPMT.2017.2788378
Lacitignola, Deborah; Bozzini, Benedetto; Peipmann, Ralf; Sgura, Ivonne
Cross-diffusion effects on a morphochemical model for electrodeposition. - In: Applied mathematical modelling, Bd. 57 (2018), S. 492-513

https://doi.org/10.1016/j.apm.2018.01.005
Hesamedini, Sanaz; Bund, Andreas
Formation of Cr(VI) in cobalt containing Cr(III)-based treatment solution. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 334 (2018), S. 444-449

https://doi.org/10.1016/j.surfcoat.2017.12.006
Vlaic, Codruta Aurelia;
Charakterisierung von galvanischen Multilagen. - In: ZVO-Report, (2017), 5, S. 68

Endrikat, Anna;
Galvanische Komposite aus Kupfer und MAX-Phasen für neuartige Kontaktmaterialien. - In: ZVO-Report, (2017), 4, S. 61

Salloum, Barakat;
Entwicklung von alkalischen Kupferelektrolyten auf Phosphonatbasis. - In: ZVO-Report, (2017), 1, S. 50

Liberale, Francesco; Ispas, Adriana; Bund, Andreas; Magagnin, Luca
Electrochemical aluminum deposition from fluorinated ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2017-01 (2017), 18, 1041

https://doi.org/10.1149/MA2017-01/18/1041
Ivanov, Svetlozar; Mai, Sebastian; Bund, Andreas; Dimitrova, Anna; Krischok, Stefan
(Invited) Redox chemistry of Li-sulfur batteries investigated via electrochemistry, X-ray photoelectron spectroscopy and electron paramagnetic resonance. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2017-02 (2017), 48, 2077

https://doi.org/10.1149/MA2017-02/48/2077
Ispas, Adriana; Endrikat, Anna; Engemann, Thomas; Peipmann, Ralf; Bund, Andreas
(Invited) Pulsed electrodeposition of refractory metals in ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2017-02 (2017), 20, 988

https://doi.org/10.1149/MA2017-02/20/988
Böttcher, René;
Abscheidung von Aluminium und Aluminiumlegierungen aus ionischen Flüssigkeiten. - In: ZVO-Report, (2017), 2, S. 53

Ispas, Adriana; Schlag, Leslie; Böttcher, René; Jacobs, Heiko O.; Bund, Andreas
Electrodeposition of aluminum and aluminum-ruthenium films in ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2017-02 (2017), 19, 971

https://doi.org/10.1149/MA2017-02/19/971
Cuibus, Florina; Ivanov, Svetlozar; Schwalbe, Ulf; Schilling, Marco; Bund, Andreas
State-of-charge and state-of-health estimation of commercial LiFePO4 batteries by means of impedance spectroscopy. - In: Progress reports on impedance spectroscopy, (2017), S. 3-18
Im Titel ist "4" tiefgestellt

https://doi.org/10.1515/9783110449822
Endrikat, Anna; Böttcher, René; Engemann, Thomas; Ispas, Adriana; Peipmann, Ralf; Bund, Andreas
Abscheidung unedler Metalle aus ionischen Flüssigkeiten für den Korrosionsschutz. - In: Galvanotechnik, ISSN 0016-4232, Bd. 108 (2017), 11, S. 2179-2188

Schötz, Theresa; Ponce de Leon, Carlos; Ueda, Mikito; Bund, Andreas
State of the art of rechargeable aluminum batteries in non-aqueous systems. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 164 (2017), 14, Seite A3499-A3502

https://doi.org/10.1149/2.0311714jes
Kaltwasser, Mahsa; Biswas, Shantonu; Stauden, Thomas; Schmidt, Udo; Bund, Andreas; Jacobs, Heiko O.
Bleifreier Lotstapel für fluidische Selbstmontage von Siliziumchips. - In: MikroSystemTechnik Kongress 2017 "MEMS, Mikroelektronik, Systeme", (2017), S. 437-439

Schlag, Leslie; Reiprich, Johannes; Stauden, Thomas; Pezoldt, Jörg; Ispas, Adriana; Bund, Andreas; Schaaf, Peter; Jacobs, Heiko O.
Selbstjustierendes Wachstum von 3D-Nanobrückenverbindungen. - In: MikroSystemTechnik Kongress 2017 "MEMS, Mikroelektronik, Systeme", (2017), S. 317-320

Omelcenko, Alexander; Wulfmeier, Hendrik; Albrecht, Daniel; El Mofid, Wassima; Ivanov, Svetlozar; Bund, Andreas; Fritze, Holger
Thin-film calorimetry: in-situ characterization of materials for lithium-ion batteries. - In: International journal of materials research, ISSN 2195-8556, Bd. 108 (2017), 11, S. 904-919

https://doi.org/10.3139/146.111551
Schötz, Theresa; Ueda, Mikito; Bund, Andreas; Ponce de Leon, Carlos
Preparation and characterization of a rechargeable battery based on poly-(3,4-ethylenedioxythiophene) and aluminum in ionic liquids. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 21 (2017), 11, S. 3237-3246

https://doi.org/10.1007/s10008-017-3658-4
Steinhauer, Miriam; Stich, Michael; Kurniawan, Mario; Seidlhofer, Beatrix-Kamelia; Trapp, Marcus; Bund, Andreas; Wagner, Norbert; Friedrich, K. Andreas
In situ studies of solid electrolyte interphase (SEI) formation on crystalline carbon surfaces by neutron reflectometry and atomic force microscopy. - In: ACS applied materials & interfaces, ISSN 1944-8252, Bd. 9 (2017), 41, S. 35794-35801

https://doi.org/10.1021/acsami.7b09181
Wojciechowski, Jarosław; Kolanowski, &Lstrok;ukasz; Bund, Andreas; Lota, Grzegorz
The influence of current collector corrosion on the performance of electrochemical capacitors. - In: Journal of power sources, ISSN 1873-2755, Bd. 368 (2017), S. 18-29

https://doi.org/10.1016/j.jpowsour.2017.09.069
Khobragade, Shilpa; Swarbrick, Samantha; Gruia, Violeta-Tincuta; Efimov, Igor; Ispas, Adriana; Ostanin, Victor; Bund, Andreas; Ghosh, Sourav
Detection of flexibly bound adsorbate using the nonlinear response of quartz crystal resonator driven at high oscillation amplitude. - In: Electrochimica acta, ISSN 1873-3859, Bd. 252 (2017), S. 424-429

https://doi.org/10.1016/j.electacta.2017.09.027
Fleaca, Claudiu Teodor; Dumitrache, Florian; Sandu, Ion; Dutu, Elena; Ilie, Alina; Banici, Ana-Maria; Vasile, Eugeniu; Vlaic, Codruta; Bund, Andreas; Prodan, Gabriel
Laser pyrolysis synthesis of Sn-Fe-Npolycarbosilazane nanocomposites, characterization and evaluation as energy storage materials. - In: Applied physics. Materials science & processing. - Berlin : Springer, 1973- , ISSN: 1432-0630 , ZDB-ID: 1398311-8, ISSN 1432-0630, Bd. 123 (2017), 11, Article 695, insges. 11 S.

https://doi.org/10.1007/s00339-017-1300-z
Stich, Michael; Pandey, Nisrit; Bund, Andreas
Drying and moisture resorption behaviour of various electrode materials and separators for lithium-ion batteries. - In: Journal of power sources, ISSN 1873-2755, Bd. 364 (2017), S. 84-81

https://doi.org/10.1016/j.jpowsour.2017.08.009
Ispas, Adriana; Wolff, Elisabeth; Bund, Andreas
An electrochemical quartz crystal microbalance study on electrodeposition of aluminum and aluminum-manganese alloys. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 164 (2017), 8, Seite H5263-H5270

https://doi.org/10.1149/2.0381708jes
Weier, Tom; Bund, Andreas; El-Mofid, Wassima; Horstmann, Gerrit Maik; Lalau, Cornel-Constantin; Landgraf, Steffen; Nimtz, Michael; Starace, Marco; Stefani, Frank; Weber, Norbert
Liquid metal batteries - materials selection and fluid dynamics. - In: Final LIMTECH Colloquium and International Symposium on Liquid Metal Technologies, (2017), S. 012013, insges. 14 S.

https://doi.org/10.1088/1757-899X/228/1/012013
Jehl, Pierre; Halbedel, Bernd; Lerp, Marianne; Schmidt, Udo; Teichert, Gerd; Schlütter, Frank
Entrapment of hard particles into Cr(VI)-free conversion layers of electrodeposited zinc coatings to improve corrosion resistance. - In: 21st Symposium on Composites, (2017), S. 434-439

Due to the restriction of passive layers containing Cr6+ [1], which were characterized by excellent corrosion protection due to their self-healing effect for scratches on metal surfaces, current corrosion protection systems consist of chromium (III) -containing thick layer passivation. Due to their lower hardness, current corrosion protection systems are susceptible to mechanical stress. This is particularly critical at barrel plating of screws, rivets etc. where the manufacturing process leads to damages of the corrosion protection layer and consequently to reduced corrosion resistance. To counter this problem, we point out one approach to install hard particles into the passivation layer. The entrapment of the hard particles into the passivation is detected by Glow Discharge Optical Emission Spectrometry. Comparative investigations in the corrosion chamber prove the improvement of the corrosion protection of steel parts with passivation layers containing hard particles.



https://doi.org/10.4028/www.scientific.net/KEM.742.434
Grätz, Olga; Raguzin, Ivan; Zech, Claudia; Ivanov, Svetlozar; Beckhoff, Burkhard; Stamm, Manfred
Analysis and improvement of high energy Li-S battery systems. - In: DPG-Frühjahrstagung (DPG Spring Meeting) of the Condensed Matter Section (SKM), (2017), O 15.1
Abweichende Verfasserangabe: Claudia Zech, Olga Grätz, Ivan Raguzin, Svetlozar Ivanov, Markus Börner, Marco Evertz, Marcelina Pyschik, Daniel Grötzsch, Wolfgang Malzer, Manfred Stamm, Sascha Nowak, and Burkhard Beckhoff

Grieseler, Rolf; Camargo, Magali K.; Hopfeld, Marcus; Schmidt, Udo; Bund, Andreas; Schaaf, Peter
Copper-MAX-phase composite coatings obtained by electro-co-deposition: a promising material for electrical contacts. - In: Surface and coatings technology, ISSN 1879-3347, Bd. 321 (2017), S. 219-228

https://doi.org/10.1016/j.surfcoat.2017.04.060
Dyck, Tobias;
Untersuchung von beschichteten Kontaktgeometrien für Steckverbinder. - In: Galvanotechnik, ISSN 0016-4232, Bd. 108 (2017), 4, S. 660-665

Dyck, Tobias; Bund, Andreas
Auslegung von Kontaktsystemen mit galvanischen Zinnschichten unter Berücksichtigung der elektrischen und tribologischen Eigenschaften. - In: Elektrische und optische Verbindungstechnik 2017, (2017), S. 129-146

Böttcher, René; Spieß, Lothar; Linne, Stefan; Beinersdorf, Heiko
Bestimmung von Presskräften mittels Ultraschall : (Impuls-Echo-Verfahren). - In: ZfP-Zeitung, ISSN 1616-069X, Bd. 153 (2017), S. 33-35

Gligor, Delia; Cuibus, Florina; Peipmann, Ralf; Bund, Andreas
Novel amperometric sensors for nitrite detection using electrodes modified with PEDOT prepared in ionic liquids. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 21 (2017), 1, S. 281-290

http://dx.doi.org/10.1007/s10008-016-3368-3
Sauerteig, Daniel; Ivanov, Svetlozar; Reinshagen, Holger; Bund, Andreas
Reversible and irreversible dilation of lithium-ion battery electrodes investigated by in-situ dilatometry. - In: Journal of power sources, ISSN 1873-2755, Bd. 342 (2017), S. 939-946

http://dx.doi.org/10.1016/j.jpowsour.2016.12.121
Fritz, Mathias;
Galvanische Metallisierung von Strahlungsdetektoren. - In: ZVO-Report, (2016), 4, S. 61

Stich, Michael;
Zur Rolle von Wasserspuren in Lithium-Ionen-Batterien. - In: ZVO-Report, (2016), 3, S. 61

Wiegmann, Christoph;
Verschleiß- und Korrosionsschutzschichten für abgasführende Aluminiumknetlegierungen. - In: ZVO-Report, (2016), 1, S. 30

Leimbach, Martin;
Charakterisierung von Abscheideprozessen mit der elektrochemischen Quarzmikrowaage. - In: ZVO-Report, (2016), 5, S. 55

Peipmann, Ralf; Endrikat, Anna; Bund, Andreas
Preparation of Pt@Cu core-shell particles incorporated in poly-(3,4-ethylenedioxythiophene) for catalytic applications. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-02 (2016), 46, 3386

https://doi.org/10.1149/MA2016-02/46/3386
Camargo, Magali K.; Schmidt, Udo; Bund, Andreas
Electrochemical codeposition of TiO2 nanoparticles with zinc. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-02 (2016), 54, 4125
Im Titel ist "2" tiefgestellt

https://doi.org/10.1149/MA2016-02/54/4125
Fritz, Mathias; Nieland, Sabine; Wittig, Tobias; Bund, Andreas
Novell plating processes for silicon based pixel detectors. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-02 (2016), 32, 2078

https://doi.org/10.1149/MA2016-02/32/2078
Grieseler, Rolf; Camargo, Magali K.; Hopfeld, Marcus; Diaz Tang, Isabel; Bund, Andreas; Schaaf, Peter
MAX phase thin films as electrical-conductive corrosion-protective coatings with self-healing abilities. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-02 (2016), 14, 1369

https://doi.org/10.1149/MA2016-02/14/1369
Ivanov, Svetlozar; Mai, Sebastian; Müller, Andre; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas
Understanding the effects of diphenyl octyl phosphate as a solid electrolyte interphase forming additive for Li-ion batteries. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-03 (2016), 2, 1078

https://doi.org/10.1149/MA2016-03/2/1078
Stich, Michael; Ivanov, Svetlozar; Bund, Andreas
Hygroscopic and drying behaviour of electrodes and separators for lithium ion batteries. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2016-03 (2016), 2, 598

https://doi.org/10.1149/MA2016-03/2/598
Stadie, Philipp; Bartsch, Heike; Peipmann, Ralf; Ispas, Adriana; Bača, Martin; Müller, Jens; Bund, Andreas; Schober, Andreas; Witte, Hartmut
Surface refinement of thick film gold electrodes for 3D MEAs using electro polymerization of PEDOT. - Reutlingen. - 1 Online-Ressource (1 Seiten)Publikation entstand im Rahmen der Veranstaltung: MEA Meeting 2016, 10th International Meeting on Substrate-Integrated Electrode Arrays, Reutlingen, Germany, 28 Jun - 1 Jul, 2016. - (Frontiers in Neuroscience Conference Abstract)

http://dx.doi.org/10.3389/conf.fnins.2016.93.00094
Kutzschbach, Peter; Bund, Andreas; Jacob, Saša Peter
Feierlichkeiten zur Stiftungsprofessur in Ilmenau - Übergang in reguläre Haushaltsfinanzierung erfolgreich vollzogen. - In: WOMag, ISSN 2195-5891, Bd. 5 (2016), 4, S. 34-35

Martens, Sladjana; Ispas, Adriana; Asen, Ludwig; Seidl, Lukas; Stimming, Ulrich; Schneider, Oliver; Bund, Andreas
Influence of fluid dynamics on the electrochemical deposition of tantalum. - In: ECS transactions, ISSN 1938-6737, Bd. 75 (2016), 15, S. 287-295

https://doi.org/10.1149/07515.0287ecst
Ispas, Adriana; Vlaic, Codruta Aurelia; Camargo, Magali K.; Bund, Andreas
Electrochemical deposition of aluminum and aluminum-manganese alloys in ionic liquids. - In: ECS transactions, ISSN 1938-6737, Bd. 75 (2016), 15, S. 657-665

https://doi.org/10.1149/07515.0657ecst
Gruia, Violeta-Tincuta; Efimov, Igor; Ispas, Adriana; Bund, Andreas
Electrochemical detection of neurotransmitters using modified PEDOT electrodes. - In: ECS transactions, ISSN 1938-6737, Bd. 75 (2016), 16, S. 149-155

https://doi.org/10.1149/07516.0149ecst
Leimbach, Martin; Schmidt, Udo; Bund, Andreas
Herstellung und Charakterisierung galvanisch erzeugter Zinn-Nickel/TiO2-Dispersionsschichten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 107 (2016), 9, S. 1818-1824
Im Titel ist "2" tiefgestellt

Dimitrova, Anna; Walle, Marit; Himmerlich, Marcel; Krischok, Stefan; Ispas, Adriana; Bund, Andreas
Two air- and water- stable ionic liquids in the presence of TaF5 and NbF5 : photoelectron spectroscopy study. - In: 80th Annual Meeting of the DPG and DPG-Frühjahrstagung (Spring Meeting) of the Condensed Matter Section (SKM), (2016), O 16.12, insges. 1 S.

Kuriganova, Alexandra B.; Leontyeva, Daria V.; Ivanov, Svetlozar; Bund, Andreas; Smirnova, Nina V.
Electrochemical dispersion technique for preparation of hybrid MOx-C supports and Pt/MOx-C electrocatalysts for low-temperature fuel cells. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 46 (2016), 12, S. 1245-1260
Im Titel ist "x" tiefgestellt

http://dx.doi.org/10.1007/s10800-016-1006-5
El Mofid, Wassima;
Synthesis and characterization of novel cathode material with improved specific capacity and safety for lithium ion batteries. - Ilmenau : Universitätsbibliothek, 2016. - 1 Online-Ressource (xix, 121 Seiten)
Technische Universität Ilmenau, Dissertation 2016

Die steigenden Anforderungen an Lithium-Ionen-Batterien mit hoher spezifischer Leistung und Energie haben zur Entwicklung von mehreren Klassen von Materialien für die positive Elektrode geführt. Darunter sind unter anderem die vielversprechenden LiNixMnyCo1-x-yO2 (NMC) Materialien. In diesem Zusammenhang ist das Thema dieser Arbeit eine umfangreichen Studie der elektrochemischen und strukturellen Eigenschaften des ursprünglichen Materials NMC (3:1:1) (LiNi0.6Mn0.2Co0.2O2) und der drei neuen Materialien, die entweder durch Mono-Substitution von Co mit Al oder Fe: NMCA (LiNi0.6Mn0.2Co0.15Al0.05O2) und NMCF (LiNi0.6Mn0.2Co0.15Fe0.05O2) oder durch doppelte Substitution von Co mit Al und Fe NMCAF (LiNi0.6Mn0.2Co0.15Al0.025 Fe0.025O2) hergestellt wurden. Im ersten Schritt wurde eine Optimierung der Synthesebedingungen durchgeführt. Dazu wurden verschiedene Verfahren (z.B. Röntgenbeugung, Rasterelektronenmikroskopie) verwendet, um homogene Phasen mit gut geordneter Struktur zu erhalten. Im zweiten Schritt wurden Struktur, morphologische und elektrochemische Eigenschaften der vier Materialien untersucht. Eine detailliertere Untersuchung wurde NMCAF gewidmet. Dieses Material zeigte die besten elektrochemischen Eigenschaften im Vergleich zu den ursprünglichen und den mono-substituierten Materialien. Ziel ist es zu verstehen, was die Mechanismen hinter der Verbesserung des elektrochemischen Verhaltens des doppelsubstituierten Materials sind. Schließlich wurde der Sicherheitsaspekt von NMCAF auf Basis einer detaillierten Untersuchung der thermischen Stabilität während der Lithium-Ionen-Deinterkalation diskutiert.



http://nbn-resolving.de/urn:nbn:de:gbv:ilm1-2016000524
Wojciechowski, Jarosław; Szubert, Karol; Peipmann, Ralf; Fritz, Mathias; Schmidt, Udo; Bund, Andreas; Lota, Grzegorz
Anti-corrosive properties of silane coatings deposited on anodised aluminium. - In: Electrochimica acta, ISSN 1873-3859, Bd. 220 (2016), S. 1-10

http://dx.doi.org/10.1016/j.electacta.2016.10.080
Dyck, Tobias; Ober-Wörder, Philipp; Bund, Andreas
Calculation of the wear surface and the coefficient of friction for various coated contact geometries. - In: Wear, ISSN 0043-1648, Bd. 368/369 (2016), S. 390-399

http://dx.doi.org/10.1016/j.wear.2016.10.014
Vrublevsky, Igor; Ispas, Adriana; Chernyakova, Katsiaryna; Bund, Andreas
Effect of continuous magnetic field on the growth mechanism of nanoporous anodic alumina films on different substrates. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 20 (2016), 10, S. 2765-2772

http://dx.doi.org/10.1007/s10008-016-3274-8
Dyck, Tobias; Bund, Andreas
A wear model for tin surfaced contact geometries. - In: 28th International Conference on Electric Contacts, ISBN 978-0-9954659-0-9, (2016), S. 421-426

Lalau, Cornel-Constantin; Dimitrova, Anna; Himmerlich, Marcel; Ispas, Adriana; Weier, Tom; Krischok, Stefan; Bund, Andreas
An electrochemical and photoelectron spectroscopy study of a low temperature liquid metal battery based on an ionic liquid electrolyte. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 163 (2016), 10, Seite A2488-A2493

http://dx.doi.org/10.1149/2.0051613jes
Kiefer, Ronny;
Korrosionsschadensfälle verchromter galvanischer Überzüge : Erklären der Korrosionsmechanismen mittels Elektrochemie und praktische Absicherung der Ergebnisse an Fahrzeugen. - Ilmenau : Universitätsbibliothek, 2016. - 1 Online-Ressource (127 Seiten)
Technische Universität Ilmenau, Dissertation 2016

Mit dem Wechsel der Zusammensetzung von Streusalzmischungen zum Enteisen von Straßen in der Winterperiode oder zum Befeuchten von unbefestigten staubigen Straßen können sich Korrosionsschäden an verchromten Exterieurbauteilen der Automobilindustrie einstellen. Der bisher unbekannte Schadensmechanismus der Chromkorrosion wurde in der vorliegenden Arbeit untersucht und erklärt. Mittels Elektrochemie wurde das Korrosionsverhalten der einzelnen Metallüberzüge von dekorativ verchromten Bauteiloberflächen in Natrium-, Magnesium- und Calciumchloridlösungen verschiedener Molarität beschrieben und nachvollzogen. Diese Arbeit hat grundlegend das Verhalten der in der Praxis verwendeten Salze unter Berücksichtigung der realen Bedingungen seitens Klima, Salzmischung und Beaufschlagung in Kombination mit weiteren Einflüssen wie Verschmutzung etc. betrachtet, qualitativ und quantitativ erfasst und analysiert. Es konnten kritische Parameter für das Korrosionssystem Cr / Ni identifiziert werden, die zu einer Deckschichtbildung auf Nickelüberzügen führt. Dieses Phänomen wurde mittels elektrochemischer Methoden reproduziert und analysiert, sodass auch unter Feldbedingungen der Korrosionsschaden reproduzierbar dargestellt werden kann. Der wesentliche Einfluss des Mediums auf das Korrosionsverhalten konnte ermittelt und als eine Ursache zusammen mit der vorherrschenden Luftfeuchte für das Auftreten des Schadens identifiziert werden. In Natriumchloridlösungen löst sich stets Glanznickel als galvanische Anode auf und Chrom passiv bleibt (Kathode). Mit Erhöhung der Konzentrationen von CaCl2 bzw. MgCl2 löst sich der Chromüberzug auf, da Glanznickel elektrochemisch passiv wird. Durch Auslagerungsversuche von Chrom in gesättigter CaCl2 Lösung konnte Chromatbildung bestätigt werden. Zudem wurde verdeutlicht, dass die Chromauflösung in hochmolaren CaCl2 bzw. MgCl2 Elektrolyten abhängig von der Oberflächenstruktur (mikrorissig oder mikroporig) und dem damit verbundenen lokalen Auflösungsstrom ist. Das Flächenverhältnis zwischen Glanznickel und Chrom ist der entscheidende Faktor. Die galvanostatischen Halteversuche lassen vermuten, dass bei einem durchgängigen, feinmaschigen Rissnetzwerk die Anodenfläche wesentlich größer als bei vorhandenen Mikroporen ist. Dadurch wird bei einem Riss die lokal wirkende Stromdichte reduziert. Die Korrosionsreaktionen werden besser auf der nach oben hin offenen Nickelfläche verteilt. Weiterhin bildet die geometrische Rissstruktur der Oberfläche unter praktischen Korrosionsbedingungen eine Ausbreitungsbarriere, falls es doch zu Chromkorrosion kommen sollte. In den Praxisuntersuchungen wurde zudem festgestellt, dass eine große Glanznickelanodenfläche eines Rissnetzwerkes gegen Chromkorrosion hilft, aber bei Anwesenheit von dauerfeuchten niedrig molaren Salzen mit CaCl2 bzw. MgCl2 einen großen Nachteil hat. Korrosionsvorgänge schreiten ständig im Glanznickel voran und verkürzen die Lebenszeit der Überzüge signifikant. Unter diesen Bedingungen ist eine mikroporöse Oberflächenstruktur vorteilhaft, weil weniger Anodenfläche nach oben hin offen ist. Die Erkenntnis daraus ist, dass die Ursachen seitens Medium und relativer Luftfeuchte nicht vermeidbar, sondern klimatisch und länderspezifisch sind. Weiterhin konnte in Natriumchloridlösungen das Korrosionsverhalten des bestehenden Systems entsprechend der Auslegung aus den 60ern Jahren nachvollzogen werden. Unter Belastung des Korrosionssystems mit NaCl sind keine Schäden zu verzeichnen. Das Phänomen der Nickelpassivierung konnte nur in bestimmten Medien (CaCl2 und MgCl2) nachgewiesen werden. Die Parameter für elektrochemische Kennwerte, Temperatur, Luftfeuchte und Konzentration des Mediums konnten in aktuellen Laborprüfungen einfließen und diese signifikant verkürzen. Als Quintessenz konnte herausgearbeitet werden, dass sich weder aktuell verfügbare mikroporige- noch mikrorissige Verchromungen als weltweit einsetzbar eignen. Beide Oberflächenarten haben je nach lokal vorherrschenden Medien und Klimawerten Schwächen und Stärken. Die Schwächen können zum Bauteilversagen mit anschließenden Kundenreklamationen führen. Durch Legieren von Nickel mit Phosphor, Wolfram oder Zinn können Korrosionseigenschaften signifikant verändert werden. Elektrochemische Untersuchungen geben einen Ausblick darüber, wie eine Anpassung von Glanznickel an weltweite Bedingungen erfolgen kann. Einige Varianten wurden von Enthone im Technikum galvanisch abgeschieden und in das vorhandene Korrosionssystem Ni / Cr eingebaut. Erste Tests sahen vielversprechend aus. Laborprüfungen und Feldtests müssen zeigen, ob die modifizierte Galvanische Anode sowohl unter NaCl Belastung als auch unter CaCl2 bzw. MgCl2 Belastung in der Praxis funktioniert.



http://nbn-resolving.de/urn:nbn:de:gbv:ilm1-2016000397
Ivanov, Svetlozar; Barylyak, Adriana; Besaha, Khrystyna; Dimitrova, Anna; Krischok, Stefan; Bund, Andreas; Bobitski, Jaroslav
Enhanced lithium ion storage in TiO2 nanoparticles, induced by sulphur and carbon co-doping. - In: Journal of power sources, ISSN 1873-2755, Bd. 326 (2016), S. 270-278
Im Titel ist "2" tiefgestellt

http://dx.doi.org/10.1016/j.jpowsour.2016.06.116
Sandjaja, Marco; Stolle, Thomas; Bund, Andreas; Lang, Klaus-Dieter
Investigation of all wet chemical process for the barrier formation in high aspect ratio silicon vias. - In: IEEE transactions on electron devices, ISSN 1557-9646, Bd. 63 (2016), 8, S. 3199-3204

https://doi.org/10.1109/TED.2016.2581312
Gruia, Violeta-Tincuta;
Preparation and electrochemical performance of PEDOT - AuNPs nanocomposite layers for the seletive detection of neurotransmitters. - Ilmenau : Universitätsbibliothek, 2016. - 1 Online-Ressource (119 Seiten)
Technische Universität Ilmenau, Dissertation 2016

Poly-3,4-ethylendioxythiophen (PEDOT) ist, aufgrund seiner guten elektrochemischen Stabilität und hoher Leitfähigkeit eines der am meistgenutzten leitfähigen Polymere [1]. Es wurde im Jahr 1988 von der Bayer AG, Leverkusen synthetisiert [1]. Jüngst wurde der Erforschung von Verbundmaterialien besondere Aufmerksamkeit zuteil, deren Grundlage leitfähiger Polymere bilden, auf die verschiedene Metalle abgeschieden wurden. Diese Nanoverbundmaterialien haben ein geringes Gewicht, eine große Oberfläche, das Potenzial zur nicht-enzymatischen Detektion und sind preisgünstig. Die Verarbeitung ist unkompliziert und einfach ausbaubar [1]. Catecholamine sind eine Stoffgruppe von Neurotransmittern und ihre Detektion im menschlichen Körper ist für Neurowissenschaftler von großem Interesse. Zu der Stoffgruppe zählen Dopamin, Serotonin, Adrenalin und sie spielen wichtige Rollen in verschiedenen biologischen, pharmakologischen und physikalischen Prozessen. Unter den verschiedenen Analysetechniken haben insbesondere elektrochemische Methoden viel Beachtung erfahren, da sie einfach, selektiv, günstig und weniger zeitaufwändig sind. Zudem können sie in einer Echtzeit-in-situ Bestimmung angewandt werden [2]. Die elektrochemische Analyse auf unmodifizierten Elektroden wie glasartigem Kohlenstoff oder Goldelektroden, wie in unserer Arbeit verwendet, hat ihre Limitierungen aufgrund von überlappenden voltammetrischen Peaks und hohen Konzentrationen von Ascorbinsäure [3]. Das Hauptziel dieser Arbeit war es eine neue Generation von modifizierten Elektroden, PEDOT/Au Nanopartikel, zu entwickeln, die differenzierbare Oxidationspeaks des Analyten aufweisen. Die Sensitivität der Dopamindetektion steigerte sich mit PEDOT/Au Nanopartikeln um das Dreifache, von 0,13+/-0,01/ microA/microM auf 0,3+/-0,03/ microA/microM. Die zweite lineare Region die im nanomolekularen Bereich gefunden wurde weist eine höhere Steigung auf (0,04+/-0,0002/ microA/microM). Dies entspricht einer höheren Sensitivität. Auch für die Serotonindetektion wurde mit PEDOT/Au Nanopartikeln eine höhere Sensitivität erreicht (0,4+/-0,04/ microA/microM). Der Vergleich mit den Daten der PEDOT-Schicht (0,13+/-0,004/ microA/microM) zeigt auch hier eine um das Dreifache gesteigerte Sensitivität. Eine zweite höher sensitive lineare Region wurde für eine Konzentration im nanomolekularen Bereich zwischen 50 nM und 500 nM nur für die Nanokompositschichten gefunden. Die Sensitivität für die Serotonindetektion von Nanokompositelektroden stieg im nanomolaren Bereich um das Hundertfache an. Um die abgeschiedene Metalmasse auf den vorsynthetisierten Polymerfilmen zu berechnen, haben wir ein Model vorgeschlagen, dass auf den EQCM Untersuchungen beruht. Die Reproduzierbarkeit wurde ebenfalls untersucht und diese Daten beweisen auch, dass PEDOT Nanokompositschichten einen vielversprechender Kandidaten für einen amperometrischen Sensor für die elektrochemische Detektion von Catecholaminen darstellt.



http://nbn-resolving.de/urn:nbn:de:gbv:ilm1-2016000304
Wulfmeier, Hendrik; Omelcenko, Alexander; Albrecht, Daniel; Klimm, Detlef; El Mofid, Wassima; Strafela, Marc; Ulrich, Sven; Bund, Andreas; Fritze, Holger
Thermal stability of materials for thin-film electrochemical cells investigated by thin-film calorimetry. - In: MRS advances, ISSN 2059-8521, Bd. 1 (2016), 15, S. 1043-1049

http://dx.doi.org/10.1557/adv.2016.72
Dyck, Tobias; Bund, Andreas
An adaption of the Archard equation for electrical contacts with thin coatings. - In: Tribology international, ISSN 1879-2464, Bd. 102 (2016), S. 1-9

http://dx.doi.org/10.1016/j.triboint.2016.05.005
Kuriganova, Alexandra B.; Vlaic, Codruta A.; Ivanov, Svetlozar; Leontyeva, Daria V.; Bund, Andreas; Smirnova, Nina V.
Electrochemical dispersion method for the synthesis of SnO2 as anode material for lithium ion batteries. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 46 (2016), 5, S. 527-538
Im Titel ist "2" tiefgestellt

http://dx.doi.org/10.1007/s10800-016-0936-2
Camargo, Magali K.; Tudela, Ignacio; Schmidt, Udo; Cobley, Andrew J.; Bund, Andreas
Ultrasound assisted electrodeposition of Zn and Zn-TiO2 coatings. - In: Electrochimica acta, ISSN 1873-3859, Bd. 198 (2016), S. 287-295
Im Titel ist "2" tiefgestellt

http://dx.doi.org/10.1016/j.electacta.2016.03.078
Ivanov, Svetlozar; Barylyak, Adriana; Besaha, K.; Bund, Andreas; Bobitski, Yaroslav; Wojnarowska-Nowak, R.; Yaremchuk, Iryna; Kus-Liâskiewicz, Małgorzata
Synthesis, characterization, and photocatalytic properties of sulfur- and carbon-codoped TiO2 nanoparticles. - In: Nanoscale research letters, ISSN 1556-276X, Bd. 11.2016, 1, Article 140, insges. 12 S.
Im Titel ist "2" tiefgestellt

http://dx.doi.org/10.1186/s11671-016-1353-5
Lyutov, Vladimir; Gruia, Violeta; Efimov, Igor; Bund, Andreas; Tsakova, Vessela
An acoustic impedance study of PEDOT layers obtained in aqueous solution. - In: Electrochimica acta, ISSN 1873-3859, Bd. 190 (2016), S. 285-293

http://dx.doi.org/10.1016/j.electacta.2015.12.177
Hesamedini, Sanaz;
Wirkungsmechanismus von Kobalt in Cr(III)-Passivierungen. - In: ZVO-Report, (2015), 4, S. 51

El Mofid, Wassima; Ivanov, Svetlozar; Bund, Andreas; Rentenberger, Stephan; Goers, Dietrich
Inhibition of Al/Cu contact corrosion in lithium ion batteries. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2015-01 (2015), 2, 285

https://doi.org/10.1149/MA2015-01/2/285
Ispas, Adriana; Bund, Andreas
On the mechanism of electrochemical reduction of niobium halides in ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2015-02 (2015), 44, 1757

https://doi.org/10.1149/MA2015-02/44/1757
Bund, Andreas; Ispas, Adriana; Vlaic, Codruta Aurelia; Foerg, Andrea; Masset, Patrick J.
Corrosion protection of low carbon steels by electrodeposited aluminum alloys. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2015-02 (2015), 12, 646

https://doi.org/10.1149/MA2015-02/12/646
Dimitrova, Anna; Himmerlich, Marcel; Eisenhardt, Anja; Krischok, Stefan; Müller, Andre; Stich, Michael; Ivanov, Svetlozar; Bund, Andreas
Improved electrolyte-additive induced performance of graphite anodes for Lithium-ion batteries - electrochemical and electrode surface studies. - In: Tagungsband, (2015), S. 425-433

Sandjaja, Marco;
Nasschemisches Verfahren zur Abscheidung von Diffusionsbarrieren für Kupfer in VIAs mit hohem Aspektverhältnis. - Berlin, 2015. - v, 117 Seiten
Technische Universität Ilmenau, Dissertation 2016

Tag der Verteidigung: 21.03.2016

Die Herstellung einer Diffusionssperre zur Vermeidung von Migrationsvorgängen an Schichtgrenzen hat heutzutage für den Aufbau von 3D-Strukturen beim Wafer-Level-Packaging immer mehr Bedeutung gewonnen. Herkömmliche Barriereschichten für Si-Wafer, wie SiO 2, Si 2N 4, werden üblicherweise durch Gasphasenreaktionen erzeugt. Sie genügen aber nicht mehr den heutigen Anforderungen. Nasschemisches Abscheideverfahren und neue Materialien haben in den letzten Jahren aufgrund der guten Kosteneffizienz und der vergleichbar guten Abscheidungsqualität ein besonderes Interesse der Industrie geweckt. Bei der Suche nach einem geeigneten Barrierematerial, das sich außenstromlos abscheiden lässt, werden amorphen Materialien aus Refraktär- und Nichtmetallelementen vorgeschlagen. Insbesondere solche Materialien; die auf einer CoP basieren, gelten als aussichtsreiche Kandidaten zur Unterbindung von Cu-Diffusion. Das zweithöchstschmelzende Element, das Re, lässt sich außenstromlos mit vergleichbar hohem Anteil im Volumen der amorphen CoReP-Schicht abscheiden. Durch solche Re-Konzentration besitzt CoReP eine hohe thermische Stabilität und gilt daher als ein vielversprechender Kandidat für Barrierematerialien. Der stromlose CoReP-Abscheidungsprozess besteht in der Regel aus mehreren Behandlungsschritten, wie Hydrophilierung, Silanisierung, Aktivierung und Metallisierung. In der vorliegenden Arbeit werden die Schritte mit den herkömmlichen Charackterisierungsmethoden für die Si-Waferoberfläche untersucht. Die Untersuchungsergebnisse liefern Erkenntnisse über die Zusammenhänge der einzelnen Parameter und die Möglichkeit zur Optimierung des Abscheidungsverfahrens. Darüber hinaus besteht Bedarf an einer Methode zur Untersuchung der Oberflächenchemie in VIAs. Eine auf Photovolumineszenz basierte Charackterisierungsmethode zur bildlichen Veranschaulichung der anwesenden funktionellen Gruppen im VIA sowie zur Untersuchung der Beleuchtungsdichte der Haftschichtvermittler wird deswegen entwickelt. Außerdem wird die Badformulierung bei den einzelnen Prozessschritten an das Ziel der Arbeit angepasst. Zur Verbesserung des Stofftransports wird bei der CoReP-Abscheidung eine Stoßmethode eingesetzt. Dadurch erfolgt die CoReP-Abscheidung bis in die Tiefe der VIAs. Die Arbeiten führen zu einer neuartigen Arbeitstechnik zur nasschemischen Abscheidung einer CoReP-Legierung mit hohem Aspektverhältnis.



Vlaic, Codru¸ta Aurelia; Dorneanu, Sorin-Aurel
Galvanostatic graphite electroactivation for hydrogen peroxide electrosynthesis by multi-sequence and auto-adaptive techniques. - In: Studia Universitatis Babe¸s-Bolyai. Chemia / Universitatea Babe¸s-Bolyai. - Cluj-Napoca : Univ., 1962- , ISSN: 0039-3401 , ZDB-ID: 241865-4, ISSN 0039-3401, Bd. 60 (2015), 3, S. 141-150

Dimitrova, Anna; Müller, Andre; Ivanov, Svetlozar; Himmerlich, Marcel; Eisenhardt, Anja; Bund, Andreas; Krischok, Stefan
Improved electrolyte-additive induced performance of graphite anodes for lithium-ion batteries - electrochemical and electrode surface studies. - In: 79th Annual Meeting of the DPG and DPG-Frühjahrstagung (Spring Meeting) of the Condensed Matter Section (SKM) together with the Divisions: History of Physics, Gravitation and Relativity, Microprobes, Theoretical and Mathematical Physics, and Working Groups: Energy, Equal Opportunities, Information, Philosophy of Physics, Physics and Disarmament, young DPG ; March, 15 - 20, 2015, Technische Universität Berlin, 2015, CPP 37.12

Efimov, Igor; Gruia, Violeta-Tincuta; Rumiche, Francisco; Bund, Andreas; Ispas, Adriana
An electrochemical quartz crystal microbalance study on adsorption of single walled carbon nanotubes onto poly[3,4-ethylenedioxythiophene] layers. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 19 (2015), 9, S. 2581-2589

https://doi.org/10.1007/s10008-015-2979-4
Wulfmeier, Hendrik; Albrecht, Daniel; Fischer, Julian; Ivanov, Svetlozar; Bund, Andreas; Ulrich, Sven; Fritze, Holger
Thin-film calorimetry: analytical tool for in-situ characterization of lithium ion batteries. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 162 (2015), 4, Seite A727-A736

http://dx.doi.org/10.1149/2.0741504jes
Lalau, Cornel-Constantin; Bund, Andreas; Ispas, Adriana; Weier, Tom
Sodium-bismuth-lead low temperature liquid metal battery. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, (2015), S. 1-6

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT4808
Vlaic, Codruta Aurelia; Ivanov, Svetlozar; Peipmann, Ralf; Eisenhardt, Anja; Himmerlich, Marcel; Krischok, Stefan; Bund, Andreas
Electrochemical lithiation of thin silicon based layers potentiostatically deposited from ionic liquid. - In: Electrochimica acta, ISSN 1873-3859, Bd. 168 (2015), S. 403-413

http://dx.doi.org/10.1016/j.electacta.2015.03.216
Tarish, Samar; Wang, Zhijie; Al-Haddad, Ahmed; Wang, Chengliang; Ispas, Adriana; Romanus, Henry; Schaaf, Peter; Lei, Yong
Synchronous formation of ZnO/ZnS core/shell nanotube arrays with removal of template for meliorating photoelectronic performance. - In: The journal of physical chemistry, ISSN 1932-7455, Bd. 119 (2015), 3, S. 1575-1582
Correction. - Bd. 119 (2015), 25, S. 14461

http://dx.doi.org/10.1021/jp510835n
Ispas, Adriana;
Neue Materialbeschichtungen für die Luft- und Raumfahrt. - In: ZVO-Report, (2014), 2, S. 46

Lalau, Cornel-Constantin;
Flüssigmetallbatterien - stationäre Energiespeicher der Zukunft. - In: ZVO-Report, (2014), 4, S. 52

Camargo, Magali K.; Tudela, Ignacio; Schmidt, Udo; Cobley, Andrew J.; Bund, Andreas
Ultrasound assisted electrodeposition of Zn-TiO2 dispersion coatings. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-02 (2014), 23, 1356

https://doi.org/10.1149/MA2014-02/23/1356
Grieseler, Rolf; Camargo, Magali K.; Hopfeld, Marcus; Bund, Andreas; Schaaf, Peter
Copper-nanolaminate composites - a new and promising material for electrical contacts in high voltage and high current applications. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-02 (2014), 15, 812

https://doi.org/10.1149/MA2014-02/15/812
Bund, Andreas; Ispas, Adriana; Mutschke, Gerd
Magnetohydrodynamic effects in electrodeposition reactions. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-02 (2014), 17, 922

https://doi.org/10.1149/MA2014-02/17/922
Ivanov, Svetlozar; Grieseler, Rolf; Cheng, Lin; Schaaf, Peter; Bund, Andreas
Electrochemical performance of Si modified TiO2 nanotube arrays investigated in Li-ion containing ionic liquid electrolyte. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-02 (2014), 5, 360
Im Titel ist "2" tiefgestellt

https://doi.org/10.1149/MA2014-02/5/360
Wulfmeier, Hendrik; Albrecht, Daniel; Fischer, Julian; Ivanov, Svetlozar; Bund, Andreas; Ulrich, Sven; Fritze, Holger
Thin-film calorimetry - novel analytical tool for in situ characterization of lithium-ion batteries. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-04 (2014), 4, 740

https://doi.org/10.1149/MA2014-04/4/740
Poudyal, Aditya; Denisov, Evgeny; Bund, Andreas
Study of transient behavior of vanadium redox flow battery at varying flow rates and states of charge. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2014-01 (2014), 4, 388

https://doi.org/10.1149/MA2014-01/4/388
Cuibus, Florina; Bund, Andreas
Trend und Status der Technologien zum Batterierecycling - ein Überblick :
Trends and status on the current battery recycling technologies - an overview. - In: WOMag, ISSN 2195-5891, Bd. 3 (2014), 11, S. 10-11

Gligor, Delia; Cuibus, Florina
Leitfähige Polymere als vielversprechender Kandidat für hochempfindliche amperometrische Sensoren :
Conducting polymers, a promising candidate for highly sensitive amperometric sensors. - In: WOMag, ISSN 2195-5891, Bd. 3 (2014), 11, S. 4-5

Camargo, Magali K.; Schmidt, Udo; Bund, Andreas
Galvanische Abscheidung von Zink-TiO2-Dispersionsschichten: Einfluss von anionischen und kationischen Zusätzen auf den Partikeleinbau :
Electrodeposition of Zn-TiO2 dispersion coatings: the effect of anionic and cationic surfactantson particle incorporation. - In: WOMag, ISSN 2195-5891, Bd. 3 (2014), 1, S. 20-21
Im Titel ist "2" tiefgestellt

Szalai, Thomas; Schwalbe, Ulf; Schilling, Marco; Endert, Fabian; Heidrich, Tobias; Ivanov, Svetlozar
Design of an active battery management system for electric vehicles. - In: PCIM Europe 2014, (2014), S. 370-377

http://ieeexplore.ieee.org/document/6841260/
Ispas, Adriana; Bund, Andreas
Electrodeposition in ionic liquids. - In: The Electrochemical Society interface, ISSN 1944-8783, Bd. 23 (2014), 1, S. 47-51

https://doi.org/10.1149/2.F05141if
Bund, Andreas; Endres, Frank
Interfacial electrochemistry of ionic liquids. - In: The Electrochemical Society interface, ISSN 1944-8783, Bd. 23 (2014), 1, S. 45

https://doi.org/10.1149/2.F04141if
Teichert, Gerd; Abawi, Sabine; Camargo, Magali K.; Halbedel, Bernd; Lerp, Marianne; Schmidt, Udo; Wilke, Marcus; Spieß, Lothar
Zerstörungsfreie Charakterisierung mechanischer Eigenschaften von hartstoffpartikelhaltigen Passivierungsschichten auf galvanischen Zink- und Zinklegierungsschichten. - In: The e-journal of nondestructive testing & ultrasonics, Bd. 19 (2014), 3, DGZfP 2013, Session: Korrosion, Mi.3.B.2, insges. 8 S.

http://nbn-resolving.de/urn:nbn:de:gbv:ilm1-2016102106
Hahn, Sebastian;
Grundlagenuntersuchungen zur Wirkweise und Kontrolle von Katalysatoren in autokatalytischen Bädern zur Metallabscheidung, 2014. - Online-Ressource (PDF-Datei: 149 Bl., 17,88 MB) Ilmenau : Techn. Univ., Diss., 2014

In der vorliegenden Arbeit wurde eine Strömungszelle für insitu mikrogravimetrische Untersuchungen entwickelt und charakterisiert. Während sich an einer rotierenden Scheibenelektrode (RDE) ausbildende homogene Diffusionsgrenzschicht gut für die Charakterisierung von elektrochemischen Prozessen eignet, ist eine in situ Schichtendickenmessung nicht möglich. Dieser gerade für Messungen von Abscheidungsprozessen wichtige Parameter ist mit einer QCM gut messbar, hierbei ist aber die Erzeugung einer homogenen Diffusionsgrenzschicht durch Rotation nur schwer realisierbar. Die Kombination einer Strömungszelle mit der Quarzmikrowaage(QCM) erlaubt die Untersuchung transportabhängiger Metallabscheidungen bei gleichzeitiger insitu Messung der Schichtdickenänderung. Zur Optimierung der Strömungszelle wird die Simulationssoftware "Comsol Multiphysics" verwendet. Mit Hilfe der Simulation werden unterschiedliche Strömungen und der Stoffumsatz der Elektrode berechnet. Zur Charakterisierung wird die Grenzstromdichte des Redoxsystem HexacyanoferratII/III an der RDE verwendet. Die Ergebnisse der QCM in der Strömungszelle werden jeweils mit den Simulationsergebnissen und den Versuchsergebnissen der RDE verglichen und ausgewertet. Als wichtigste technische Anwendung wird die autokatalytische Nickelphosphorabscheidunguntersucht. Stabilisatoren verhindern eine spontane Elektrolytzersetzung. Die Inhibierung der Abscheidegeschwindigkeit bei unterschiedlichen Stabilisatorkonzentrationen und Strömungsgeschwindigkeiten wird aufgezeigt. Als Stabilisatoren werden Blei und Thioharnstoff verwendet. Im gleichen Aufbau wird der Einfluss der Stabilisatorkonzentration auf dieabgeschiedene NiP-Schicht wird durch eine elektrochemische Auflösung untersucht. Das Auflösepotential der NiP-Schicht nimmt mit höherer Stabilisatorkonzentration im Abscheideelektrolyten ab. Durch Messung des Auflösepotentials können dieNiP-Schicht der hochphosphorhaltigen NiP-Schicht mit 11 Gew.-%, die mittelphosphorhaltige NiP-Schicht mit 7 Gew.-% Phosphor mit und ohne Schwefel unterschieden werden. Der Einfluss der Thioharnstoffkonzentration auf das Auflösepotential erlaubt die Abschätzung der Thioharnstoffkonzentration zwischen 0-0,5 ppmund >1 ppm.



http://www.db-thueringen.de/servlets/DocumentServlet?id=26038
El Mofid, Wassima; Ivanov, Svetlozar; Bund, Andreas;
Effect of synthesis conditions and composition modification on the structural and electrochemical properties of layered transition metal oxide cathode materials. - In: 2014 International Renewable and Sustainable Energy Conference (IRSEC), ISBN 978-1-4799-7337-8, (2014), S. 626-630

http://dx.doi.org/10.1109/IRSEC.2014.7059798
Georgieva, Mihaela; Petrova, Maria; Jakob, Christine; Fritz, Mathias; Chakarova, V.
Electroless copper-SiC and nickel-SiC composite coatings on non-metallic substrates :
Stromlos abgeschiedene Kupfer-SiC- und Nickel-SiC-Kompositbeschichtungen auf nichtmetallischen Substraten. - In: WOMag, ISSN 2195-5891, Bd. 3 (2014), 10, S. 26-27

Grohmann, Lukas; Bund, Andreas; Lammel, Patricia
Thermosonisches Drahtbonden auf galvanisch abgeschiedenen Oberflächen. - In: Jahrbuch Oberflächentechnik, ISSN 0075-2819, Bd. 70 (2014), S. 253-265
Literaturangaben

Altay, Katarzyna;
Untersuchungen zur elektrochemischen Abscheidung von amorphen Kohlenstoffschichten, 2014. - Online-Ressource (PDF-Datei: XII, 371 S., 16,18 MB) Ilmenau : Techn. Univ., Diss., 2014
Enth. außerdem: Thesen

Amorphe Kohlenstoffschichten bestehen aus regellos angeordneten sp 3- und sp 2-hybridisierten Kohlenstoffatomen, mit nahezu beliebig realisierbaren Hybridisierungsverhältnissen und potentiell in die Schicht einzubringendem Wasserstoff und (Nicht-) Metallen. Da die Klasse der amorphen Kohlenstoffschichten über vielfältige Eigenschaften verfügt, wird eine Vielzahl von Anwendungsbereichen mit wirtschaftlicher Bedeutsamkeit bedient. Zum aktuellen Stand der Technik werden amorphe Kohlenstoffschichten hauptsächlich mittels verschiedener Verfahren der Gasphasenabscheidung appliziert, jedoch besteht zunehmend Interesse an einer alternativen Beschichtungsmethode unter atmosphärischen Bedingungen. Einen vielversprechenden Ansatz bietet hierbei die Abscheidung von amorphen Kohlenstoffschichten durch elektrochemische Prozesse aus flüssigen Phasen. Daraus folgt der thematische Schwerpunkt der vorliegenden Arbeit. Die ausgewerteten Veröffentlichungen zeigen einen umfassenden Überblick der Forschungsarbeit in den letzten 20 Jahren und liefern zusammen mit den Untersuchungsergebnissen eine Grundlage zur Beurteilung des aktuellen Forschungsstands. Dies ermöglicht eine realistische Einschätzung des technologischen Potentials dieser Beschichtungsmethode. Die experimentellen Aspekte dieser Arbeit umfassen die Untersuchungen und Auswertungen von neuen Kohlenstoffquelle-Substratmaterial-Kombinationen, auch im Siedetemperaturbereich, und größeren als der bis dahin betrachteten Substratdimensionen. Mit dem speziell für diese Arbeit realisierten experimentellen Aufbau werden wesentliche Aspekte der Prozessführung, insbesondere der Prozesskontrolle nachvollzogen und zahlreiche Parameter untersucht. Ebenso wird vor dem Hintergrund der Wirtschaftlichkeit des Beschichtungsverfahrens hinsichtlich höherer Standzeiten, dasselbe Volumen einer Kohlenstoffquelle über einen längeren Zeitraum eingesetzt. Ein weiteres Einsparpotential wird durch die Verwendung von kostengünstigeren Kohlenstoffquellen mit geringer Chemikalienreinheit überprüft. Die Untersuchungsergebnisse umfassen die Ausarbeitung von Prozessspezifika, Parameterzusammenhängen und der Auswirkungen der Zusammensetzung der Kohlenstoffquelle auf die elektrochemische Abscheidungstechnologie und deren Reproduzierbarkeit. Zusätzlich wird ein Beitrag zu bestehenden Thesen der Schichtbildung sowie der Interpretation von Stromverläufen geleistet.



http://www.db-thueringen.de/servlets/DocumentServlet?id=25496
Ispas, Adriana; Bund, Andreas
Electrochemical quartz crystal microbalance. - In: A - E, (2014), S. 554-568

Bund, Andreas; Ispas, Adriana; Ispas, Adriana *1977-*;
Electrodeposition of reactive elements from ionic liquids. - In: Molten salts chemistry and technology, ISBN 978-1-118-44873-1, (2014), S. 359-364

Schilling, Marco; Schwalbe, Ulf; Szalai, Thomas; Heidrich, Tobias; Endert, Fabian; Ivanov, Svetlozar Dimitrov; Cuibus, Florina
System voltage estimation for a decentralized electromotive drive train system. - In: 16th European Conference on Power Electronics and Applications (EPE '14-ECCE Europe), 2014, ISBN 978-1-4799-3016-6, (2014), S. 2756-2765

http://dx.doi.org/10.1109/EPE.2014.6910991
Gheorghies, Constantin; Rusu, Daniela Ecaterina; Bund, Andreas; Condurache-Bota, Simona; Georgescu, Lucian Puiu
Synthesis and characterization of nickel-diamond nanocomposite layers. - In: Applied nanoscience, ISSN 2190-5517, Bd. 4 (2014), 8, S. 1021-1033
Erratum: Volume 4 (2014), 8, Seite 1035

http://dx.doi.org/10.1007/s13204-013-0285-y
Ivanov, Svetlozar; Grieseler, Rolf; Cheng, Lin; Schaaf, Peter; Bund, Andreas
Electrochemical lithiation of Si modified TiO 2 nanotube arrays, investigated in ionic liquid electrolyte. - In: Journal of electroanalytical chemistry, ISSN 1873-2569, Bd. 731 (2014), S. 6-13

http://dx.doi.org/10.1016/j.jelechem.2014.07.038
Lan, Wen-Jie; Kubeil, Clemens; Xiong, Jie-Wen; Bund, Andreas; White, Henry S.
Effect of surface charge on the resistive pulse waveshape during particle translocation through glass nanopores. - In: The journal of physical chemistry. Energy, materials, and catalysis / American Chemical Society. - Washington, DC : Soc., 2007- , ISSN: 1932-7455 , ZDB-ID: 2256522-X, ISSN 1932-7455, Bd. 118 (2014), 5, S. 2726-2734

http://dx.doi.org/10.1021/jp412148s
Cuibus, Florina Maria; Bund, Andreas; Ilea, Petru
Electrochemical removal of nitrate from waste water. - In: Galvanotechnik, ISSN 0016-4232, Bd. 105 (2014), 7, S. 1398-1407

El Mofid, Wassima; Ivanov, Svetlozar; Konkin, Alexander; Bund, Andreas
A high performance layered transition metal oxide cathode material obtained by simultaneous aluminum and iron cationic substitution. - In: Journal of power sources, ISSN 1873-2755, Bd. 268 (2014), S. 414-422

http://dx.doi.org/10.1016/j.jpowsour.2014.06.048
Wulfmeier, Hendrik; Albrecht, Daniel; Fritze, Holger; Ivanov, Svetlozar; Bund, Andreas
Calorimetric measurement system based on planar temperature sensors for high-temperature investigations on thin films :
Kalorimetrisches Messsystem auf Basis planarer Temperatursensoren für die Untersuchung dünner Schichten im Hochtemperaturbereich. - In: Sensoren und Messsysteme 2014, (2014), insges. 6 S.

Camargo, Magali K.; Schmidt, Udo; Grieseler, Rolf; Wilke, Marcus; Bund, Andreas
Electrodeposition of Zn-TiO2 dispersion coatings: study of particle incorporation in chloride and sulfate baths. - In: Journal of the Electrochemical Society, ISSN 1945-7111, Bd. 161 (2014), 4, Seite D168-D175
Im Titel ist "2" tiefgestellt

http://dx.doi.org/10.1149/2.066404jes
Bund, Andreas; Lange, Ronny; Plieth, Waldfried; Richtering, Werner
Electrodeposition of alloys: application of the Markov chain model to intermetallic compounds. - In: Zeitschrift für physikalische Chemie, ISSN 2196-7156, Bd. 228 (2014), 2/3, S. 269-279

http://dx.doi.org/10.1515/zpch-2014-0469
Strauß, Tina; Sun, Yue;
Messung innerer Spannungen in galvanisch abgeschiedenen Nickel- und Zinkschichten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 105.2014, 2, S. 264, 267-276, insges. 11 S.

Vrublevsky, I. A.; Chernyakova, K. V.; Ispas, Adriana; Bund, Andreas; Zavadski, S.
Optical properties of thin anodic alumina membranes formed in a solution of tartaric acid. - In: Thin solid films, ISSN 1879-2731, Bd. 556 (2014), S. 230-235

http://dx.doi.org/10.1016/j.tsf.2014.01.074
Giridhar, Pulletikurthi; Zein El Abedin, Sherif; Bund, Andreas; Ispas, Adriana; Endres, Frank
Electrodeposition of Niobium from 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ionic liquid. - In: Electrochimica acta, ISSN 1873-3859, Bd. 129 (2014), S. 312-317

http://dx.doi.org/10.1016/j.electacta.2014.02.099
Gruia, Violeta-T.; Ispas, Adriana; Wilke, Marcus; Efimov, Igor; Bund, Andreas
Application of acoustic impedance method to monitoring of sensors: metal deposition on viscoelastic polymer substrate. - In: Electrochimica acta, ISSN 1873-3859, Bd. 118 (2014), S. 88-91

http://dx.doi.org/10.1016/j.electacta.2013.12.010
Ivanov, Svetlozar; Vlaic, Codruta A.; Du, Song; Wang, Dong; Schaaf, Peter; Bund, Andreas
Electrochemical performance of nanoporous Si as anode for lithium ion batteries in alkyl carbonate and ionic liquid-based electrolytes. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 44 (2014), 1, S. 159-168

http://dx.doi.org/10.1007/s10800-013-0619-1
Cuibus, Florina; Bund, Andreas; Ilea, Petru
Electrochemical removal of nitrate from waste water. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, (2014), S. 1-13

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT2910
Ivanov, Svetlozar; Cheng, Lin; Wulfmeier, Hendrik; Albrecht, Daniel; Fritze, Holger; Bund, Andreas
Electrochemical behavior of titania nanotubes in organic carbonate and ionic liquid based Li ion containing electrolytes. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2013-02 (2013), 14, 1146

https://doi.org/10.1149/MA2013-02/14/1146
Vlaic, Codruta Aurelia; Ivanov, Svetlozar Dimitrov; Bund, Andreas
Electrodeposition of thin silicon films as anode materials for lithium ion batteries. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2013-02 (2013), 14, 976

https://doi.org/10.1149/MA2013-02/14/976
Camargo, Magali K.; Schmidt, Udo; Díaz, Isabel; Bund, Andreas
Korrosionsverhalten von chemisch abgeschiedenen Nickel-Phosphor- und Nickel-Phosphor-SiC-Schichten :
Corrosion behavior of electroless nickel-phosphorous and nickel-phosphorous-SiC coatings. - In: WOMag, ISSN 2195-5891, Bd. 2 (2013), 9, S. 21-23

Vlaic, Codruta A.; Ivanov, Svetlozar; Bund, Andreas
Neue Batteriewerkstoffe in der Anwendung - ein Überblick :
Modern applications of new battery materials : overview: new directions for battery materials. - In: WOMag, ISSN 2195-5891, Bd. 2 (2013), 8, S. 4-5

Schmidt, Udo; Lalau, Cornel; Camargo, Magali K.; Lerp, Marianne; Wilke, Marcus; Bund, Andreas
Cathodic corrosion protection of steel by galvanising - basic principles :
Kathodischer Korrosionsschutz von Stahl durch Verzinken - Grundlagen. - In: WOMag, ISSN 2195-5891, Bd. 2 (2013), 2, S. 6

Gavril, Mihaela-Daniela; Schmidt, Udo; Gheorghies, Constantin; Cantaragiu, Alina-Mihaela; Ispas, Adriana; Bund, Andreas
Electrochemical preparation of Co-Cu alloy nanowires and their characterisation. - In: Studia Universitatis Babe¸s-Bolyai, ISSN 0039-3401, Bd. 58 (2013), 3, S. 81-92

Kubeil, Clemens;
Precise settings for coating parameters : numerical simulation of electrochemical processes. - In: International surface technology, ISSN 2192-8703, Bd. 6 (2013), 3, S. 42-43

https://doi.org/10.1365/s35724-013-0209-0
Szalai, Thomas; Schwalbe, Ulf; Heidrich, Tobias; Endert, Fabian; Ivanov, Svetlozar
Decentralized electromotive drive train system using extra low voltage. - In: International Exhibition and Conference on Power Electronics, Intelligent Motion, Renewable Energy and Energy Management (PCIM Europe 2013), (2013), S. 421-427

Krischok, Stefan; Ispas, Adriana; Zühlsdorff, André; Ulbrich, Angela; Bund, Andreas; Endres, Frank
Interaction of Ta and Nb based salts with ionic liquids. - In: DPG-Frühjahrstagung (DPG Spring Meeting) of the Condensed Matter Section [SKM], with its Divisions: Biological Physics, Chemical and Polymer Physics, Crystallography, Dielectric Solids, Dynamics and Statistical Physics, Low Temperature Physics, Magnetism, Metal and Material Physics, Physics of Socio-Economic Systems, Semiconductor Physics, Surface Science, Thin Fils, Vacuum Science and Technology, together with the Divisions: Microprobes, and Radiation and Medical Physics as well as the Working Groups: Industry and Business, and "Young DPG" ; March 10 - 15, 2013, University of Regensburg, 2013, CPP 9.17

Bund, Andreas; Kubeil, Clemens
Double layer effects at nanosized electrodes. - In: Faraday discussions, ISSN 1364-5498, Bd. 164 (2013), S. 339-348

http://dx.doi.org/10.1039/C3FD00050H
Endert, Fabian; Möckel, Andreas; Heidrich, Tobias; Schwalbe, Ulf; Ivanov, Svetlozar D.; Szalai, Thomas
Design and commissioning of a low voltage 25 kw PMSM traction drive. - In: 2013 3rd International Electric Drives Production Conference (EDPC), ISBN 978-1-4799-1102-8, (2013), insges. 5 S.

http://dx.doi.org/10.1109/EDPC.2013.6689760
Thiemig, Denny; Bund, Andreas; Dietrich, Dagmar; Lampke, Thomas
Microstructure and particle incorporation behavior of electrocodeposited Ni-Al2O3 nanocomposites. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, (2013), S. 1-16
Im Titel sind "2" und "3" tiefgestellt

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT513
Ivanov, Svetlozar; Vlaic, Codru¸ta; Du, Song; Wang, Dong; Schaaf, Peter; Bund, Andreas
Nanoporous silicon nanostructures as anode materials for lithium ion batteries. - In: Thüringer Werkstofftag 2013, (2013), S. 205-206
Parallel als Druckausg. erschienen

http://www.db-thueringen.de/servlets/DocumentServlet?id=22997
Vlaic, Codru¸ta; Ivanov, Svetlozar; Yan, Yong; Wang, Dong; Schaaf, Peter; Bund, Andreas
Electrochemical performance of nanoporous silicon nanopillars as anodes for Li-ion batteries. - In: Thüringer Werkstofftag 2013, (2013), S. 211-212
Parallel als Druckausg. erschienen

http://www.db-thueringen.de/servlets/DocumentServlet?id=22997
Fritz, Mathias; Leimbach, Martin; Schmidt, Udo; Bund, Andreas; Kühnlein, Holger H.
Selektive Vorderseitenmetallisierung von Silizium-Solarzellen. - In: Thüringer Werkstofftag 2013, (2013), S. 221
Parallel als Druckausg. erschienen

http://www.db-thueringen.de/servlets/DocumentServlet?id=22997
Heidrich, Tobias; Endert, Fabian; Schwalbe, Ulf; Szalai, Thomas; Ivanov, Svetlozar
Dezentraler Traktionsantrieb für die Kleinspannungsebene. - In: Internationaler ETG-Kongress 2013, (2013), insges. 5 S.

Robotin, B.; Ispas, Adriana; Coman, V.; Bund, Andreas; Ilea, Petru
Nickel recovery from electronic waste II electrodeposition of Ni and Ni-Fe alloys from diluted sulfate solutions. - In: Waste management, ISSN 1879-2456, Bd. 33 (2013), 11, S. 2381-2389

http://dx.doi.org/10.1016/j.wasman.2013.06.001
Szalai, Thomas; Heidrich, Tobias; Schwalbe, Ulf; Endert, Fabian; Ivanov, Svetlozar Dimitrov
Dimensioning of ultra capacitors used for range extension in electric vehicles. - In: 15th European Conference on Power Electronics and Applications (EPE), 2013, ISBN 978-1-4799-0115-9, (2013), insges. 9 S.

http://dx.doi.org/10.1109/EPE.2013.6631735
Uhlemann, Margitta; Tschulik, Kristina; Gebert, Annett; Mutschke, Gerd; Fröhlich, Jochen; Bund, Andreas; Yang, Xuegeng; Eckert, Kerstin
Structured electrodeposition in magnetic gradient fields. - In: European physical journal special topics, ISSN 1951-6401, Bd. 220 (2013), 1, S. 121-130

http://dx.doi.org/10.1140/epjst/e2013-01814-3
Endert, Fabian; Heidrich, Tobias; Schwalbe, Ulf; Szalai, Thomas; Ivanov, Svetlozar D.
Effects of current displacement in a PMSM traction drive with single turn coils. - In: IEEE International Electric Machines & Drives Conference (IEMDC), 2013, ISBN 978-1-4673-4975-8, (2013), S. 160-165

http://dx.doi.org/10.1109/IEMDC.2013.6556248
Wulfmeier, Hendrik; Albrecht, Daniel; Ivanov, Svetlozar; Fischer, Julian; Ulrich, Sven; Bund, Andreas; Fritze, Holger
High-temperature thin-film calorimetry: a newly developed method applied to lithium ion battery materials. - In: Journal of materials science, ISSN 1573-4803, Bd. 48 (2013), 19, S. 6585-6596

http://link.springer.com/article/10.1007/s10853-013-7455-x
Albrecht, Daniel; Wulfmeier, Hendrik; Ivanov, Svetlozar; Bund, Andreas; Fritze, Holger
Electrochemical performance of ionic liquid-molybdenum disulfide Li-ion batteries. - In: Journal of applied electrochemistry, ISSN 1572-8838, Bd. 43 (2013), 6, S. 559-565

http://link.springer.com/article/10.1007/s10800-013-0548-z
Lyutov, Vladimir V.; Ivanov, Svetlozar Dimitrov; Mirsky, Vladimir M.; Tsakova, Vessela T.
Polyaniline doped with poly(acrylamidomethylpropanesulphonic acid): electrochemical behaviour and conductive properties in neutral solutions. - In: Chemical papers, ISSN 1336-9075, Bd. 67 (2013), 8, S. 1002-1011

http://dx.doi.org/10.2478/s11696-013-0341-9
Ivanov, Svetlozar; Cheng, Lin; Wulfmeier, Hendrik; Albrecht, Daniel; Fritze, Holger; Bund, Andreas
Electrochemical behavior of anodically obtained titania nanotubes inorganic carbonate and ionic liquid based Li ion containing electrolytes. - In: Electrochimica acta, ISSN 1873-3859, Bd. 104 (2013), S. 228-235

http://dx.doi.org/10.1016/j.electacta.2013.04.115
Wulfmeier, Hendrik; Albrecht, Daniel; Ivanov, Svetlozar; Fischer, Julian; Grieseler, Rolf; Schaaf, Peter; Ulrich, Sven; Bund, Andreas; Fritze, Holger
Thin film calorimetry - device development and application to lithium ion battery materials. - In: MRS online proceedings library, ISSN 1946-4274, Bd. 1496 (2013), S. 54-59

http://dx.doi.org/10.1557/opl.2013.104
Albrecht, Daniel; Wulfmeier, Hendrik; Ivanov, Svetlozar; Bund, Andreas; Fritze, Holger
Synthesis of different molybdenum disulfide nanostructures and their applicability in lithium ion batteries with ionic liquid electrolytes. - In: MRS online proceedings library, ISSN 1946-4274, Bd. 1496 (2013), S. 1-6

http://dx.doi.org/10.1557/opl.2013.126
Bund, Andreas; Peipmann, Ralf
Elektrochemische Speicher für die Elektrotraktion. - In: Galvanotechnik, ISSN 0016-4232, Bd. 104 (2013), 2, S. 272-275

Camargo, Magali K.; Schmidt, Udo; Bund, Andreas
Study of the electrodeposition of Zn-TiO2 dispersion coatings. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2012-02 (2012), 45, 3296
Im Titel ist "2" tiefgestellt

https://doi.org/10.1149/MA2012-02/45/3296
Bund, Andreas; Fritz, Mathias; Schmidt, Udo; Lühn, Ole; Kühnlein, Holger H.
Novel front side metallization processes for silicon based solar cells. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2012-02 (2012), 47, 3353

https://doi.org/10.1149/MA2012-02/47/3353
Anton, M. S.; Manciulea, A. L.; Schmidt, Udo; Bund, Andreas; Ilea, P.
Hydrometallurgical flow for zinc recovery from Zn-MnO 2 waste batteries : I. zinc solubilization from anodic remnants. - In: Studia Universitatis Babe¸s-Bolyai, ISSN 0039-3401, Bd. 57 (2012), 2, S. 95-102

Gavril, Mihaela-Daniela; Schmidt, Udo; Gheorghies, Constantin; Kups, Thomas; Ispas, Adriana; Bund, Andreas
Electrodeposition of Co and Co-Cu nanowires in porous alumina substrates by pulse and pulse reverse plating. - In: Symposium Anodisieren - vom Korrosionsschutz bis zur Nanotechnologie, (2012), S. 57-63

Hahn, Sebastian; Kilian, A.; Donner, C.; Bund, Andreas
Charakterisierung einer mikrogravimetrischen Strömungszelle zum Studium transportabhängiger Reaktionen der Metallabscheidung. - In: Tagungsband zum Zweiten Workshop Oberflächentechnik, ISBN 978-3-938843-72-7, (2012), S. 34-41

Georgieva, Mihaela; Petrova, Maria; Jakob, Christine; Fritz, Mathias; Chakarova, V.
Obtaining and study of electroless composite coatings Cu-SiC and Ni-SiC on non-metallic substrates. - In: Tagungsband zum Zweiten Workshop Oberflächentechnik, ISBN 978-3-938843-72-7, (2012), S. 32

Gavril, Mihaela-Daniela; Schmidt, Udo; Gheorghies, Constantin; Ispas, Adriana; Kups, Thomas; Bund, Andreas
Electrodeposition of Co-Cu nanowires in alumina templates. - In: Tagungsband zum Zweiten Workshop Oberflächentechnik, ISBN 978-3-938843-72-7, (2012), S. 20-24

Tagungsband zum Zweiten Workshop Oberflächentechnik : 6. und 7. September 2012. - Ilmenau : Technische Universität, 2012. - 89 SeitenVeranstaltungsort: Ilmenau

Kumar, Nanjundan Ashok; Choi, Hyun Jung; Bund, Andreas; Baek, Jong-Beom; Jeong, Yeon Tae
Electrochemical supercapacitors based on a novel graphene/conjugated polymer composite system. - In: Journal of materials chemistry, ISSN 1364-5501, Bd. 22 (2012), 24, S. 12268-12274

http://dx.doi.org/10.1039/C2JM30701D
Ispas, Adriana; Vrublevsky, Igor; Schmidt, Udo; Bund, Andreas
Nanoporous alumina growth in a magnetic field. - In: ECS transactions, ISSN 1938-6737, Bd. 50 (2012), 10, S. 141-146

http://dx.doi.org/10.1149/05010.0141ecst
Krischok, Stefan; Ispas, Adriana; Zühlsdorff, Andre; Ulbrich, Angela; Bund, Andreas; Endres, Frank
Ta and Nb electrodeposition from ionic liquids. - In: ECS transactions, ISSN 1938-6737, Bd. 50 (2012), 11, S. 229-237

http://dx.doi.org/10.1149/05011.0229ecst
Cuibus, Florina Maria; Ispas, Adriana; Bund, Andreas; Ilea, Petru
Square wave voltammetric detection of electroactive products resulting from electrochemical nitrate reduction in alkaline media. - In: Journal of electroanalytical chemistry, ISSN 1873-2569, Bd. 675 (2012), S. 32-40

http://dx.doi.org/10.1016/j.jelechem.2012.04.015
Ispas, Adriana; Bund, Andreas
Pulse plating of tantalum from 1-butyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)amide ionic liquids. - In: Transactions of the Institute of Metal Finishing, ISSN 1745-9192, Bd. 90 (2012), 6, S. 298-304

https://doi.org/10.1179/0020296712Z.00000000058
Cârâc, Geta; Ispas, Adriana
Effect of nano-Al 2 O 3 particles and of the Co concentration on the corrosion behavior of electrodeposited Ni-Co alloys. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 16 (2012), 11, S. 3457-3465

http://dx.doi.org/10.1007/s10008-012-1909-y
Bund, Andreas;
Waldfried Plieth: a tribute on the occasion of his 75th birthday. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 16 (2012), 11, S. 3399-3400

http://dx.doi.org/10.1007/s10008-012-1875-4
Mutschke, Gerd; Tschulik, Kristina; Uhlemann, Margitta; Bund, Andreas; Fröhlich, Jochen
Comment on "Magnetic Structuring of Electrodeposits". - In: Physical review letters, ISSN 1079-7114, Bd. 109 (2012), 22, 229401, insges. 1 S.

https://doi.org/10.1103/PhysRevLett.109.229401
Distelrath-Lübeck, Anika;
Untersuchungen zum Mechanismus der Abscheidung strukturierter Schichten aus sechswertigen Chrom-Elektrolyten, 2012. - Online-Ressource (PDF-Datei: XI, 106 S., 5,91 MB) : Ilmenau, Techn. Univ., Diss., 2012
Parallel als Druckausg. erschienenen

In dieser Arbeit werden die Entstehungsmechanismen strukturierter Hartchromschichten untersucht, die durch ihre einstellbaren tribologischen Eigenschaften für die technische Anwendung interessant sind. Sie entstehen durch Gleichstrom-Abscheidung aus Elektrolyten auf Basis von Chrom(VI)-Oxid, Schwefelsäure und Methansulfonsäure und weisen klar abgegrenzte Bereiche auf, die sich in Schichtaussehen und -dicke unterscheiden. Der Forschungsstand zur Chromabscheidung aus sechswertigen Elektrolyten und zum chemischen Verhalten der Elektrolytbestandteile wird zunächst umfassend dargestellt, analysiert und bewertet. Als Arbeitshypothese wird daraus abgeleitet, dass eine lokal unterschiedliche Inhibition der Kathodenoberfläche durch die bei der Reduktion entstehenden Kathodenfilme der Grund für die Oberflächenstrukturierung sein könnte. Im experimentellen Teil erfolgt die Untersuchung des Elektrolytsystems in Hinblick auf Stromdichte, Abscheidungsdauer, Temperatur und Elektrolytzusammensetzung, den Einfluss der Grundwerkstofftopografie sowie Zusammenhänge zwischen Schichtaussehen und -eigenschaften. Löslichkeit und Zusammensetzung der Kathodenfilme werden untersucht und Elektrolyte mit Hilfe von Stromdichte-Potential-Kurven und galvanostatischen Versuchen charakterisiert. Wesentliche Erkenntnisse sind : - Die Bildung der Flächenanteile der einzelnen Schichtbereiche hängt linear von der mittleren Stromdichte ab. Hingegen wird die Wachstumsgeschwindigkeit der Schichtbereiche von einer jeweiligen lokalen Stromdichte bestimmt. Hieraus wird die Existenz einer diskontinuierlichen Stromdichteverteilung auf der Oberfläche abgeleitet. - Chromsäure und Schwefelsäure wirken bei der Strukturentstehung als Gegenspieler der Methansulfonsäure. Letztere löst die Strukturentstehung aus. Sie führt oft zur Bildung schwerlöslicher Kathodenfilme. - Es besteht ein starker Zusammenhang zwischen der Art des Kathodenfilms und dem Schichtaussehen. Die Chromabscheidung erfolgt zwischen Kathodenoberfläche und Kathodenfilm. Der zum Schichtaussehen führende Oberflächenzustand stellt sich bei Änderung der Abscheidungsbedingungen während der Abscheidung neu ein. - Die Kathodenfilme bestehen wahrscheinlich aus polymeren Chrom(III)-Hydroxokomplexen, die als weitere Liganden Chromat, Sulfat und Wasser enthalten. - Schwefelsäure und Methansulfonsäure beeinflussen unabhängig voneinander die Form der Stromdichte-Potential-Kurve, wobei einem bestimmten Kurvenbereich bei methansulfonsäurehaltigen Elektrolyten die Bildung eines dicken Kathodenfilms zugeordnet werden kann. - In galvanostatischen Versuchen zeigt sich nach wenigen Sekunden eine Strukturierung der Kathode. Sie erreicht nach etwa einer Minute einen stationären Zustand.Die Ergebnisse bestätigen die Hypothese zur Inhibierung durch Kathodenfilme. Aus ihnen wird eine Vorstellung zur Strukturausbildung im Elektrolytsystem Chromsäure-Schwefelsäure-Methansulfonsäure abgeleitet.



http://www.db-thueringen.de/servlets/DocumentServlet?id=20980
Vlaic, Codru¸ta Aurelia; Hühn, C.; Grohmann, L.; Schulze, L.; Ivanov, Svetlozar Dimitrov; Wang, Dong; Schaaf, Peter; Bund, Andreas
Electrochemical behavior of Si nanostructures in ionic liquids. - In: Materials for energy and power engineering, (2012), S. 17-21

http://www.db-thueringen.de/servlets/DocumentServlet?id=20825
Cuibus, Florina;
Electrochemical removal of nitrate from waste water, 2012. - Online-Ressource (PDF-Datei: 127 Bl., 3,95 MB) : Ilmenau, Techn. Univ., Diss., 2012
Parallel als Druckausg. erschienen

Die Produkte der elektrochemischen Reduktion von Nitrat (ERN) hängen entscheidend von der Art des Elektrodenmaterials, dem pH-Wert und dem angelegten Potenzial sowie der Art des Leitsalzes ab. Cu-Sn-Legierungen sind vielversprechende Elektrodenmaterialen, die bis jetzt nicht systematisch untersucht wurden. Aus diesem Grund wurden in dieser Arbeit Cu und Cu-Sn Kathodenmaterialien elektrochemisch hergestellt und auf ihre Eignung für die ERN untersucht. Mit cyclovoltammetrischen Untersuchungen konnten die spezifischen Parameter für die galvanische Abscheidung der einzelnen Metalle bzw. der Legierung optimiert werden. REM-Aufnahmen von Cu-, Sn- und Cu-Sn-Schichten zeigten signifikante strukturelle Veränderungen bei der Variation der elektrochemischen Parameter. Es konnte gezeigt werden, dass die erhaltenen Elektrodenmaterialien gut für Nitratreduktion geeignet sind. In dieser Arbeit wurden zwei einfache und schnelle elektroanalytische Methoden zur Ermittlung der elektroaktiven Spezies verwendet. Für den Nachweis der Reduktionsprodukte wurden Cyclovoltammetrie (CV) bzw. Square-Wave-Voltammetrie (SWV) mit hohen Potentialvorschub-Geschwindigkeiten mit hydrodynamischen Techniken (rotierende Ring-Scheiben-Elektrode) kombiniert. Es konnte gezeigt werden, dass die elektroaktiven Produkte der ERN (NO2-, NH2-OH oder NH4+), mit CV bzw. SWV elektrochemisch nachgewiesen werden können. Mit CV oder SWV ist eine Echtzeit-Auswertung der elektrokatalytischen Eigenschaften der verwendeten Elektrodenmaterialien möglich. Versuchsanlage zur elektrochemischen Reduktion synthetischer Nitrat-LösungenUm ein zuverlässiges Verfahren zur Behandlung von Nitrat Abfällen zu entwickeln, wurde die Rolle der Elektroden-Materialien, Zell-Konfiguration und Betriebsparameter auf die ERN in einem kleinem Durchflussreaktor untersucht. Um die optimalen Bedingungen zu ermitteln, wurden unterschiedliche Betriebsbedingungen wie angelegter Strom, die anfängliche Konzentration von Nitrat und die Durchflussgeschwindigkeit untersucht. Geschwindigkeitskonstanten, Stromausbeuten und Energieverbrauch wurden ausgewertet. Um die maximal erlaubte Nitrat-Konzentration von 50 mg / L zu erreichen, benötigte die Versuchsanlage mit der Cu-Sn-Kathode 16 Stunden, während sie mit der Cu-Kathode 20 Stunden benötigte. Der in dieser Arbeit ermittelte Energieverbrauch für die ERN ist den Literaturdaten überlegen.



http://www.db-thueringen.de/servlets/DocumentServlet?id=20720
Bund, Andreas;
Elektrochemische Grundlagen der Pulsabscheidung. - In: Galvanotechnik, ISSN 0016-4232, Bd. 103 (2012), 3, S. 500-504

Camargo, Magali K.; Diaz, Isabel; Schmidt, Udo; Bund, Andreas
Synthesis, characterization and corrosion resistance of electroless nickel-phosphorus and nickel-phosphorus-SiC coatings: a comparative study. - In: Galvanotechnik, ISSN 0016-4232, Bd. 103 (2012), 1, S. 48-56

Mühlenhoff, Sascha; Mutschke, Gerd; Koschichow, Denis; Yang, Xuegeng; Bund, Andreas; Fröhlich, Jochen; Odenbach, Stefan; Eckert, Kerstin
Lorentz-force-driven convection during copper magnetoelectrolysis in the presence of a supporting buoyancy force. - In: Electrochimica acta, ISSN 1873-3859, Bd. 69 (2012), S. 209-219

http://dx.doi.org/10.1016/j.electacta.2012.02.110
Vrublevsky, Igor; Chernyakova, Katsiaryna; Bund, Andreas; Ispas, Adriana; Schmidt, Udo
Effect of anodizing voltage on the sorption of water molecules on porous alumina. - In: Applied surface science, Bd. 258 (2012), 14, S. 5394-5398

http://dx.doi.org/10.1016/j.apsusc.2012.02.020
Georgieva, Mihaela; Petrova, Maria; Jakob, Christine; Fritz, Mathias
Obtaining of electroless dispersion copper coatings on non-metallic substrates. - In: Tagungsband zum ersten fachübergreifenden Workshop Oberflächentechnik, ISBN 9783938843680, (2012), insges. 1 S.

Rusu, Daniela Ecaterina; Ispas, Adriana; Bund, Andreas; Gheorghies, Constantin; Cârâc, Geta
Corrosion tests of nickel coatings prepared from a Watts-type bath. - In: Journal of coatings technology and research, ISSN 1935-3804, Bd. 9 (2012), 1, S. 87-95

https://doi.org/10.1007/s11998-011-9343-0
Ispas, Adriana; Bund, Andreas
On the electrochemical phase formation in ionic liquids. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2011-02 (2011), 36, 2263

https://doi.org/10.1149/MA2011-02/36/2263
Cuibus, Florina; Dorneanu, Sorin-Aurel; Ispas, Adriana; Bund, Andreas; Ilea, Petru
Square wave voltammetry for the detection of electroactive products resulting from nitrate reduction at a copper-tin alloy electrode. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2011-02 (2011), 41, 2423

https://doi.org/10.1149/MA2011-02/41/2423
Peipmann, Ralf; Niemann, Martin; Mutschke, Gerd; Bund, Andreas; Fröhlich, Jochen
Magnetohydrodynamic impedance spectroscopy: determination of MHD transfer functions. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2011-02 (2011), 41, 2449

https://doi.org/10.1149/MA2011-02/41/2449
Kubeil, Clemens; Bund, Andreas
Influences of bulk conductivity and double layer thickness on IonCurrent rectification in nanopores. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2011-02 (2011), 43, 2532

https://doi.org/10.1149/MA2011-02/43/2532
Ivanov, Svetlozar; Wulfmeier, Hendrik; Schulz, Michał; Fritze, Holger; Ispas, Adriana; Bund, Andreas
TiO2 - amorphous silicon nano-porous structures as a novel anode materials for energy storage applications. - In: Meeting abstracts, ISSN 2151-2043, Bd. MA2011-02 (2011), 12, 596
Im Titel ist "2" tiefgestellt

https://doi.org/10.1149/MA2011-02/12/596
Bund, Andreas;
Elektrochemische Grundlagen der Pulsabscheidung. - In: Innovationstreiber Galvanotechnik und Oberflächentechnik, ISBN 978-3-87480-269-7, (2011), S. 87-91

Kutzschbach, Peter; Strauß, Tina
Untersuchungen zur Hydrodynamik in der Electroplating-Unit. - In: Galvanotechnik, ISSN 0016-4232, Bd. 102 (2011), 9, S. 2084-2089

Vrublevsky, Igor; Chernyakova, Katsiaryna; Ispas, Adriana; Bund, Andreas; Gaponik, Nikolai; Dubavik, Aliaksei
Photoluminescence properties of heat-treated porous alumina films formed in oxalic acid. - In: Journal of luminescence, ISSN 0022-2313, Bd. 131 (2011), 5, S. 938-942

https://doi.org/10.1016/j.jlumin.2010.12.027
Yan, Yan-Gang; Yang, Yao-Yue; Peng, Bin; Malkhandi, Souradip; Bund, Andreas; Stimming, Ulrich; Cai, Wen-Bin
Study of CO oxidation on polycrystalline Pt electrodes in acidic solution by ATR-SEIRAS. - In: The journal of physical chemistry. Energy, materials, and catalysis / American Chemical Society. - Washington, DC : Soc., 2007- , ISSN: 1932-7455 , ZDB-ID: 2256522-X, ISSN 1932-7455, Bd. 115 (2011), 13, S. 16378-16388

http://dx.doi.org/10.1021/jp104181y
Yan, Yan-Gang; Peng, Bin; Yang, Yao-Yue; Cai, Wen-Bin; Bund, Andreas; Stimming, Ulrich
Interfacial water at a CO-predosed platinum electrode: a surface enhanced infrared study with strong hydrogen evolution reaction control. - In: The journal of physical chemistry. Energy, materials, and catalysis / American Chemical Society. - Washington, DC : Soc., 2007- , ISSN: 1932-7455 , ZDB-ID: 2256522-X, ISSN 1932-7455, Bd. 115 (2011), 13, S. 5584-5592

http://dx.doi.org/10.1021/jp104180n
Bozzini, Benedetto; Tondo, Elisabetta; Bund, Andreas; Ispas, Adriana; Mele, Claudio
Electrodeposition of Au from [EMIm][TFSA] room-temperature ionic liquid: an electrochemical and surface-enhanced Raman spectroscopy study. - In: Journal of electroanalytical chemistry, ISSN 1873-2569, Bd. 651 (2011), 1, S. 1-11

http://dx.doi.org/10.1016/j.jelechem.2010.11.015
Ispas, Adriana; Pölleth, Manuel; Hoa Tran Ba, Khanh; Bund, Andreas; Janek, Jürgen
Electrochemical deposition of silver from 1-ethyl-3-methylimidazolium trifluoromethanesulfonate. - In: Electrochimica acta, ISSN 1873-3859, Bd. 56 (2011), 28, S. 10332-10339

http://dx.doi.org/10.1016/j.electacta.2011.04.060
Mutschke, Gerd; Koschichow, Denis; Bund, Andreas; Fröhlich, Jochen; Yang, Xuegeng; Mühlenhoff, Sascha; Eckert, Kerstin
Numerical simulation of transient effects of copper electrolysis in external magnetic fields. - In: Proceedings of the 8th International PAMIR Conference on Fundamental and Applied MHD, (2011), S. 729-733

Mutschke, Gerd; Tschulik, Kristina; Weier, Tom; Uhlemann, Margitta; Bund, Andreas; Alemany, Antoine; Fröhlich, Jochen
On the action of magnetic gradient forces in microstructured copper deposition. - In: Proceedings of the 8th International PAMIR Conference on Fundamental and Applied MHD, (2011), S. 725-728

Kubeil, Clemens; Bund, Andreas
The role of nanopore geometry for the rectification of ionic currents. - In: The journal of physical chemistry. Energy, materials, and catalysis / American Chemical Society. - Washington, DC : Soc., 2007- , ISSN: 1932-7455 , ZDB-ID: 2256522-X, ISSN 1932-7455, Bd. 115 (2011), 16, S. 7866-7873

http://dx.doi.org/10.1021/jp111377h
Stoyanova, A.; Ivanov, S.; Tsakova, V.; Bund, Andreas
Au nanoparticle-polyaniline nanocomposite layers obtained through layer-by-layer adsorption for the simultaneous determination of dopamine and uric acid. - In: Electrochimica acta, ISSN 1873-3859, Bd. 56 (2011), 10, S. 3693-3699

The layer-by-layer adsorption technique was used to prepare polyaniline (PANI)-gold nanoparticles (AuNP) multilayered structures with different AuNP/PANI ratios. By means of microgravimetric measurements it was found that the amount of the adsorbed species depends on the duration of the AuNP adsorption step. At fixed adsorption step durations the amount of both (PANI and AuNP) materials increases linearly with the number of adsorption steps. Two types of PANI-AuNP multilayered nanocomposites with different AuNP/PANI ratio were studied as electrocatalytic materials for dopamine and uric acid oxidation. The sensitivity of PANI-AuNP for dopamine oxidation was found to depend on type of the nanocomposite whereas for uric acid oxidation the sensitivity remained unaffected by the type of the nanocomposite structure. This result is discussed in terms of the different limitations for both oxidation reactions. By means of differential pulse voltammetry experiments linear concentration dependences of the anodic peak currents were observed for both dopamine and uric acid in the concentration ranges 7-148 mol dm-3 and 29-720 mol dm-3, respectively. In the presence of both analytes no interference effects were detected.



http://dx.doi.org/10.1016/j.electacta.2010.09.054
Ispas, Adriana; Peipmann, Ralf; Adolphi, Barbara; Efimov, Igor; Bund, Andreas
Electrodeposition of pristine and composite poly(3,4-ethylenedioxythiophene) layers studied by electro-acoustic impedance measurements. - In: Electrochimica acta, ISSN 1873-3859, Bd. 56 (2011), 10, S. 3500-3506

Composite layers of poly(3,4-ethylenedioxythiophene) and diamond nanoparticles were prepared by an electrocodeposition procedure from an electrolyte containing the monomer 3,4-ethylenedioxythiophene and a suspension of diamond nanoparticles in acetonitrile/water mixtures. For the in situ monitoring of the deposition process we used piezoelectric quartz crystals with gold electrodes as substrates (electrochemical quartz crystal microbalance, EQCM). The inclusion of the diamond particles increases the stiffness of the layers. This effect can be directly quantified via the electroacoustic impedance of the quartz crystal. We use a mean field model for the interpretation of our EQCM data which yields the complex shear modulus of the composite layers. The volume fraction of diamond (as determined by ex situ XPS) enters as a parameter in the evaluation procedure. Finally, we could estimate the solvent content of the composite layers and the shear moduli of the pure dry PEDOT matrix.



http://dx.doi.org/10.1016/j.electacta.2010.09.042
Ispas, Adriana; Matsushima, Hisayoshi; Bund, Andreas; Bozzini, Benedetto
A study of external magnetic-field effects on nickel-iron alloy electrodeposition, based on linear and non-linear differential AC electrochemical response measurements. - In: Journal of electroanalytical chemistry, ISSN 1873-2569, Bd. 651 (2011), 2, S. 197-203

http://dx.doi.org/10.1016/j.jelechem.2010.12.003
Steinhäuser, Edith;
Potential low-cost palladium-alternatives for activating electroless copper deposition. - In: Circuit world, ISSN 1758-602X, Bd. 36 (2010), 3, S. 4-8

https://doi.org/10.1108/03056121011066279
Steinhäuser, Edith; Jakob, Christine
The potential benefits of a chemical "Kick Start" for the autocatalytic electroless copper plating process. - In: Journal for electrochemistry and plating technology, ISSN 2196-0267, Bd. 1 (2010), 2, S. 3-19

http://dx.doi.org/10.12850/ISSN2196-0267.JEPT1123
Steinhäuser, Edith;
Untersuchungen zu Alternativen der Palladiumaktivierung im Prozeß der chemischen Kupferabscheidung. - In: Galvanotechnik, ISSN 0016-4232, Bd. 101 (2010), 3, S. 498-502

Mutschke, Gerd; Tschulik, Kristina; Weier, Tom; Uhlemann, Margitta; Bund, Andreas; Fröhlich, Jochen
On the action of magnetic gradient forces in micro-structured copper deposition. - In: Electrochimica acta, ISSN 1873-3859, Bd. 55 (2010), 28, S. 9060-9066

In order to shed more light on the role of magnetic gradient forces and Lorentz forces on the deposition pattern found recently at copper electrodes, experiments and numerical simulations have been performed in a simple geometry that consists of a single small cylindrical permanent magnet which is placed behind the cathode. The cylinder axis coincides with the magnetization direction and points normal to the electrode surface. The electrode is oriented vertically which allows a separate discussion of the influence of both forces. - Experiments and numerical simulations are found to give very good qualitative agreement with respect to the deposition pattern. Our analysis clearly shows that the major influence is due to the action of the magnetic gradient force. Numerical simulations prove that the separate action of the Lorentz force does not reproduce the deposition structure. A detailed analytical discussion of the motion forced by the different magnetic forces in superposition with natural convection is given.



http://dx.doi.org/10.1016/j.electacta.2010.08.046
Peipmann, Ralf; Lange, Ronny; Kubeil, Clemens; Mutschke, Gerd; Bund, Andreas
Magnetic field effects on the mass transport at small electrodes studied by voltammetry and magnetohydrodynamic impedance measurements. - In: Electrochimica acta, ISSN 1873-3859, Bd. 56 (2010), 1, S. 133-138

The effect of moderate magnetic fields (up to 0.75 T) on the redox reaction of the ferro-ferricyanide couple at small disk electrodes (radii 12.5, 50 and 800 m) has been investigated using voltammetric techniques and the magnetohydrodynamic (MHD) transfer function analysis. A special feature of the experimental setup is that it works in the time domain and therefore does not need a lock-in amplifier. The magnetic field was applied parallel to the electrode surface and perpendicular to the gravity force. Special focus was given to the influence of the electrode size and the concentrations of the redox species on the MHD effect. In accordance with literature it was found that the MHD effect decreases with decreasing electrode size and concentration of the electroactive species. Furthermore it was found that the characteristic time constant of the MHD effect increases with decreasing concentration of the electroactive species. Combining the information from the voltammetric and the MHD transfer function data we could estimate the magnetically induced flow velocities which were in a reasonable order of magnitude. The implications of our results for MHD stirring in small feature sizes will be discussed shortly.



http://dx.doi.org/10.1016/j.electacta.2010.09.033
Ispas, Adriana; Bund, Andreas; Vrublevsky, Igor
Effects of a magnetic field on growth of porous alumina films on aluminum. - In: Electrochimica acta, ISSN 1873-3859, Bd. 55 (2010), 13/22, S. 4180-4187

The effects induced by a magnetic field on the oxide film growth on aluminum in sulfuric, oxalic, phosphoric and sulfamic acid, and on current transients during re-anodizing of porous alumina films in the barrier-type electrolyte, were studied. Aluminum films of 100 nm thickness were prepared by thermal evaporation on Si wafer substrates. We could show that the duration of the anodizing process increased by 33% during anodizing in sulfuric acid when a magnetic field was applied (0.7 T), compared to the process without a magnetic field. Interestingly, such a magnetic field effect was not found during anodizing in oxalic and sulfamic acid. The pore intervals were decreased by ca. 17% in oxalic acid. These findings were attributed to variations in electronic properties of the anodic oxide films formed in various electrolytes and interpreted on the basis of the influence of trapped electrons on the mobility of ions migrating during the film growth. The spin dependent tunneling of electrons into the surface layer of the oxide under the magnetic field could be responsible for the shifts of the current transients to lower potentials during re-anodizing of heat-treated oxalic and phosphoric acid alumina films.



http://dx.doi.org/10.1016/j.electacta.2010.02.066
Rusu, Daniela Ecaterina; Ispas, Adriana; Bund, Andreas; Gheorghies, Constantin; Carac, Geta
Microstructure and corrosion resistance for the electrodeposited nickel from watts-type baths. - In: Journal of optoelectronics and advanced materials, ISSN 1454-4164, Bd. 12 (2010), 6, S. 1372-1377

Electrodeposition processes using direct current (DC) require the use of additives to control deposit structure and properties as well as current distribution. This work presents a study on the influence of electrodeposited nickel prepared from a Watts bath at different current density ranging from 1 Adm-2 to 10 Adm-2 at pH = 4. The structure of the nickel layers was investigated by scanning electron microscopy (SEM). Vickers hardness of deposited layers was also investigated. The electrochemical behaviour of the nickel layers was investigated by polarization potentiodynamic and electrochemical impedance spectroscopy methods. Protection level against corrosion was evaluated by polarization curves and Electrochemical Impedance Spectroscopy (EIS). Important results include the formation of uniform deposits showing fine grain and excellent protection against corrosion.



Ispas, Adriana; Bund, Andreas; Vrublevsky, Igor
Investigations on current transients in porous alumina films during re-anodizing using the electrochemical quartz crystal microbalance. - In: Journal of solid state electrochemistry, ISSN 1433-0768, Bd. 14 (2010), 11, S. 2121-2128

Current transients and mass variations in asprepared and heattreated anodic alumina films were measured during reanodizing by means of voltammetry and electrochemical quartz crystal microbalance (EQCM), respectively. Aluminum electrodes (100 nm) on quartz crystals were prepared by thermal evaporation. Anodic alumina films were formed on the surface of Al electrodes in aqueous solutions of oxalic (0.3 M) and phosphoric (0.6 M) acid in the potentiostatic regime. The EQCM experiments did not detect an overshoot in the mass variation of the Al electrode during reanodizing of heattreated anodic alumina films. The observed current overshoot in transients proved the presence of electrons and electron holes injected from the contacts in the bulk of the oxide. This can be explained by the emergence of excess electrons in the barrier layer of the alumina films due to a change in the mobility of the electrons.



http://dx.doi.org/10.1007/s10008-010-1043-7
Bund, Andreas; Ispas, Adriana
Ionic liquids as novel reactive media for electrodeposition. - In: Symposium Galvanik - eine etablierte Technik innovativ angewendet, (2010), S. 39-44

Electrodeposition of thin Ta layers with thicknesses from some nm up to 1 m has been investigated in the ionic liquids 1-butyl- 1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide, ([Py1,4]-TFSA) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) amide, ([EMIM] TFSA). It could be shown that Ta electrodeposition occurs in several steps and that not all the time the deposited species are elemental Ta. By increasing the temperature the quality of the deposited layers can be improved significantly. Moreover, the deposition potential influences strongly the morphology and structure of the deposits.



Petrova, Maria; Noncheva, Zoja; Jakob, Christine; Mache, Thomas
Chemische Abscheidung von Nickel-Phosphor-Dispersionsschichten hoher Schichtdicke. - In: Galvanotechnik, ISSN 0016-4232, Bd. 101 (2010), 7, S. 1498-1502

Petrova, Maria; Noncheva, Zoja; Jakob, Christine; Mache, Thomas
Chemische Abscheidung von Nickel-Phosphor-Dispersionsschichten hoher Schichtdicke. - In: Produktion von Leiterplatten und Systemen, ISSN 1436-7505, Bd. 12 (2010), 8, S. 1764-1768

VERDIAN : Abschlussbericht der TU Ilmenau. - Ilmenau. - Online-Ressource (96 S., 4 MB)Förderkennzeichen BMBF 03WKY01M. - Verbund-Nr. 01049006

https://edocs.tib.eu/files/e01fb10/633975176.pdf
Ispas, Adriana; Adolphi, Barbara; Bund, Andreas; Endres, Frank
On the electrodeposition of tantalum from three different ionic liquids with the bis(trifluoromethyl sulfonyl) amide anion. - In: Physical chemistry, chemical physics, ISSN 1463-9084, Bd. 12 (2010), 8, S. 1793-1803

http://dx.doi.org/10.1039/B922071M
Steinhäuser, Edith;
Untersuchungen zu Eigenschaften und Entwicklung formalinfreier chemischer Kupferbäder, 2010. - 172 S. : Ilmenau, Techn. Univ., Diss., 2010
Enth. außerdem: Thesen

Außenstromlos arbeitende, chemische Kupferelektrolyte haben bei der Metallisierung in der Leiterplattenindustrie eine große Bedeutung. Dabei werden fast ausnahmslos formalinhaltige Elektrolyte verwendet. Trotz bekannter umwelt- und gesundheitsschädigender Wirkung des Formaldehyds sind diese Bäder erfolgreich, nicht zuletzt wegen der guten Kosteneffizienz, der Qualität der Kupferschichten und der einfachen sowie zuverlässigen Handhabung. Aber die immer strenger werdenden Umweltrichtlinien erfordern neue Perspektiven im Bereich der chemischen Kupferabscheidung. Für den Ersatz von Formaldehyd sind bereits viele alternative Reduktionsmittel beschrieben und untersucht worden. Dennoch gibt es bisher kein formalinfreies chemisches Kupferbad, das kommerziell mit Erfolg eingesetzt wird. Die Gründe hierfür sind vor allem enge Arbeitsbereiche der Kupferelektrolyte, die unzureichende Bedeckung der Basismaterialien, die unvollständige Reduktion der Kupferionen aus dem Komplex und die Abscheidung von sehr dünnen Kupferschichten, da kein autokatalytischer Abscheidungsprozess vorliegt. Darüber hinaus können störende Nebenprodukte und Instabilitäten im Elektrolyten auftreten. Einige der Alternativen für Formaldehyd sind ebenso umwelt- und gesundheitsschädlich und zudem noch sehr kostenintensiv. In dieser Arbeit werden umweltfreundliche Reduktionsmittel vorgestellt und bezüglich der Fähigkeit zur autokatalytischen Kupferabscheidung überprüft. Es wird eine Kombination und Variation ausgewählter Komplexbildner mit den jeweiligen Reduktionsmitteln durchgeführt, um die Eignung im Prozess der formalinfreien chemischen Kupferabscheidung zu untersuchen. Darauf basierend werden einzelne formalinfreie Kupferbäder entwickelt. Über chemische und elektrochemische Untersuchungen sowohl der Badbestandteile als auch während des Abscheidungsprozesses können die formalinfreien Kupferelektrolyte charakterisiert und analysiert werden. Ihre Wirkungs- bzw. Arbeitsweise und die Eigenschaften der Kupferschichten werden mit formalinhaltigen Kupferbädern verglichen. Das Reduktionsmittel Glyoxylsäure stellt aufgrund ähnlicher chemischer Eigenschaften zu Formaldehyd eine adäquate Alternative für den formalinfreien autokatalytischen Prozess der Kupferabscheidung dar. Glyoxylsäure ist nicht nur mit den bereits vorhandenen Aktivierungsmethoden einsetzbar, sondern auch mit vielen variablen Elektrolytbestandteilen kombinierbar. Die dabei favorisierten Komplexbildner sind HEDTA und Sorbit. Spezielle Elektrolytzusätze, insbesondere Natriumhypophosphit, welches die Initialphase der Kupferabscheidung unterstützt, ermöglichen die Optimierung der glyoxylsäurehaltigen Kupferelektrolyte hinsichtlich der zu erzielenden Anforderungen (z. B. hohe Abscheidungsgeschwindigkeit).



Mache, Thomas; Jakob, Christine; Dittrich, Lars; Hoffmann, Martin
Batch-taugliche Fertigungsansätze für funktionenintegrierende feinwerktechnische Systemkomponenten mit maßgeschneiderten Eigenschaften. - In: Thüringer Werkstofftag 2010, (2010), S. 79-84
Parallel als Druckausg. erschienen

http://www.db-thueringen.de/servlets/DocumentServlet?id=15197
Wilke, Marcus; Schmidt, Udo; Lerp, Marianne; Schlütter, F.; Romanus, Henry; Remdt, Elvira; Teichert, Gerd
Erhöhung der Verschleiß- und Korrosionsbeständigkeit passivierter Trommelware durch Hartstoffpartikeleinbau. - In: Thüringer Werkstofftag 2010, (2010), S. 195
Parallel als Druckausg. erschienen

Der Druck durch die weltweit immer strenger werdenden Umweltverordnungen sowie Qualitäts-anforderungen führte in den letzten Jahren bei vielen Oberflächen-Schutzsystemen zu Umstel-lungen. Im Bereich der Automobilindustrie, die eine der wichtigsten Kundengruppen der Oberflächentechnik darstellt, wurde 2007 im Rahmen der EU-Altautoverordnung der Einsatz von hexavalentem Chrom in allen Fahrzeugbauteilen verboten. Somit ist die Anwendung der über die Jahre entwickelten und durch sehr gute Korrosionsschutzeigenschaften gekennzeichneten Chrom(VI)-haltigen Gelb-, Schwarz- sowie Olivchromatierungen für Zink- und Zinklegierungsschichten, die das mengenmäßig größte Metallisierungsverfahren in der Galvanotechnik darstellen, stark eingeschränkt. Aufgrund des Cr(VI)-Verbotes werden heute neben Blaupassivierungen vor allem Dickschichtpassivierungen eingesetzt. Ohne den für Cr(VI)-haltige Schichten beschriebenen "Selbstheilungseffekt" sind diese Schichtsysteme aufgrund ihrer geringen Härte anfällig bezüglich mechanischen Verletzungen, so dass speziell bei Trommelware die geforderten Korrosionsschutzeigenschaften nur durch zusätzliche silikatische oder organische Topcoats erreicht werden können. Der Beitrag soll zeigen, wie durch die Einlagerung von Hartstoffpartikeln in die Passivierungsschicht die Verschleißbeständigkeit und hierüber durch die Vermeidung von Verletzungen während der Herstellung sowie des Bauteiltransportes auch die Korrosionsbeständigkeit erhöht werden kann. Im Vergleich zu bereits am Markt erhältlichen SiO2-haltigen Dickschichtpassivierungen, die lediglich eine Anlagerung im oberflächennahen Bereich zeigen, konnte durch die Verwendung von Al2O3-Hartstoffpartikeln ein Einbau über die gesamte Schicht realisiert werden. Die abgeschiedenen Schichtsysteme werden mittels optischer Glimmentladungsspektroskopie (GDOES), Rasterelektronenmikroskop (REM) sowie Transmissionselektronenmikroskop (TEM) charakterisiert. Ein Vergleich zum Einbauverhalten weiterer Hartstoffpartikel (Metall-Oxide, -Nitride, -Carbide) findet satt. Durch eine geeignete Partikelvorbehandlung sowie sterische Stabilisierung konnte die Agglomeration der Hartstoffpartikel im stark sauren Milieu der Passivierungslösung sowie bei den hohen Ionendichten unterdrückt werden. Hierdurch sind wichtige Voraussetzungen für einen industriellen Einsatz als innovatives Passivierungsverfahren verzinkter Massenware geschaffen worden. Weitere Einflussfaktoren auf den Partikeleinbau sowie die Partikelstabilität werden diskutiert.



http://www.db-thueringen.de/servlets/DocumentServlet?id=15197
Dittrich, Lars; Mache, Thomas; Hoffmann, Martin;
Batch-taugliche Fertigungsansätze für feinwerktechnische Sytemkomponenten. - In: Mikro-System-Technik Chemnitz '09, ISBN 978-3-00-029135-7, (2009), S. 85-89

Wulf, Sven-Erik; Böck, Reinhard; Jakob, Christine
Electrodeposition of thin Fe-, Co- and FeCo-layers from choline chloride based deep eutectic solvents (DES). - In: Information technology and electrical engineering - devices and systems, materials and technologies for the future, (2009), insges. 5 S.

http://www.db-thueringen.de/servlets/DocumentServlet?id=15168
Petrova, Maria; Noncheva, Zoya; Jakob, Christine; Mache, Thomas
Electroless deposition of thick Nickel-Phosphor-dispersion coatings. - In: Information technology and electrical engineering - devices and systems, materials and technologies for the future, (2009), insges. 4 S.

http://www.db-thueringen.de/servlets/DocumentServlet?id=14769
Mache, Thomas; Jakob, Christine; Dittrich, Lars; Hoffmann, Martin
Herstellung von funktionsintegrierenden Galvanowerkstoffen mit maßgeschneiderten Eigenschaften für Mikrodirektantriebe. - In: Proceedings, ISBN 978-3-8007-3183-1, (2009), insges. 4 S.

Distelrath, Anika; Jakob, Christine
Investigation of structured electrodeposition of hard chromium coatings. - In: Information technology and electrical engineering - devices and systems, materials and technologies for the future, (2009), S. 379

Kutzschbach, Peter; Li, Yu;
Untersuchung der Hydrodynamik an einer Drei-Spindel-Anlage zur galvanischen Waferbeschichtung. - In: Galvanotechnik, ISSN 0016-4232, Bd. 100 (2009), 7, S. 1514-1520

Fritz, Mathias; Kutzschbach, Peter; Kutzschbach, Peter *1944-*; Jakob, Christine;
Nickelschichten im Durchzugsverfahren : Untersuchungen zur Abscheidung von Metallschichten auf Stahlrohren unter Strömungsbedingungen. - In: Metalloberfläche, ISSN 0026-0797, Bd. 63 (2009), 4, S. 37-39

Dittrich, Lars; Kallenbach, Matthias; Bonitz, Björn; Mache, Thomas; Hoffmann, Martin
Batch-capable fabrication approach for a highly efficient miniaturized magnetic valve. - In: Prospects in mechanical engineering, (2008), insges. 2 S.

http://www.db-thueringen.de/servlets/DocumentServlet?id=18126
Mache, Thomas; Dittrich, Lars; Kallenbach, Matthias; Jakob, Christine
Herstellung von Mikroventilbauteilen für magnetische Mikrodirektantriebe. - In: Vorträge, ISBN 978-3-9806061-7-2, (2008), insges. 6 S.

Die Miniaturisierung technischer Systeme ist ein seit Jahren anhaltender Entwicklungstrend. Ein großes Marktpotential wird von magnetischen Mikrodirektantrieben für die Ventiltechnik erwartet. Da in pneumatischen Steuerungsprozessen die Notwendigkeit zur Miniaturisierung besteht, wurden die Möglichkeiten und Grenzen der Mikrogalvanoformung für die Herstellung von Mikroventilbauteilen im Rahmen des Projektes "Vernetzte integrierte magnetische Direktantriebe" (VERDIAN) untersucht werden. Die Entwicklung von funktionsoptimierten bzw. funktionenintegrierenden Materialien und deren galvanische Abscheidung in mikrostrukturierte Resistmasken bieten dabei eine ideale Möglichkeit zur Volumenreduzierung.



Zimmermann, Yvonne; Neudeck, Andreas; Möhring, Uwe; Höland, Dieter; Weber, Steffen; Petzoldt, Franziska; Schmidt, Udo; Jakob, Christine; Ulrich, Hans-Jürgen
Verkupfern textiler Materialien - vom Labor bis zum Material. - In: Vorträge, ISBN 978-3-9806061-7-2, (2008), insges. 4 S.

Textile Strukturen sind wegen ihrer Flexibilität, Nachgiebigkeit und mechanischen Belastbarkeit ideale Materialien für den Einsatz in der Mikrosystemtechnik und als Basissubstrate für flexible elektronische Strukturen. Metallisierte Fadenmaterialien bilden die Grundlage für die optimale Integration mikroelektronischer Bauteile und Mikrosystemtechnik in Textilien. Sie stellen eine interessante Alternative zu bisher verwendeten Metallfäden dar, weil die textilen Eigenschaften des Basismaterials, welche maßgeblich das mechanische Verhalten bestimmen nahezu vollständig erhalten bleiben. Der Beitrag stellt das Thüringer Verbundvorhaben zum Verkupfern textiler Materialien vor. Im Projekt ist eine Technologie entwickelt worden, mit der Rundgetricke aus Polyester stromlos verkupfert und die Kupferschicht in der Flächenware galvanisch weiter verstärkt werden können. Nach Rückgewinnung des verkupferten Fadens aus dem Gestrick steht dieser der weiteren textilen Verarbeitung zur Verfügung. Zur Realisierung der Verkupferungsschritte sind Spezialanlagen konzipiert worden. Der hochleitfähige verkupferte Polyesterfaden stellt nicht nur selbst innovatives Produkt dar, sondern kann auch Bestandteil einer Reihe innovativer Produkte [1-3] sein. so werden die entwickelten Materialien als textile elektrische Zuleitungen zur Stromversorgung von Haushaltsgeräten und als flexible, knickbruchbeständige Wärmequelle in Heizdecken getestet und damit eine neue Generation derartiger Gebrauchsgegenstände für den Markt vorbereitet.



Fritz, Mathias; Kutzschbach, Peter; Kutzschbach, Peter *1944-*; Jakob, Christine;
Untersuchungen zur Abscheidung von Metallschichten auf Stahlrohren unter Strömungsbedingungen. - In: Vorträge, ISBN 978-3-9806061-7-2, (2008), insges. 6 S.

Es wurden Untersuchungen zur galvanischen Abscheidung von Nickel und Zink auf Stahlrohr unter Strömungsbedingungen mit dem Ziel durchgeführt, durch geeignete Variation der Elektrolytströmung die Beschichtungszeiten durch Anwendung hoher Stromdichten zu verringern. Die erhaltenen Ergebnisse sollen die Grundlage für Beschichtungen in kontinuierlich arbeitenden Durchzugsanlagen für die industrielle Beschichtung von Rohren, Bändern oder Drähten sein. Zur Charakterisierung der Strömung erfolgte im ersten Schritt unter Einsatz eines Redoxelektrolyten die Ermittlung von Stoffübergangszahlen, aus denen die zu erwartende maximale Arbeitsstromdichte unter den jeweiligen Strömungsbedingungen näherungsweise abgeleitet werden können. Im zweiten Schritt wurden Metallabscheidungen aus verschiedenen Elektrolyten und ihre Charakterisierung (Schichtdicke, Rauheit, Duktilität, Härte, Gefüge) vorgestellt. auf spezielle Bedingungen der Vorbehandlung wird kurz eingegangen.



Zimmermann, Yvonne; Neudeck, Andreas; Möhring, Uwe; Petzoldt, Franziska; Schmidt, Udo; Jakob, Christine; Ulrich, Hans-Jürgen; Höland, Dieter; Weber, Steffen
Verkupfern textiler Materialien - vom Labor bis zum Material. - In: Oberflächentechnik für die Praxis, ISBN 978-3-00-025424-6, (2008), S. 51-55

Mache, Thomas;
Herstellung von Mikroventilbauteilen für magnetische Mikroantriebe. - In: Galvanotechnik, ISSN 0016-4232, Bd. 99 (2008), 12, S. 3084-3088

Zimmermann, Yvonne; Neudeck, Andreas; Möhring, Uwe; Petzoldt, Franziska; Schmidt, Udo; Jakob, Christine; Ulrich, Hans-Jürgen; Höland, Dieter; Weber, Steffen
Verkupfern textiler Materialien. - In: Melliand-Textilberichte, ISSN 0341-0781, Bd. 89 (2008), 10, S. 386-387

Zimmermann, Yvonne; Neudeck, Andreas; Möhring, Uwe; Petzoldt, Franziska; Schmidt, Udo; Jakob, Christine; Ulrich, Hans-Jürgen; Höland, Dieter; Weber, Steffen
Verkupfern textiler Materialien. - In: Tagungsband, ISBN 978-3-00-024955-6, (2008), S. 75-79

Günther, Edith; Kutzschbach, Peter; Mache, Thomas; Jakob, Christine
Abscheidung von Palladium und Palladiumlegierungen mit hohen Schichtdicken. - In: Galvanotechnik, ISSN 0016-4232, Bd. 98 (2007), 1, S. 206-212

Metzner, Martin;
Korrelation der Verfahrensparameter und des festkörperphysikalischen Aufbaus sowie der makroskopischen Eigenschaften elektrolytisch generierter Chromsysteme, 2007. - IV, 156 S. : Ilmenau, Techn. Univ., Diss., 2007
Enth. außerdem: Thesen

Gegenstand der Arbeit ist die galvanische Chromabscheidung aus verfahrens- und werkstofftechnischer Sicht. Dies bezieht sich auf die Abscheidung aus verschiedenen sechswertigen Chromelektrolyten mit und ohne Zusatz von keramischen nanoskaligen Partikeln und die Abscheidung aus dreiwertigen Chromelektrolyten. Die theoretischen verfahrenstechnischen Hintergründe der einzelnen Systeme werden dargestellt. Das Augenmerk liegt aber auch auf experimentellen Untersuchungen. Bei deren Auswertung werden grundsätzlich festkörperphysikalische und makroskopische, also den Anwender interessierende Eigenschaften, unterschieden. Im Einzelnen werden die Aspekte Textur, Korngröße, Wasserstoffgehalt, Härte, Risszahl, innere Spannungen und Stromausbeute dargestellt und in Abhängigkeit von den Verfahrensparametern interpretiert. Die Eigenschaften werden dabei nicht nur als einzelnes, sondern in Korrelation zueinander erfasst. Bekannte Phänomene und Zusammenhänge können teilweise bestätigt werden. Andere Zusammenhänge werden aus neuen Blickwinkeln dargestellt, hinsichtlich einiger Aspekte können gänzlich neue Erkenntnisse dargestellt werden.



Petzoldt, Franziska; Schmidt, Udo; Jakob, Christine;
Untersuchungen zur magneto-hydrodynamischen Konvektion an ebenen und mikrostrukturierten Elektroden. - In: Vorträge, (2007), insges. 6 S.

Die zunehmende Miniaturisierung von Bauelementen verursacht auch im Bereich der Fertigungsverfahren und Werkstoffentwicklung einen enormen Forschungsbedarf. Immer geringere Abmessungen gepaart mit höheren Ansprüchen an mechanische, tribologische oder elektrische Eigenschaften stehen dabei im Widerspruch zu massenmarkttauglichen Produkten mit preiswerten Herstellungsverfahren. Einen Kompromiss bietet die moderne Mikrogalvanoformung, auch Lithographisch-Galvanische Abformung (LIGA) genannt. - Um das LIGA-Verfahren effizienter zu gestalten, konzentriert sich die derzeitige Forschung auf die Fragestellung der schnelleren galvanischen Auffüllung von Mikrostrukturen. Zu diesem Zweck ist es wünschenswert eine Konvektion zu erzeugen, die nicht nur im äußeren Elektrolytvolumen, sondern auch in der Nähe der Abscheideoberfläche der zurückgesetzten Elektroden, dass heißt bis innerhalb der Mikrostruktur, wirkt. Diese Arbeit beschäftigt sich mit der Wirkung eines starken homogenen magnetischen Feldes bis maximal 5 Tesla auf die Stofftransportvorgänge an ebenen und mikrostrukturierten Elektroden. Die Untersuchung des magnetohydrodynamischen (MHD) Effektes erfolgte über die Grenzstrommessungen mit verschiedenen Modellelektrolyten. Die in Abhängigkeit von der Magnetfeldstärke gemessenen Grenzströme wurden mit Messungen an der rotierenden Scheibe verglichen. Mit Hilfe eines sauren Kupferelektrolyten wurden Strömungsplastiken auf ebenen Substraten erzeugt, um die Richtung der magnetfeldinduzierten Hydrodynamik zu zeigen. Über die Stärke des sich einstellenden Grenzstromes und das COTTRELL-Verhalten wurde eine Abschätzung der Diffusionsschichtdicke vorgenommen. An den Mikrostrukturen konnte dabei eine Abnahme der Diffusionsschichtdicke kleiner als die Resisthöhe von 500[my]m festgestellt werden.



Günther, Edith; Jakob, Christine; Schmidt, Udo; Petzoldt, Franziska
Stromlose Verkupferung textiler Materialien. - In: Vorträge, (2007), insges. 6 S.

Textile Materialien bieten aufgrund ihrer hohen Flexibilität, Nachgiebigkeit und mechanischen Belastbarkeit vielfältige Einsatzmöglichkeiten. Durch die Kombination dieser Eigenschaften mit den physikalischen Eigenschaften der Metalle können neue Anwendungsbereiche für die metallisierten Textilien erschlossen werden. Der Stand der Technik bezüglich der Metallisierung nicht leitender textiler Substrate beinhaltet insbesondere die Versilberung von textilen Polyamidfasern. Die Anwendung versilberter Polyamidfäden ist auch unter dem Namen "Silbertechnologie" bekannt. Darauf aufbauend soll die chemische Kupferabscheidung auf Polyester angewendet werden, um kostengünstigere und thermisch stabilere Produkte zu erhalten. Einerseits wird Polyester bislang nicht in der Kupferstoffgalvanisierung eingesetzt, anderseits könnten der Literatur auch keine gängigen Beschichtungsmethoden entnommen werden, die einen haftfesten Verbund zwischen Kupfer und Polyester bringen würden. - Es galt herauszufinden, inwieweit bereits vorhandene Technologien der Kunststoffmetallisierung, z.B. für ABS-Polymere, auf Polyestermaterialien übertragbar sind. Die Abscheidungsrate des verwendeten, chemischen Kupferelektrolyten wird in Abhängigkeit der Elektrolytbelastung, der Elektrolyttemperatur, der Konzentration der Hauptbestandteile des Kupferelektrolyten und der Konvektion untersucht. Zur Konstanthaltung der Abscheidungsgeschwindikeit werden die Elektrolytbestandteile analysiert und der Elektrolyt regeneriert. Untersuchungen bezüglich der Haftfestigkeit und Duktilität der chemisch abgeschiedenen Kupferschicht werden dargestellt.



Günther, Edith; Jakob, Christine; Kutzschbach, Peter; Mache, Thomas
Abscheidung von Palladium und Palladiumlegierungen mit hohen Schichtdicken für die Mikrosystemtechnik. - In: Materials science and engineering technology, ISSN 1521-4052, Bd. 38 (2007), 2, S. 116-120

http://dx.doi.org/10.1002/mawe.200600117
Jakob, Christine; Schmidt, Udo;
Magneto-hydrodynamic convection in micro-structures with high aspect ratio. - In: Information technology and electrical engineering - devices and systems, materials and technologies for the future, (2006), insges. 8 S.

http://www.db-thueringen.de/servlets/DocumentServlet?id=13895
Mache, Thomas;
Legierungsabscheidung für die Mikrosystemtechnik unter definierten hydrodynamischen Bedingungen. - In: Information technology and electrical engineering - devices and systems, materials and technologies for the future, (2006), insges. 12 S.

http://www.db-thueringen.de/servlets/DocumentServlet?id=13902
Mache, Thomas; Jakob, Christine
LIGA-4H (16IN0141) - Parameterentwicklung für die schnelle Abscheidung von NiFe in Mikrostrukturen ; [Verbundprojekt: LIGA-Mikrostrukturen aus NiFe-Legierungsgalvanik] ; Abschlussbericht an den Projektträger ; Projektbezeichnung: Eisen- Nickel- Legierungsabscheidung ; PROJEKT-Abschlussbericht. - Ilmenau : Techn. Univ., [Fak. für Elektrotechnik und Informationstechnik, Inst. für Werkstofftechnik, Fachgebiet Elektrochemie- und Galvanotechnik (ECG)]. - Online-Ressource (15 S., 206 KB)Verbund-Nr. 01023041

https://edocs.tib.eu/files/e01fb07/527302562.pdf
Unruh, Jürgen N. M.;
Der Mechanismus der Verchromung und Möglichkeiten der Prozesssteuerung. - 230 S. Ilmenau : Techn. Univ., Habil.-Schr., 2006

Distelrath, Anika; Jakob, Christine; Metzner, Martin
Untersuchungen an Chromdispersionsschichten für tribologische Anwendungen. - In: ZVO Oberflächentage 2006, ISBN 978-3-9806061-6-5, (2006), insges. 4 S.

In Zusammenarbeit zwischen der TU Ilmenau und dem IPA Stuttgart wurde der Einbau von Aluminiumoxidpartikeln in Chromschichten untersucht. - Die Charakterisierung dieser Schichten hinsichtlich der Einbaumenge und der Verteilung erfolgt mit AFM, REM und GDOS Tiefenprofiluntersuchungen. Die Änderung des tribologischen Verhaltens der Schichten durch den Einbau der Partikel wird am tribologischen Prüfstand mit herkömmlichen Chromschichten vergleichen.



Petzoldt, Franziska; Jakob, Christine; Jakob, Christine *1948-2019*;
MHD - Beeinflussung der Konvektion in Mikrostrukturen mit verschiedenen Aspektverhältnissen. - In: ZVO Oberflächentage 2006, ISBN 978-3-9806061-6-5, (2006), insges. 5 S.

Die Abscheidung von verschiedenen Metallen in Mikrostrukturen erfolgt mit steigendem Aspektverhältnis zunehmend diffusionsgesteuert. Die Strukturhöhe entspricht dabei weitgehend der Diffusionsschichtdicke für den Antransport der Ionen. Insbesondere für die Mitabscheidung von nanoskaligen Partikeln wäre eine konvektive Bewegung innerhalb der Struktur wünschenswert. Am Beispiel von Redoxelektrolyten werden Diffusionsgrenzstromdichten in Abhängigkeit von der Stärke eines äußeren Magnetfeldes ermittelt. Die Stärke der konvektiven Bewegung durch die induzierte Lorenzkraft wird durch den steigenden Diffusionsgrenzstrom des Redoxsystems angezeigt. Der Einfluss von Richtung und Stärke des Magnetfeldes auf den Diffusionsgrenzstrom wird ermittelt und im elektrochemischen Abscheidungsprozess erste Versuche mit dem Einbau von Nanopartikeln vorgestellt.



Mache, Thomas;
Definierte Legierungsabscheidungen für die Mikrosystemtechnik. - In: ZVO Oberflächentage 2006, ISBN 978-3-9806061-6-5, (2006), insges. 15 S.

Die heutige Mikrosystemtechnik des 21. Jahrhundert verlangt immer mehr nach Werkstoffen vor allem Legierungen mit definiert einstellbaren Zusammensetzungen und Eigenschaften. Bei der Herstellung dieser Legierungen ist nicht nur die hohe Reproduzierbarkeit eine Forderung sondern auch deren schnelle Fertigung. Dabei muss man besonders die Beschichtungszeit und Beschichtungstemperatur berücksichtigen, da die hohe Präzision bzw. Legierungszusammensetzung möglichst über die gesamte Bauteilhöhe von mehreren 100 æm bis him zu wenigen mm erhalten bleiben sollte. In diesem Beitrag werden die Probleme und Lösungsvorschläge zur Fertigung von Mikrobauteilen aus Legierungen des anormalen Legierungssystems von Nickel Eisen dargelegt. Das System zeichnet sich besonders durch die starke Abhängigkeit der Legierungszusammensetzung von der Diffusionsschichtdicke aus.



Günther, Edith; Jakob, Christine; Kutzschbach, Peter; Mache, Thomas
Abscheidung von Palladium und Palladiumlegierungen mit hohen Schichtdicken für die Mikrosystemtechnik. - In: Verbundwerkstoffe und Werkstoffverbunde, (2006), S. 211-225

Die Abscheidung von Metallen und Legierungen in Mikrostrukturen erfordert meist eine Schichtdicke größer als 100 [My]m, die der Strukturhöhe entspricht. Für die Nutzung von Edelmetallen in Mikrosystemen ist die Abscheidung von spannungsarmen, rissfreien, porenfreien und duktilen Schichten notwendig. Da die kommerziell abgeschiedenen Edelmetallschichten nur bis etwa 10 [My]m qualitätsgerecht abgeschieden werden können, sind geeignete Zusätze und Variation der Abscheidungsbedingungen erforderlich, um mikrosystemtaugliche Elektrolyte zu entwickeln. Charakterisierung der Schichteigenschaften, Parameter der Abscheidungstechnologie und Anwendungsbeispiele werden aufgegührt. Erste Ergebnisse werden vorgestellt und diskutiert.



Hupel, Christian;
Vergleichende Untersuchung elektrochemischer und gravimetrischer Methoden zur Korrosionsgeschwindigkeitsbestimmung von Eisen, Kupfer und Zink in wässrigen Medien. - In: Verbundwerkstoffe und Werkstoffverbunde, (2006), S. 203-210

Da im Verlauf der Korrosionsforschung verschiedene Methoden der Korrosionsgeschwindigkeitsmessung entwickelt wurden und sich bis heute keine dieser Messungen als die bessere oder genauere durchsetzen konnte, werden in der aktuellen Literatur diese verschiedenen Methoden mit ihren Ergebnissen parallel veröffentlicht. Die Aufgabenstellung dieser Arbeit ist die vergleichende Untersuchung zweier ausgewählter Verfahren der Korrosiongeschwindigkeitsprüfung und die spätere Diskussion der hierbei ermittelten Ergebnisse. Zum Vergleich wurden die beiden dominierenden Verfahren der Messung der Korrosionsgeschwindigkeit herangezogen. Durch einen Langzeittest mit in verschiedenen Medien eingetauchten Proben aus Fe, Cu und Zn konnte nach bestimmten Zeitabständen der Masseverlust der Probe gravimetrisch ermittelt werden. Die Bestimmung der Korrosionsgeschwindigkeit durch elektrochemische Methoden aus der Stromdichtepotenzialkurve und die darauf folgende Berechnung des Polarisationswiderstandes ermöglichten den Vergleich und die Bewertung der beiden Methoden zur Messung der Korrosion.



Oberseider, Michael; Jakob, Christine; Petrova, Maria; Noncheva, Z.; Schawohl, Jens
Untersuchung von chemisch abgeschiedenen nanoskaligen Nickeldispersionsschichten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 96 (2005), 5, S. 1214-1224

Cimalla, Volker; Lebedev, Vadim; Kaiser, Ute; Goldhahn, Rüdiger; Förster, Christian; Pezoldt, Jörg; Ambacher, Oliver
Polytype control and properties of AlN on silicon. - In: Physica status solidi, ISSN 1610-1642, Bd. 2 (2005), 7, S. 2199-2203

http://dx.doi.org/10.1002/pssc.200461579
Jakob, Christine;
Naturwissenschaftliche und technische Grundlagen von Brennstoffzellen. - In: Konferenz Wasserstoff und Brennstoffzellen, (2005), insges. 6 S.

Erler, Frank;
Herstellung und Eigenschaften von Nickeldispersionswerkstoffen mit nanoskaligen Oxidkeramikpartikeln, 2005. - Online-Ressource (PDF-Datei: 148 S., 11,7 MB) : Ilmenau, Techn. Univ., Diss., 2005
Parallel als Druckausg. erschienen

Der Fortschritt in der Mikrotechnik fordert die Entwicklung neuer funktioneller Werkstoffe für die Erweiterung der technischen Einsatzfelder von Mikrobauteilen bei vertretbaren Kosten. Die Mitabscheidung von nanoskaligen Partikeln bei der galvanischen Beschichtung kann diese Weiterentwicklung fördern. Die vorliegende Arbeit liefert hierzu einen Beitrag mit oxidkeramischen Partikeln aus Al2O3 und TiO2. Der Primärteilchendurchmesser der zusammen mit einem konventionellen Watts-Nickelelektrolyten abgeschiedenen Partikel liegt im Bereich von 10 bis 30 nm. Für die galvanischen Prozesse wurde eine spezielle Laboranlage konzipiert. Theoretische Überlegungen zu den Mechanismen des Partikeltransports in Elektrolyten und den hydrodynamischen Bedingungen während der Abscheidung führten zu einer Modellvorstellung über die Konzentrationsverhältnisse der Partikel bei fortschreitender Dispersionsabscheidung in tiefe Mikrostrukturen. Der Einbau von nanoskaligen Partikeln bei der Abscheidung in Strukturen mit hohen Aspektverhältnissen konnte in der modellhaft vorhergesagten Größenordnung nachgewiesen werden. Das Verhalten der nanoskaligen Partikel in Abhängigkeit von der Konzentration der Bestandteile eines Watts-Nickelelektrolyten wurde untersucht. Zur Messung des mittleren Teilchendurchmessers und des Zetapotentials kam ein "Malvern Zetasizer 3000HS(r)" zum Einsatz. Insbesondere Nickelsulfat führt schon bei geringsten Konzentrationen zu einem verstärkten Agglomeratwachstum. Eine Messmethode zur schnellen und einfachen Bewertung der Einbaurate von Partikeln mit der Photonenkorrelationsspektroskopie (PCS) ist entwickelt und verifiziert worden. Der Einfluss der Anwesenheit von Partikeln auf die Kristallisation, die inneren Spannungen und Textur der abgeschiedenen Nickelschichten wurde mit verschiedenen Methoden wie z.B. Streifenkontraktometer, Transmissionselektronenmikroskopie (TEM) und Röntgendiffraktometrie (XRD) untersucht. Ausgehend von Partikeln konnten Zwillingskristalle beobachtet werden, die möglicherweise durch innere Spannungen hervorgerufen wurden. Weitere Eigenschaften der nano-Dispersionsschichten werden im Vergleich zu partikelfrei abgeschiedenen Nickelschichten dargestellt.



http://www.db-thueringen.de/servlets/DocumentServlet?id=5308
Schmidt, Udo;
Prozesskontrolle von galvanischen Elektrolyten mittels LC-MS. - In: Vorträge, (2005), insges. 9 S.

Ziel der Untersuchungen ist es, die Themenschwerpunkte des Fachgebietes Elektrochemie und Galvanotechnik - Dispersions- und Nickellegierungsabscheidung - mit den chemisch-analytischen Methoden zu unterstützen, die eine Reproduzierbarkeit und Konstanz der Abscheidungsbedingungen gewährleisten, insbesondere mittels LC-MS (der Kopplung von Flüssigchromatografie und Massenspektrometrie). - Bezüglich des Analysenverfahrens erfolgt eine kurze Einführung zu den Analysenmöglichkeiten, den Vor- und Nachteilen des Verfahrens sowie zum Nachweis und zur Identifikation einzelner Verbindungen. Die Leistungsfähigkeit der LC-MS wird anhand des Nachweises ausgewählter Zusätze von Nickelelektrolyten wie Netzmitteln, Pyridinium-Verbindungen, Butindiol-Derivaten und Sachharin gezeigt. Neben der Analyse der Einsatzchemikalien, den Einebnern und Glanzbildnern, wird insbesondere auf die qualitative Identifikation der gebildeten Umsetzungsprodukte eingegangen.



Mache, Thomas;
Edelmetallabscheidung für die Mikrosystemtechnik unter definierten hydrodynamischen Bedingungen. - In: Vorträge, (2005), insges. 12 S.

Die schnelle Entwicklung der Mikrosystemtechnik macht es erforderlich die zur Zeit standardisierten Technologien der Galvanotechnik den Bedürfnissen der Mikrotechnik anzupassen. Die Entwicklung und Überführung in Industrieanwendungen von zukunftsweisenden Technologien wie das LIGA-Verfahren spielen dabei eine bedeutende Rolle. Die Forderungen betreffen sowohl hohe Präzision der Mikrobauteile als auch das Abscheiden sehr hoher Schichtdicken reiner Edelmetalle größer 200 æm. Diese müssen zudem noch spezielle Eigenschaften wie hohe Härte, niedrige innere Spannungen und gleichmäßige Verteilung der Schichtdicke über der Gesamtstruktur aufweisen. Für die Abscheidung in LIGA-Strukturen wurde eine speziell auf die Edelmetallabscheidung zugeschnittene Strömungszelle konstruiert und erfolgreich erprobt. Dabei werden die Anforderungen, der konstruktive Aufbau und die Erprobung vorgestellt. Die Untersuchung der hydrodynamischen Bedingungen in der Versuchszelle ist ein wichtiger Aspekt für die anschließende Edelmetallabscheidung, da diese sowohl einen starken Einfluss auf die erzielten Schichteigenschaften als auch auf den Edelmetallverbrauch haben. Um die erzwungene Strömungsverteilung vor der Katode nachweisen zu können, wurden als eine Untersuchungsmethode Strömungsplastiken mit Modellelektrolyten auf der Katodenoberfläche erzeugt und qualitativ visuell bewertet. Eine quantitative Messung der Strömungsbedingungen vor der Katode erfolgte über die Bestimmung der Schichtzusammensetzung bei anormaler Legierungsabscheidung. Dieser Typ zeichnet sich durch eine starke Abhängigkeit der Legierungszusammensetzung von der Diffusionsschichtdicke und somit auch von der Hydrodynamik aus. Als Modellelektrolyt wurde ein NiFe-Elektrolyt gewählt. Bei ansonsten konstant gehaltenen Bedingungen kann indirekt über die Schichtzusammensetzung (Fe-Gehalt) bei bekannter Konvektion auf die Strömungsgeschwindigkeiten vor der katode geschlossen werden. Mit dieser Methode ist es möglich, Aussagen über Strömungsverteilung mit einer sehr hohen Ortsauflösung zu treffen. Mit dieser Zelle konnten LIGA-Mikrostrukturen mit Gold der Härte 200 HV 0,05 und einer Strukturhöhe von > 200 æm gleichmäßig gefüllt werden.



Jakob, Christine;
Potentiale der Elektrochemie sichern die Zukunft. - In: Neue Materialien und Verfahren in der Beschichtungstechnik, (2005), S. 8-12

Kutzschbach, Peter;
Ausgewählte Methoden zur Charakterisierung der hydrodynamischen Bedingungen bei der elektrolytischen Metallabscheidung. - In: Galvanotechnik, ISSN 0016-4232, Bd. 96 (2005), 3, S. 560-570

Eine wichtige Kenngröße der elektrochemischen Metallabscheidung ist die Hydrodynamik vor der Elektrode, die vor allem bei stark strukturierten Oberflächen, Mikrosystemen oder auch der Legierungsabscheidung eine erhebliche Rolle bei der Erzielung von zufriedenstellenden Ergebnissen spielt. Zur Erfassung der entsprechenden Kenngrößen dienen Methoden wie die Diffusionsgrenzstrommessung oder die diffusionskontrollierte Abscheidung bzw. Auflösung. Die Durchführung und Auswertung der Ergebnisse wird an einem sauren Kupferelektrolyten demonstriert. Mit der Sichtbarmachung von Strömungsbildern in Form von Strömungsmessungen wird vor allem dem Praktiker eine Möglichkeit der unkomplizierten Erfassung von Strömungsverhältnissen vor Elektroden aufgezeigt.



Kaiser, Ute; Muller, David A.; Chuvilin, Andrey; Pasold, Gunnar; Witthuhn, Wolfgang
The formation of clusters and nanocrystals in Er-implanted hexagonal silicon carbide. - In: Microscopy and microanalysis, ISSN 1435-8115, Bd. 10 (2004), 2, S. 301-310

http://dx.doi.org/10.1017/S1431927604040449
Gorelik, Tatiana; Kaiser, Ute; Kuhlmann, Thomas; Yulin, Sergey; Richter, Wolfgang
Structural characterization of ultrathin Cr and Sc films for soft X-ray mirrors. - In: Applied surface science, Bd. 230 (2004), 1/4, S. 1-7

http://dx.doi.org/10.1016/j.apsusc.2004.02.006
Chuvilin, Andrey; Kups, Thomas; Kaiser, Ute
The effect of the signal-to-noise ratio in CBED patterns on the accuracy of lattice parameter determination. - In: Journal of electron microscopy, ISSN 1477-9986, Bd. 53 (2004), 3, S. 237-244

http://dx.doi.org/10.1093/jmicro/53.3.237
Mache, Thomas; Jakob, Christine; Kutzschbach, Peter; Petzold, Thomas
Nickel-Eisen-Legierungsabscheidung mit hohen Stromdichten im ruhenden Sulfamatelektrolyten für die Mikrosystemtechnik. - In: Oberflächentage 2004, (2004), S. 318-324

Romankiewicz, Katja;
Elektrochemische Abscheidung von Chromschichten mit nanoskaligen Dispersoiden. - In: Oberflächentage 2004, (2004), S. 204-210

Mache, Thomas; Jakob, Christine; Kutzschbach, Peter; Petzold, Thomas
Nickel-Eisen-Legierungsabscheidung mit hohen Stromdichten im ruhenden Sulfamatelektrolyten für die Mikrosystemtechnik. - In: Galvanotechnik, ISSN 0016-4232, Bd. 95 (2004), 12, S. 3028-3033

Für die Herstellung von Mikroteilen wie beispielsweise Zahnrädern wird bisher nach der LIGA-Technik vorwiegend Nickel eingesetzt. Zur Erhöhung der Härte wäre die Verwendung von Legierungen vorteilhaft, die allerdings wegen der ungünstigen Geometrie und daraus folgenden starken Streuungen der Legierungszusammensetzung bisher problematisch waren. Bei Stromdichten zwischen 5 und 10 A/dm^2 und einer Temperatur von 55&ring;C lässt sich aus einem Sulfamatelektrolyten eine Nickel-Eisen-Legierung mit einem Eisenanteil von 7 % abscheiden. Durch den Legierungsanteil steigt die Härte von etwa 300 HV 0,025 für reines Nickel auf etwa 650 HV0,025 an. Durch den Zusatz von Saccharin treten lediglich geringfügige Druckspannungen in dem Bauteil auf. Allerdings treten bei dem für die Abscheidung geeigneten pH-Wert von ca. 3,5 Ausfällungen von Eisen(III)hydroxid auf, weshalb eine kontinuierliche Filtration erforderlich ist.



Sievert, Carsten; Resagk, Christian; Men, Shouqiang; Schmidt, Udo; Ziolkowski, Marek; Brauer, Hartmut
Measurement of interface deformation and magnetic field at a conducting two-fluid system. - In: Proceedings, Asia-Euro Workshop on Electromagnetic Processing of Materials, (2004), S. 41-43

Kups, Thomas; Kaiser, Ute
On the site occupancy of dopants in 4H-SiC. - In: Thüringer Werkstofftag 2004, (2004), S. 199-202

Biskupek, Johannes; Kaiser, Ute; Chuvilin, Andrey
Understanding the contrast of HRTEM-images of interstitial loops in SiC introduced by foreign ion implantation - a molecular dynamics study. - In: Thüringer Werkstofftag 2004, (2004), S. 195-197

Chuvilin, Andrey; Kups, Thomas; Kaiser, Ute
Lattice parameter measurment by CBED: accuracy limited by the noise. - In: Thüringer Werkstofftag 2004, (2004), S. 193-194

Kaiser, Ute; Chuvilin, Andrey
Z-contrast in a conventional TEM. - In: Thüringer Werkstofftag 2004, (2004), S. 191-192

Kaiser, Ute;
TEM characterization of nanostructured materials for materials science - opportunities and challenges. - In: Thüringer Werkstofftag 2004, (2004), S. 69-70

Cimalla, Volker; Kaiser, Ute; Cimalla, Irina; Ecke, Gernot; Pezoldt, Jörg; Spieß, Lothar; Ambacher, Oliver; Lu, Hai; Schaff, William
Cubic InN on r-plane sapphire. - In: Superlattices and microstructures, ISSN 1096-3677, Bd. 36 (2004), 4/6, S. 487-495

http://dx.doi.org/10.1016/j.spmi.2004.09.054
Albrecht, Arne; Botiov, Julian; Fischer, Michael; Drüe, Karl-Heinz; Hintz, Michael; Schmidt, Udo; Thust, Heiko; Wurmus, Helmut
Alternative Ansätze zur Herstellung hochstromtragfähiger Leiter in LTCC. - In: Deutsche IMAPS Konferenz, (2003), insges. 10 S.

Mache, Thomas; Kutzschbach, Peter; Jakob, Christine; Bade, Klaus
Nickelabscheidung bei Raumtemperatur mit geringen inneren Spannungen. - In: Proceedings and our portrait, (2003), insges. 10 S.

Jakob, Christine; Erler, Frank; Steinhäuser, Siegfried; Lampke, Thomas; Wielage, Bernhard
Nickeldispersionsschichten mit nanoskaligen keramischen Dispergaten in Mikrostrukturen. - In: Vorträge, (2003), S. 77-81

Steinhäuser, Siegfried; Lampke, Thomas; Wielage, Bernhard; Jakob, Christine; Erler, Frank
Zum Korrosionsverhalten von Nickel- und Kupfer-Dispersionsschichten. - In: Vorträge, (2003), S. 154-159

Mache, Thomas; Kutzschbach, Peter; Jakob, Christine; Bade, Klaus
Nickelabscheidung bei Raumtemperatur mit geringen inneren Spannungen. - In: Tagungsband zur 5. Industriefachtagung "Oberflächen- und Werkstofftechnik" und zum 6. Werkstofftechnischen Kolloquium in Chemnitz, (2003), S. 413-423

Mache, Thomas; Kutzschbach, Peter; Jakob, Christine; Bade, Klaus
Gewußt wie : Nickelabscheidung bei Raumtemperatur mit geringen Eigenspannungen. - In: Metalloberfläche, ISSN 0026-0797, Bd. 57 (2003), 11, S. 17-21

Erler, Frank; Jakob, Christine; Romanus, Henry; Spieß, Lothar; Wielage, Bernhard; Lampke, Thomas; Steinhäuser, Siegfried
Interface behaviour in nickel composite coatings with nano-particles of oxidic ceramic. - In: Electrochimica acta, ISSN 1873-3859, Bd. 48 (2003), 20/22, S. 3063-3070

Advances in micro-technology demand that new functional materials be developed so that the technical properties of micro-devices can be improved at reasonable cost. The co-deposition of nanoscaled particles during an electroplating process has been shown to bring such an improvement. This work focuses on particles of oxidic ceramics, in this case those of Al2O3 and TiO2. The diameters of the primary particles ranges from 10 to 30 nm, electrodeposited by means of a conventional Watts nickel electrolyte. A series of nickel nano-ceramic composites were produced, with co-deposition of particles as a single primary particle in the nanometre range at one end of the sale and as agglomerates up to a size of a micrometer at the other. The influence of the presence of particles on crystallisation behaviour, residual stress and texture of the deposited nickel coatings was examined by X-ray diffraction (XRD). There is a report on the interfaces between the nickel grains and the oxidic ceramic particles, investigates using transmission electron microscopy (TEM). A decreasing corrosion stability indicates an attack along the interface nickel/particles.



http://dx.doi.org/10.1016/S0013-4686(03)00380-3
Steinhäuser, Siegfried; Lampke, Thomas; Wielage, Bernhard; Jakob, Christine; Erler, Frank
Corrosion and wear behavoir of Nickel dispersion coatings with nano particles :
Zum Korrosions- und Verschleißverhalten von Nickeldispersionsschichten mit Nanopartikeln. - In: Materials science and engineering technology, ISSN 1521-4052, Bd. 34 (2003), 7, S. 633-640

http://dx.doi.org/10.1002/mawe.200390127
Fehling, Peer; Hülsenberg, Dagmar; Raab, Dagmar; Mache, Thomas; Winkler, Volker; Kern, Heinrich; Stöckel, Sabine; Weise, Kathrin; Marx, Günter
Transluzente oxidfaserverstärkte Glasmatrix-Verbundwerkstoffe. - In: Materials science and engineering technology, ISSN 1521-4052, Bd. 34 (2003), 7, S. 671-676

http://dx.doi.org/10.1002/mawe.200390134
Oberseider, Michael; Erler, Frank; Jakob, Christine; Lampke, Thomas; Steinhäuser, Siegfried; Wielage, Bernhard
Characteristics of nano-scaled Aluminium oxide- and Titanium dioxide-particles in nickel electrolytes :
Eigenschaften von nanoskaligen Aluminiumoxid- und Titandioxid-Partikeln in Nickelelektrolyten. - In: Materials science and engineering technology, ISSN 1521-4052, Bd. 34 (2003), 7, S. 627-632

http://dx.doi.org/10.1002/mawe.200390126
Fehling, Peer; Hülsenberg, Dagmar; Raab, Dagmar; Mache, Thomas; Winkler, Volker; Kern, Heinrich; Stöckel, Sabine; Weise, Kathrin; Marx, Günter
Transluzente oxidfaserverstärkte Glasmatrix-Verbundwerkstoffe. - In: 47. Internationales Wissenschaftliches Kolloquium, (2002), insges. 11 S.

Oberseider, Michael; Erler, Frank; Jakob, Christine; Lampke, Thomas; Steinhäuser, Siegfried; Wielage, Bernhard
Eigenschaften von nanoskaligen Al 2 O 3- und TiO 2-Partikeln in Metallelektrolyten. - In: 47. Internationales Wissenschaftliches Kolloquium, (2002), insges. 8 S.

Lampke, Thomas; Erler, Frank; Jakob, Christine; Lange, Karl-Heinz; Steinhäuser, Siegfried; Wielage, Bernhard
Tribologische Eigenschaften von Nickeldispersionsschichten mit Nanopatikeln. - In: 47. Internationales Wissenschaftliches Kolloquium, (2002), insges. 2 S.

Lampke, Thomas; Steinhäuser, Siegfried; Wielage, Bernhard; Jakob, Christine; Erler, Frank
Tribologische Eigenschaften von Nickeldispersionsschichten mit Nanopartikeln. - In: Vorträge, (2002), S. 15-19

Petrova, Maria; Noncheva, Z.; Jakob, Christine; Erler, Frank
Stromlos abgeschiedene Nickel-Dispersionsschichten auf Kunststoffen : Teil III: Nanoskaliger SiO2-Dispersoid. - In: Galvanotechnik, ISSN 0016-4232, Bd. 93 (2002), 2, S. 370-379

Auch bei der Metallisierung von Kunststoffen besteht die Notwendigkeit zur Erhöhung der Abriebbeständigkeit der aufgebrachten Metallschichten. Eine Möglichkeit hierzu ist der Einsatz von Dispersoiden, wobei bei dünnen Schichten die üblichen Partikelgrößen von einigen Mikrometern ausscheiden. Bei Verwendung eines alkalischen Elektrolyten mit 30 g/l Nickelsulfat, 25 g/l Natriumhypophosphit, 10 g/l Zitronensäure und 2,5 g/l SiO2 mit Teilchengrößen zwischen 30 und 60 mm lassen sich etwa 1 % SiO2 einlagern. Die Schichten zeigen einen deutlich geringeren Reibverlust bei guter Stabilität des Elektrolyten.



Schmidt, Cordt; Jakob, Christine; Schmidt, Udo
Analytik der Reaktionsprozesse : Abschlussbericht Druckhydrolyse ; Projektlaufzeit: 04/1997 - 12/2000. - Entwicklung eines Druckhydrolyseverfahrens für technische Zyanidabwässer ; Teil C
[Elektronische Ressource]. - Ilmenau. - Online-Ressource (120 S., 997 KB)Differences between the printed and electronic version of the document are possible. - Contract BMBF 02 WA 9679/5

https://edocs.tib.eu/files/e01fb02/342901591.pdf
Hülsenberg, Dagmar; Fehling, Peer; Mache, Thomas; Kern, Heinrich; Raab, Dagmar; Winkler, Volker; Marx, Günter; Weise, Kathrin; Stöckel, Sabine
Transluzente oxidfaserverstärkte Gläser. - In: Thüringer Werkstofftag, (2001), S. 17-24

Jakob, Christine;
Mikrogalvanik für die Mikrosystemtechnik. - In: Tagungsband zur 4. Industriefachtagung "Oberflächen- und Wärmebehandlungstechnik" und zum 4. Werkstofftechnischen Kolloquium in Chemnitz, (2001), S. 190-196

Steinhäuser, Siegfried; Wielage, Bernhard; Zschunke, Antje; Jakob, Christine; Erler, Frank; Nutsch, Rolf
Galvanische Verbundwerkstoffe - Nickeldispersionsschichten mit nanoskaligen Partikeln. - In: Galvanotechnik, ISSN 0016-4232, Bd. 92 (2001), 1, S. 78-84

Aus einem gängigen Watts-Nickelelektrolyten wurden Schichten mit Aluminium- bzw. Titanoxid abgeschieden. Die Durchmesser der Nanoteilchen lagen zwischen 10 und 20 nm. Durch die Zugabe von Titanoxid konnte eine Erhöhung der Härte von etwa 200 auf 300 bis 400 HVO0,025 erzielt werden. Umgekehrt gingen die Inneren Zugspannungen sowohl durch Einbau von Titan- als auch von Aluminiumoxid drastisch zurück. Erwartungsgemäß konnten bei Einbau der Nanopartikel ein besseres Verschleißverhalten festgestellt werden, wobei der lineare Verschleiß um etwa 50 % geringer ausfiel.



Hülsenberg, Dagmar; Fehling, Peer; Mache, Thomas; Winkler, Volker; Raab, Dagmar; Boccaccini, Aldo R.
Herstellung und Charakterisierung neuer faserverstärkter Glasmatrix-Verbundwerkstoffe. - In: Verbundwerkstoffe und Werkstoffverbunde, (2001), S. 365-369

Jakob, Christine; Erler, Frank; Nutsch, Rolf; Steinhäuser, Siegfried; Wielage, Bernhard; Zschunke, Antje
Electroplated nickel-ceramic composite coatings with nanoscaled particles for microtechnology. - In: INTERFINISH 2000, (2000), S. 394-404

Schmidt, Udo; Vollrath, U.; Schmidt, C.; Müller, H.; Spielmann, W.
Analysis of the process and the chemistry in pressure hydrolysis of heavy-metal-cyanide complexes and of the reactions of the associated organic substances. - In: INTERFINISH 2000, (2000), S. 559-575

Schwanbeck, Heike; Schmidt, Cordt;
Galvanik-Verbundwerkstoffe : Metallkeramiken und -gläser galvanisch herstellen. - In: Metalloberfläche, ISSN 0026-0797, Bd. 54 (2000), 7, S. 22-23

Jakob, Christine; Erler, Frank; Nutsch, Rolf; Steinhäuser, Siegfried; Wielage, Bernhard; Zschunke, Antje
Nickeldispersionsabscheidung mit nanoskaligen Partikeln : Entwicklungsstand und experimentelle Ergebnisse. - In: Metalloberfläche, ISSN 0026-0797, Bd. 54 (2000), 9, S. 50,52-57, insges. 7 S.

Petrova, Maria; Noncheva, Z. B.; Petrov, C.; Schmidt, Cordt
Stromlos abgeschiedene Nickel-Dispersionsschichten auf Kunststoffen : Teil II: Nanoskalige Dispersoide. - In: Galvanotechnik, ISSN 0016-4232, Bd. 91 (2000), 12, S. 3378-3384

Durch die Abscheidung von Metallschichten auf Kunststoffen lassen sich die Eigenschaften der Polymere dramatisch verändern. Diese Eigenschaften können bei Anwendung von Dispersionsschichten weiter verbessert werden. Durch den Einbau von 2,5 % nanoskaligem Titanoxid in Nickel/Phosphor-Schichten erhöht sich der Reibungskoeffizient gegenüber feststofffreiem Nickel/Phosphor um den Faktor sieben. Optimale Ergebnisse werden mit einem Elektrolyten mit 40 g/l Nickelsulfat, 25 g/l Natriumhypophosphit, 15 g/l Zitronensäure und 2,5g/l Titanoxid erzielt.



Petrova, Maria; Petrov, C.; Schmidt, Cordt;
Stromlos abgeschiedene Nickel-Dispersionsschichten auf Kunststoffen : Teil I: Mikroskalige Dispersoide. - In: Galvanotechnik, ISSN 0016-4232, Bd. 91 (2000), 5, S. 1262-1270

Durch die Einlagerung von Teilchen in Metallschichten lassen sich die Eigenschaften deutlich und problembezogen variieren. So verbessert beispielsweise die Einlagerung von PTFE die Gleiteigenschaften, und die Mitabscheidung von Siliziumcarbid erhöht die Verschleißbeständigkeit. Für die Abscheidung auf Kunststoffen wurde ein Elektrolyt aus Nickelsulfat, Natriumhypophosphit und Zitronensäure herangezogen, dem Siliziumcarbid in Mengen zwischen 10 und 40 g/l zugesetzt wurde. Der Anteil an Siliziumcarbid wurde mittels EDX bestimmt. Für die abgeschiedenen Schichten bis 10 æm erwiesen sich die Siliziumteilchen mit 1 bis 5 æm als zu groß, um nennenswerte Mengen abscheiden zu können. Bessere Ergebnisse sollten mit nanoskaligen Partikeln zu erzielen sein.



Schwanbeck, Heike;
Preparation and characterisation of magnetic nanostructures using filtration membranes. - In: Electrochimica acta, ISSN 1873-3859, Bd. 45 (2000), 27, S. 4389-4398

http://dx.doi.org/10.1016/S0013-4686(00)00502-8
Liebscher, Heinz;
Some practical aspects of the electrodeposition of iron group metal alloys. - In: Zeitschrift für physikalische Chemie, ISSN 2196-7156, Bd. 208 (1999), S. 183-194

http://dx.doi.org/10.1524/zpch.1999.208.Part_1_2.183
Winterstein, Volker; Schwanbeck, Heike; Müller, Klaus; Schmidt, Udo
Galvanisch abgeschiedene, hartmagnetische Kobalt-Legierungsschichten für Weg- und Winkelmeßsysteme. - In: Vorträge und Poster, (1999), S. 83-88

Erler, Frank; Kutzschbach, Peter; Jakob, Christine; Schmidt, Cordt
Untersuchungen zur elektrolytischen Nickeldispersionsabscheidung mit nanoskaligen Dispergaten. - In: 44. Internationales Wissenschaftliches Kolloquium, (1999), insges. 7 S.

Schmidt, Cordt; Kutzschbach, Peter; Kutzschbach, Peter *1944-*; Erler, Frank
Eine neue Dimension : Nanoskalige Partikel in galvanisch abgeschiedenen Nickelschichten. - In: Metalloberfläche, ISSN 0026-0797, Bd. 53 (1999), 6, S. 32-34, 37-39, insges. 6 S.

Tomov, Ivan; Karagodin, Pawel; Erler, Frank; Schmidt, Cordt
Eisenschichten elektrolytisch abgeschieden : Ermitteln der Mengenanteile von Texturkomponenten. - In: Metalloberfläche, ISSN 0026-0797, Bd. 53 (1999), 11, S. 48-50, 52-53, insges. 5 S.

Jakob, Christine; Nutsch, Rolf; Halbedel, Bernd
Galvanische Beschichtung von poröser Sinterkeramik. - In: Galvanotechnik, ISSN 0016-4232, Bd. 90 (1999), 10, S. 2696-2700

Zur Erhöhung der Zähigkeit von keramischen Mahlkörpern aus Bariumhexaferrit mit einem Durchmesser von 1 bis 1,6 mm werden diese mit etwa 30 æm Nickel beschichtet. Die Beschichtung erfolgt nach Vorbehandlung und Aktivierung zunächst chemisch zur Erzeugung einer Startschicht und anschließende galvanische Verstärkung in einer Vibrationstrommel. Die Schicht erhöht die Standzeit der Mahlkörper und vermindert weitgehend eine Verunreinigung des Mahlgutes durch Abrieb.



Hofmann, Thomas;
Untersuchungen zum Einfluß von Pulse-Plating auf die Abscheidung von Kupfer aus Leiterplattenelektrolyten, 1999. - 175 Bl. Ilmenau : Techn. Univ., Diss., 1999

Kutchoukov, V.; Philippov, Philipp; Schmidt, Cordt
Electroplating of copper in microstructured silicon wafers. - In: Micro system technologies 98, (1998), S. 737-739

Winterstein, Volker; Müller, Klaus; Schwanbeck, Heike; Schmidt, Udo
Magnetische Eigenschaften von Kobalt-Legierungsschichten auf Cu-, Ms-, Al- und Fe-Trägern für den Einsatz in der Längen- und Winkelmeßtechnik. - In: 43. Internationales Wissenschaftliches Kolloquium, (1998), insges. 6 S.

Hofmann, Thomas; Schmidt, Cordt;
Untersuchung zum Einfluß von Pulse-Plating auf die elektrolytische Abscheidung von Kupfer. - In: 43. Internationales Wissenschaftliches Kolloquium, (1998), insges. 6 S.

Schwanbeck, Heike; Schmidt, Udo; Winterstein, Volker; Müller, Klaus
Galvanische Abscheidung von Cobalt-Legierungsschichten für magnetische Längen- und Winkelmeßsysteme. - In: 43. Internationales Wissenschaftliches Kolloquium, (1998), insges. 6 S.

Schmidt, Cordt; Karagodin, Pawel; Erler, Frank; Mache, Thomas
Betrachtungen über Wechselbeziehungen zwischen Morphologie der Oberfläche, Gefüge und Textur von elektrolytisch abgeschiedenen Metallschichten. - In: 43. Internationales Wissenschaftliches Kolloquium, (1998), insges. 6 S.

Winkler, Marion; Kutzschbach, Peter; Zeidler, Hubert
Galvanotechnik für den Titanguß?. - In: Metalloberfläche, ISSN 0026-0797, Bd. 52 (1998), 3, S. 190-192

Schmidt, Cordt; Karagodin, Pawel; Tomov, Ivan; Erler, Frank; Mache, Thomas
Electrolytically deposited steel coatings. Morphology of the surface, structure, texture and characteristics :
Elektrolytische Eisenschichten : Morphologie der Oberfläche, Gefüge, Textur und Eigenschaften. - In: Metalloberfläche, ISSN 0026-0797, Bd. 52 (1998), 12, S. 968-974

Winkler, Marion;
Untersuchungen zur elektrochemischen Abscheidung von Zwischenschichten für den Feinguß von Titan. - In: Kurzfassungen der Vorträge, (1997), S. 67-69

Liebscher, Heinz; Kutzschbach, Peter
Praxisnahe Methoden zur Charakterisierung der hydrodynamischen Bedingungen an Elektroden in Strömungszellen. - In: Kurzfassungen der Vorträge, (1997), S. 108-111

Schmidt, Cordt; Mache, Thomas
Characterization of copper layers :
Charakterisierung von Kupferschichten : Qualitätsbewertung galvanisch abgeschiedener Metallschichten mit Hilfe der Rasterkraftmikroskopie. - In: Metalloberfläche, ISSN 0026-0797, Bd. 50 (1996), 9, S. 698-703

Ehrling, Christiane; Schmidt, Udo; Liebscher, Heinz
Analysis of chromium(III)-fluoride-complexes by ion chromatography. - In: Fresenius' journal of analytical chemistry, ISSN 1432-1130, Bd. 354 (1996), 7, S. 870-873

http://dx.doi.org/10.1007/s0021663540870
Hülsenberg, Dagmar; Harnisch, Alf; Jakob, Christine; May, Markus; Straube, Berit
High aspect ratio structures obtained by electroforming in microstructured glass. - In: Microsystem technologies, ISSN 1432-1858, Bd. 2 (1996), 3, S. 109-113

http://dx.doi.org/10.1007/s005420050025
Becher, Ulf; Schmidt, Cordt; Ehrfeld, Wolfgang; Löwe, Holger
Galvanische Abscheidung von Nickel-Phosphor-Legierungen in Mikrostrukturen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 86 (1995), 10, S. 3180-3186

Liebscher, Heinz;
Anwendungsmöglichkeiten und Probleme der galvanischen Abscheidung von Eisen und Eisenlegierungen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 86 (1995), 7, S. 2130-2136

Liebscher, Heinz; Kutzschbach, Peter
Möglichkeiten und Grenzen der Kombination von Metallabscheidung und -auflösung in Kreislaufsystemen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 86 (1995), 4, S. 1096-1102

Schwanbeck, Heike; Liebscher, Heinz;
Neue Werkstoffe durch galvanotechnische Verfahren - Mikroverbundwerkstoffe. - In: Elektrochemie und Werkstoffe, (1995), S. 455-466

Pilz, Uwe;
Numerische Simulationen des elektrischen Strömungsfeldes und des Stofftransports bei der elektrochemischen Metallabscheidung. - Espoo : VTT, Techn. Forschungszentrum. - 141 S.. - (VTT publications ; 247) : Zugl.: Ilmenau, Techn. Univ., Habil.-Schr., 1995
ISBN 951-38-4785-3
Literaturangaben

Liebscher, Heinz; Rempt, Wolfgang; Kutzschbach, Peter
Probleme der Anwendung hoher Stromdichten beim Draht- und Bandgalvanisieren. - In: Galvanotechnik, ISSN 0016-4232, Bd. 85 (1994), 9, S. 2878-2884

Liebscher, Heinz; Kutzschbach, Peter
Möglichkeiten und Grenzen der Kombination von Metallabscheidung und -auflösung in Kreislaufsystemen. - In: Umweltgerechte Galvano- und Oberflächentechnik, (1994), S. 106-112

Schmidt, Kristina; Hülsenberg, Dagmar; Eckstein, Manuela; Harnisch, Alf; Jakob, Christine; Nutsch, Rolf
Mikrostrukturierung von Glas. - In: F & M, ISSN 1437-9503, Bd. 102 (1994), 1/2, S. 21-24

Pilz, Uwe; Liebscher, Heinz
Mikrostrukturen: Betrachtungen zum Stofftransport. - In: Metalloberfläche, ISSN 0026-0797, Bd. 47 (1993), 7, S. 327-330

Thommes, A.; Stark, W.; Bacher, W.; Jakob, Christine; Nutsch, Rolf; Liebscher, Heinz
Untersuchungen zur Galvanoumformung von Mikrostrukturen aus weichmagnetischen Fe-Ni-Legierungen. - In: Oberflächentechnik '93, (1993), S. 20-23

Hoch, H.; Raub, Christoph; Rauscher, Gerhard; Reeßing, Friedrich; Liebscher, Heinz
Magnetische Speichermedien auf der Basis anodischer Aluminiumoxidschichten. - In: Oberflächenbehandlung von Aluminium und anderen Leichtmetallen, (1993), S. 75-86

Degner, W.; Hecht, G.; Nutsch, Rolf
Galvanisch abgeschiedene Legierungsschichten aus unedlen Metallen als Werkstoff für Schwachstromkontakte : Teil 4: Nickellegierungen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 84 (1993), 3, S. 776-786

Nutsch, Rolf; Liebscher, Heinz; Degner, W.; Hecht, G.
Galvanisch abgeschiedene Legierungsschichten aus unedlen Metallen als Werkstoff für Schwachstromkontakte : Teil 3: Silberlegierungen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 84 (1993), 2, S. 425-433

Becher, Ulf;
Elektrolytische Abscheidung von Ni-P-Legierungen zur Herstellung von Mikrostrukturen nach dem LIGA-Verfahren. - In: Mikrosysteme für Verfahrens- und Fertigungstechnik, (1993), S. 233-236

Liebscher, Heinz;
Das Adsorptions-Diffusionsmodell der Einebnung im Zusammenhang mit der Abscheidung in Mikrostrukturen. - In: Oberflächentechnik '92, (1992), S. 85-88

Liebscher, Heinz
Untersuchungen über die elektrolytische Kobaltabscheidung in anodischen Aluminiumoxidschichten als Grundlage magnetischer Speichersysteme : Abschlußbericht zum AIF-Forschungsprojekt 74D ; April 1991 - Dezember 1992. - Ilmenau [u.a.]. - Online-Ressource (226 S., 10,7 MB)Unterschiede zwischen dem gedruckten Dokument und der elektronischen Ressource können nicht ausgeschlossen werden. - Auch als gedr. Ausg. vorhanden

https://edocs.tib.eu/files/e01fn09/611332477.pdf
Nutsch, Rolf; Liebscher, Heinz
Galvanische Abscheidung von Silber-, Zinn- und Nickellegierungen für Steckverbinderkontakte. - In: Galvanotechnik, ISSN 0016-4232, Bd. 83 (1992), 8, S. 2586-2588

Andrä, Karsten; Becher, Ulf; Schmidt, Cordt;
Die Überwachung der Wirksamkeit organischer Zusätze in Leiterplattenelektrolyten mittels potentiostatischer Einschaltbelastungen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 83 (1992), 8, S. 2763-2771

Hecht, G.; Degner, W.; Nutsch, Rolf
Galvanisch abgeschiedene Legierungsschichten aus unedlen Metallen als Werkstoff für Schwachstromkontakte : Teil 2: Zinnlegierungen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 83 (1992), 3, S. 4094-4103

Liebscher, Heinz; Kutzschbach, Peter; Rempt, Wolfgang
Probleme der Metallabscheidung in Kreislaufsystemen. - In: Galvanotechnik, ISSN 0016-4232, Bd. 82 (1991), 9, S. 3035-3042
Richtiger Name des 2. Verfassers: Peter Kutzschbach

Rempt, Wolfgang; Kutzschbach, Peter; Liebscher, Heinz
Galvanische Metallabscheidung bei Verwendung depolarisierter inerter Anoden. - In: Fortschritt durch Oberflächentechnik, (1991), S. 33-36

Liebscher, Heinz; Kutzschbach, Peter; Rempt, Wolfgang
Probleme der Metallabscheidung in Kreislaufsystemen. - In: Oberflächentechnologie im Europa der 90er Jahre, (1991), S. 30-37

Nutsch, Rolf; Liebscher, Heinz
Galvanische Abscheidung von Silber-, Zinn- und Nickellegierungen für Steckverbinderkontakte. - In: Oberflächentechnik und Tribologie, (1991), S. 132-134

Rempt, Wolfgang; Baum, K.-D.; Liebscher, Heinz
Untersuchungen zur Hochgeschwindigkeitsabscheidung beim Drahtgalvanisieren. - In: Galvanotechnik, ISSN 0016-4232, Bd. 82 (1991), 4, S. 1197-1202

Schmidt, Cordt;
Struktur und Eigenschaften von Kupferschichten bei der Abscheidung mit hohen Stromdichten. - In: Galvanotechnik, ISSN 0016-4232, Bd. 82 (1991), 11, S. 3800-3818

Pilz, Uwe;
Die mikrorechnergestützte Berechnung der Stromdichteverteilung elektrochemischer Anordnungen mittels der Finite-Element-Methode, 1991. - Getr. Zählung Ilmenau : Techn. Hochsch., Diss., 1991
Enth. außerdem: Thesen

Müller, Klaus; Winterstein, Volker; Müller, Wolfgang; Schmidt, Udo; Weinmeister, Andreas
Zum magnetischen Verhalten galvanisch abgeschiedener senkrechtanisotroper CoNi-Speicherschichten. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 36 (1990), 3, S. 123-142

Zielonka, Andreas;
Untersuchung einer Methode zur Prozesskontrolle und Erprobung an Elektrolyten zur Abscheidung von Zinn-Blei-Legierungsschichten, 1988. - 100 Bl. Ilmenau : Techn. Hochsch., Diss., 1988
Enth. außerdem: Thesen

Rempt, Wolfgang;
25 Jahre Arbeitsausschuß "Galvanotechnik"
Sonderausg.. - Suhl, 1987. - 46 S.
Zielonka, Andreas; Pilz, Uwe; Krümmling, Franz; Liebscher, Heinz
Elektrolytische Abscheidung von Zinn-Blei-Legierungen auf Drähten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 31 (1986), 2, S. 209-211

Schmidt, Cordt;
Zwillingsbildung bei der Kupferabscheidung mit hohen Stromdichten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 31 (1986), 2, S. 175-178

Liebscher, Heinz;
Probleme der Stromdichteverteilung an nichtebenen Oberflächen. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 31 (1986), 2, S. 141-144

Haag, Uwe;
Entwicklung und Realisierung einer mikrorechnergesteuerten Belastungs- und Messwerterfassungsanlage für elektrochemische Zellen, 1986. - 101 Bl. : Ilmenau, Techn. Hochsch., Diss., 1986
Enth. außerdem: Thesen

Liebscher, Heinz; Schilling, Manfred; Kruglikov, S. S.; Jarlykov, M. M.; Starkova, N. N.
Teoretičeskij rasčet vtoričnogo raspredelenija toka na periodičeskich dvumernych mikroprofiljach. - In: &ptbov;Elektrochimija, ISSN 0424-8570, Bd. 21 (1985), 9, S. 1245-1247

Schmidt, Cordt;
Elektrochemische Metallbeschichtung. - In: Fertigungsverfahren in der Gerätetechnik, (1985), S. 365-383

Schmidt, Cordt;
Oberflächenvorbehandlung. - In: Fertigungsverfahren in der Gerätetechnik, (1985), S. 362-365

Schmidt, Cordt;
Aufgaben und Bedeutung der Beschichtungstechnik. - In: Fertigungsverfahren in der Gerätetechnik, (1985), S. 362

Jakob, Christine; Liebscher, Heinz
Modelluntersuchungen zum Einfluß der hydrodynamischen Bedingungen auf den galvanotechnischen Abscheidungsprozeß. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 31 (1985), 4, S. 137-146

Wachsmuth, Elmar;
Untersuchungen zur elektrochemischen Abscheidung von Eisen-Chrom-Legierungsschichten aus Fluoroboratelektrolyten. - Ilmenau, 1985. - 1 Band (verschiedene Seitenzählungen)
Technische Hochschule Ilmenau, Dissertation 1985

Enthält Thesen

Vieweger, Ulrich;
Untersuchung des Einflusses von organischen Zusätzen auf die Kupferabscheidung bei hohen Stromdichten, 1985. - 99 Bl. Ilmenau : Techn. Hochsch., Diss., 1985

Liebscher, Heinz;
Svojstva &ptbov;elektrolitičeski osaždennych metalličeskich pokrytij. - In: Povyšenie kačestva poverchnosti i plakirovanie metallov, (1984), Razd. 3.3., Seite 102-106

Liebscher, Heinz;
Technologičeskie aspekty. - In: Povyšenie kačestva poverchnosti i plakirovanie metallov, (1984), Razd. 3.2., Seite 77-102

Liebscher, Heinz;
Teoretičeskie osnovy. - In: Povyšenie kačestva poverchnosti i plakirovanie metallov, (1984), Razd. 3.1., Seite 60-77

Liebscher, Heinz;
Calculation of the current distribution at wave-like electrodes with polarization. - In: Journal of electroanalytical chemistry, ISSN 1873-2569, Bd. 180 (1984), 1/2, S. 445-451

http://dx.doi.org/10.1016/0368-1874(84)83600-X
Schmidt, Cordt;
Zusammenhänge zwischen Oberflächenqualität und Struktur elektrolytisch abgeschiedener Kupferschichten. - In: Vorträge der XXI. Galvanotechnischen Fachtagung vom 2. bis 4. Mai 1984 in Suhl/DDR, (1984), S. 27-32

Müller, Wolfgang; Liebscher, Heinz;
Die Herstellung magnetischer Speicherschichten - ein modernes galvanotechnisches Verfahren. - In: Vorträge der XXI. Galvanotechnischen Fachtagung vom 2. bis 4. Mai 1984 in Suhl/DDR, (1984), S. 20-26

Liebscher, Heinz;
Eigenschaften elektrolytisch abgeschiedener Metallschichten. - In: Oberflächenveredeln und Plattieren von Metallen, (1983), Abschnitt 3.3., Seite 107-114

Liebscher, Heinz;
Technologische Aspekte. - In: Oberflächenveredeln und Plattieren von Metallen, (1983), Abschnitt 3.2., Seite 82-107

Liebscher, Heinz;
Grundlagen. - In: Oberflächenveredeln und Plattieren von Metallen, (1983), Abschnitt 3.1., Seite 62-82

Liebscher, Heinz;
Zum Problem geschlossener Kreisläufe bei galvanotechnischen Verfahren. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 28 (1983), 2, S. 193-196

Burkhardt, Werner; Liebscher, Heinz;
Galvanotechnische Metallabscheidungsverfahren. - In: Elektrotechnologie, (1983), S. 253-296

Aßmann, Kurt; Engmann, Bernhard; Liebscher, Heinz
Beitrag zur mathematischen Modellierung von Verfahren in der Galvanotechnik. - In: Elektrie, ISSN 0013-5399, Bd. 36 (1982), 2, S. 79-82

Liebscher, Heinz; Nutsch, Rolf; Proft, Rudolf; Thiele, Wolfgang
Technische Anwendung der Elektrochemie. - In: Systeme der Elektroenergietechnik, (1982), S. 778-903
Abschn. 5.2.1; 5.2.4.1-5.2.4.2; 5.2.5.1-5.2.5.3 von H. Liebscher. - Abschn. 5.2.2 von R. Nutsch

Trandafilov, A.; Petrov, Ch.; Liebscher, Heinz
Untersuchungen zum Stoffübergang bei der elektrolytischen Abscheidung von Kobalt in Silikofluoridelektrolyten. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 28 (1982), 1, S. 103-111

Schilling, Martin; Beyer, Rainer; Liebscher, Heinz
Allgemeine Betrachtungen zur Stromdichteverteilung an wellenförmigen Oberflächen. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 28 (1982), 1, S. 95-101

Nutsch, Rolf;
Elektrochemie. - In: Elektrotechnik, Elektronik, (1981), S. 266-286

Müller, Wolfgang;
Experimentalversuche zur Vorlesung Elektrochemie im Rahmen des Fachstudiums der Sektion Elektrotechnik der Technischen Hochschule Ilmenau. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 27 (1981), 3, S. 133-157

Jakob, Bernd;
Untersuchungen zur Kennwertermittlung und Glanzbildung bei der Kupferabscheidung aus Sulfatelektrolyten, 1981. - 148 Bl. : Ilmenau, Techn. Hochsch., Diss., 1981

Schmidt, Cordt;
Elektrochemische Metallbeschichtung. - In: Fertigungsverfahren in der Gerätetechnik, (1980), S. 375-401

Schmidt, Cordt;
Oberflächenvorbehandlung. - In: Fertigungsverfahren in der Gerätetechnik, (1980), S. 372-375

Schmidt, Cordt;
Aufgaben und Bedeutung der Beschichtungstechnik. - In: Fertigungsverfahren in der Gerätetechnik, (1980), S. 372

Liebscher, Heinz;
Eigenschaften elektrolytisch abgeschiedener Metallschichten. - In: Oberflächenveredeln und Plattieren von Metallen, (1979), Abschnitt 3.3., Seite 107-114

Liebscher, Heinz;
Technologische Aspekte. - In: Oberflächenveredeln und Plattieren von Metallen, (1979), Abschnitt 3.2., Seite 82-107

Liebscher, Heinz;
Grundlagen. - In: Oberflächenveredeln und Plattieren von Metallen, (1979), Abschnitt 3.1., Seite 62-82

Rempt, Wolfgang;
Untersuchungen zur Beeinflussung der elektrolytischen Metallabscheidung durch die Welligkeit des Stromes. - In: Vorträge der XVI. Galvanotechnischen Fachtagung Oberhof 1979 am 22. und 23. Oktober 1979, (1979), S. 71-77

Schmidt, Cordt;
Zur elektrischen Leitfähigkeit elektrochemisch abgeschiedener Kupferschichten. - In: Vorträge der XVI. Galvanotechnischen Fachtagung Oberhof 1979 am 22. und 23. Oktober 1979, (1979), S. 5-9

Eisermann, Peter; Liebscher, Heinz
Untersuchungen zur elektrolytischen Abscheidung von glänzenden Kupferschichten aus Sulfatelektrolyten unter nichtstationären Bedingungen. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 25 (1979), 5, S. 7-24

Jakob, Christine;
Modelluntersuchungen zum Einfluß der hydrodynamischen Bedingungen auf den galvanotechnischen Abscheidungsprozeß, 1979. - Getr. Zählung : Ilmenau, Techn. Hochsch., Diss., 1979

Rempt, Wolfgang;
Untersuchungen zur Anwendung thyristorgesteuerter Gleichrichter bei der elektrolytischen Abscheidung von Metallen, 1979. - getr. Zählung : Ilmenau, Techn. Hochsch., Diss., 1979

Erck, Alfred; Knappe, Joachim; Liebscher, Heinz; Mühe, Hansgeorg; Schädlich, Christian
Einige Arbeitsstandpunkte, das Wesen und die Funktion der bürgerlichen Wissenschaftstheorie, Technikphilosophie und Kunsttheorie in der Gegenwart betreffend. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 24 (1978), 3, S. 3-24

Kutzschbach, Peter; Schmidt, Cordt;
Untersuchungen zum elektrolytischen Polieren von Stahl in zusatzfreien Eisenfluoboratelektrolyten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 22 (1977), 2, S. 153-156

Müller, Wolfgang; Liebscher, Heinz; Liebscher, Heinz *1931-2021*; Wachsmuth, Elmar;
Die elektrolytische Abscheidung von Eisen aus Fluoboratelektrolyten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 22 (1977), 2, S. 127-132

Ludwig, M.; Liebscher, Heinz
Untersuchung zur Abscheidung von Metallen mit Hilfe von Impulsströmen. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 22 (1977), 2, S. 117-120

Petrow, Chr.; Trandafilow, A.; Liebscher, Heinz
Kathodische Trennfaktoren von Fremdmetallen bei der Kobaltabscheidung aus Silikofluoridelektrolyten. - In: Metalloberfläche, ISSN 0026-0797, Bd. 30 (1976), 9, S. 419-422

Petrow, Chr.; Trandafilow, A.; Liebscher, Heinz
Indikatormethode zur Untersuchung der Stoffübergangsgeschwindigkeit von Diffusionsvorgängen während der elektrolytischen Abscheidung von Metallen. - In: Metalloberfläche, ISSN 0026-0797, Bd. 30 (1976), 8, S. 373-375

Ludwig, Maria;
Untersuchungen zur elektrolytischen Abscheidung von Metallen mit Impulsströmen, 1976. - 92 Bl. : Ilmenau, Techn. Hochsch., Diss., 1976

Kutzschbach, Peter;
Untersuchungen zum elektrolytischen Polieren von Stahldrähten in zusatzfreien Eisenfluoroboratlösungen, 1976. - 128 Bl. : Ilmenau, Techn. Hochsch., Diss., 1976

Unruh, Jürgen N. M.;
Untersuchungen zur Anwendung hoher Stromdichten bei der elektrolytischen Metallabscheidung, 1975. - 214 Bl. : Ilmenau, Techn. Hochsch., Diss., 1975

Schmidt, Cordt; Kutzschbach, Peter; Kutzschbach, Peter *1944-*; Liebscher, Heinz;
Elektrochemisches Polieren zur Vorbehandlung von Metalloberflächen. - In: Vorträge der XI. Galvanotechnischen Fachtagung Suhl 1973 vom 26. - 27. April 1973, (1973), S. 72-81

Liebscher, Heinz;
Probleme der Darstellung von Reinstmetallen mit elektrolytischen Verfahren. - In: Reinststoffe in Wissenschaft und Technik, (1972), S. 728-747

Hannemann, Monika; Liebscher, Heinz
Untersuchungen zum Mechanismus der Glanzbildung bei der Abscheidung von Kupferüberzügen aus dem Sulfatelektrolyten unter Verwendung verschiedener Zusätze. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 18 (1972), 4, S. 109-115

Meyer, Manfred; Müller, Wolfgang; Müller, Wolfgang *1935-2019*; Liebscher, Heinz;
Untersuchungen zum Fremdstoffeinbau bei der Abscheidung von Kupfer aus cyanidischen Elektrolyten. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 18 (1972), 4, S. 103-108

Fink, Heinz; Fliegner, Herwig; Liebscher, Heinz
Einflußgrößen bei der elektrolytischen Abscheidung von Eisen aus Chloridelektrolyten. - In: Wissenschaftliche Zeitschrift / Technische Hochschule Ilmenau, ISSN 0043-6917, Bd. 18 (1972), 4, S. 91-101

Liebscher, Heinz; Haugk, Peter; Unruh, Jürgen
Untersuchungen zur elektrolytischen Abscheidung von Metallen mit hohen Stromdichten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 16.1971, Teil 1, S. 360

Hannemann, Monika; Liebscher, Heinz
Elektrochemische Untersuchungen an Glanzkupferelektrolyten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 16.1971, Teil 1, S. 359-360

Schmidt, Cordt; Löwer, Horst; Peger, Frank; Oi, Ho; Hannemann, Monika; Liebscher, Heinz
Untersuchungen der Eigenspannungen bei elektrolytisch abgeschiedenen Kupferschichten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 13 (1968), 4, S. 35-42

Oppermann, Heinrich; Mummert, Kurt; Liebscher, Heinz;
Beitrag zur Elektrokristallisation von Eisen. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 13 (1968), 4, S. 15-20

Müller, Wolfgang;
Die galvanische Abscheidung und die physikalischen Eigenschaften von Kobaltschichten aus dem Sulfamatelektrolyten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 11 (1966), 4, S. 49-57

Liebscher, Heinz; Mummert, Kurt
Untersuchungen zur Mitabscheidung von Fremdmetallen in geringen Konzentrationen. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 11 (1966), 4, S. 31-38

Krümmling, Franz;
Über die Erhöhung des Korrosionsschutzwertes galvanischer Glanznickelschichten. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 9.1964, Teil A, S. 67-72

Schmidt, Cordt;
Über den Einfluß der Grundmetalltextur auf die inneren Spannungen 1. Art von elektrolytisch abgeschiedenen Nickelüberzügen. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 9.1964, Teil A, S. 59-65

Hampel, Josef; Theile, Hans
Über die Abscheidung von Zink aus einem Pyrophosphatelektrolyten unter dem Einfluß verschiedener Inhibitoren. - In: Internationales wissenschaftliches Kolloquium / Technische Hochschule Ilmenau, ISSN 0374-3365, Bd. 9.1964, Teil A, S. 55-58

Burkhardt, Werner;
Über den Einfluß von Werkstück und Galvanisiergestell auf die Metallverteilung galvanischer Schutzüberzüge. - Ilmenau, 1964. - 44, 36 Blätter
Hochschule für Elektrotechnik, Dissertation 1964


Hampel, Josef; Stumpf, G.; Zeng, H.
Untersuchungen über die Abscheidung von Kupfer und Nickel aus dem Pyrophosphatelektrolyten. - In: Elektrie, ISSN 0013-5399, Bd. 17 (1963), 8, S. 269-270

Krümmling, Franz;
Über die Abscheidung von Nickel-Doppelschichten. - In: Wissenschaftliche Zeitschrift der Hochschule für Elektrotechnik, Ilmenau, Bd. 8 (1962), 4, S. 337-339

Burkhardt, Werner;
Über den Einfluß von Werkstück und Galvanisiergestell auf die Metallverteilung galvanischer Schutzüberzüge. - In: Internationales Kolloquium an der Hochschule für Elektrotechnik Ilmenau, Bd. 5.1960, Teil C, S. 43-52

Hampel, Josef;
Untersuchungen über die Abscheidung des Cadmiums aus dem Sulfamatelektrolyten. - In: Internationales Kolloquium an der Hochschule für Elektrotechnik Ilmenau, Bd. 5.1960, Teil C, S. 39-42

Burkhardt, Werner;
Automatisierung in der galvanotechnischen Massenproduktion. - In: Wissenschaftliche Zeitschrift der Hochschule für Elektrotechnik, Ilmenau, Bd. 5 (1959), 1, S. 15-26

Hampel, Josef; Theile, Hans
Die Abscheidung des Kadmiums aus Äthylendiaminelektrolyten. - In: Internationales Kolloquium an der Hochschule für Elektrotechnik Ilmenau, Bd. 3 (1958), S. 81

Burkhardt, Werner;
Automatisierung in der galvanotechnischen Massenproduktion. - In: Internationales Kolloquium an der Hochschule für Elektrotechnik Ilmenau, Bd. 3 (1958), S. 69-80

Hampel, Josef;
Die Platinmetalle in der Galvanotechnik. - In: Wissenschaftliche Zeitschrift der Hochschule für Elektrotechnik, Ilmenau, Bd. 3 (1957), 3/4, S. 223-231