Publikationen

Magnetorheological (MR) dampers have a virtue over conventional dampers, where their damping properties can be adjusted using a magnetic field. However, MR dampers have been barely implemented in small vibratory systems, in which the modal mass and stiffness are relatively small. This is due to two major reasons, namely its high parasitic damping force and big moving mass. When such an MR damper is installed in a small vibratory system, the system‘s default damping ratio is increased and therefore its dynamic is reduced. Here, a new concept of an MR damper utilizing the porous medium and shear operating mode together with an external non-moving electromagnet is proposed. This combination results in an MR damper with a low parasitic damping force and a small moving mass. For comparison purposes, a benchmark MR damper with comparable geometry is constructed. The proposed MR damper possesses a passive friction force that is 8× smaller and OFF-state passive viscous damping that is 10-20× smaller than the benchmark MR damper. An investigation of the proposed MR damper performance in a test vibratory system shows almost no reduction of the system dynamic. Therefore, this proposed MR damper configuration can be suitable for applications in small vibratory systems.

Ongoing developments in nanotechnology demand higher spatial resolution and thus, higher amplitude sensitivity in Atomic Force Microscopy (AFM). In this work, active cantilevers with integrated sensor and actuator systems are parametrically excited using a novel, analog feedback circuit. With that it is possible to adapt the strength and sign of a cubic nonlinearity which provides a bound to the amplitudes in resonance operation. The system response shows steeper resonance curves and therefore higher amplitude sensitivities compared to forced excited cantilevers. Theoretical findings are validated experimentally.

Magnetorheological fluid (MR) based dampers have been established as an alternative to classical hydraulic dampers with proportional electromagnetic valves under vibration processes which demand adaptive damping forces. Almost all MR-dampers are spatially 1-Degree-of-Freedom (DOF) dampers, having only one axis or direction of damping force generation. In many technical applications there exist movements in more than one spatial DOF, eventually necessitating more than one damper. Because of this, the damping is required not only in one but in more spatial directions, yet adjustable. In this work, a new design of a spatial 3DOF MR damper is proposed to allow damping in three directions within one damping device. The underlying motivation is to spatially integrate three damping directions in one device to potentially reduce installation space compared to three separate 1 DOF dampers. The basic idea of the construction is to use one fluid chamber with several spatially distributed control elements at different positions of the fluid chamber. The control elements are electromagnets, generating the magnetic field in the fluid at different positions so that in total 3 spatial DOFs can be damped individually. Experiments and investigation are made, where the damper's behavior are analyzed not only in one single DOF but also in more than one DOF. It is shown, that the damping concept can generate damping in all three spatial DOFs, both individually or together. Moreover, the damping can be generated to be dominant in one specific direction, meanwhile minimum in the other direction orthogonal to it.

A hybrid damper concept is presented here using a combination of a Magnetorheological (MR) Fluid (MRF) and Shape Memory Alloy (SMA)-based energy dissipation. A demonstration is performed utilizing the shear operating mode of the MRF and the one-way effect of the SMA. The damping performance of different MRF-SMA configurations is investigated and the corresponding energy consumption is evaluated. We demonstrate that the operation of MRF and SMA dampers complement each other, compensating for each other's weaknesses. In particular, the slow response from the MR damper is compensated by passive SMA damping using the pseudoplastic effect of martensite reorientation, which can dissipate a significant amount of shock energy at the beginning of the shock occurrence. The MR damper compensates for the incapability of the SMA to dampen subsequent vibrations as long as the magnetic field is applied. The presented hybrid SMA-MR damper demonstrates superior performance compared to individual dampers, allowing for up to five-fold reduction in energy consumption of the MR damper alone and thereby opening up the possibility of reducing the construction volume of the MR damper.

In this paper, we propose a path-planning problem for stereotactic neurosurgery using concentric tube robots. The main goal is to reach a given region of interest inside the brain, e.g. a tumor, starting from a feasible point on the skull with an ideally short path avoiding certain sensitive brain areas. To describe the shape of the entire cannula from an entry point to the point of interest we use an existing mechanical model for continuum robots. We show numerically that our approach enables the surgeon to reach areas within the brain that would be impossible with a straight cannula as it is currently state of the art.

A vibration control concept based on vibration energy conversion and storage with respect to a serial-stiffness-switch system (4S) has previously been proposed. Here, we first present a rotational electromagnetic serial-stiffness-switch system as a novel practical vibration control system for experimental validation of the concept and, furthermore, an improved control strategy for higher vibration suppression performance is also proposed. The system consists of two spring-switch elements in series, where a parallel switch can block a spring. As an alternating mechanical switch, the experimental system uses two electromagnets with a shared armature. By connecting the armature to the rotating load or the base, the electromagnets decide which of the two spiral springs is blocked, while the other is active. A switching law based on the rotation velocity of the payload is used. Modelling and building of the experimental system were carried out. The corresponding experiment and simulation were executed and they matched well. These results prove that our serial-stiffness-switch system is capable of converting vibration energy and realizing vibration reduction under a forced harmonic disturbance. The effects of disturbance frequency, disturbance amplitude and sampling frequency on the system performance are shown as well. A position feedback control-based switching law is further put forward and experimentally verified to improve the repositioning accuracy of the disturbed system.

A novel semi-active vibration control concept with a serial-switch-stiffness-system was previously presented in our work. Differing from conventional vibration control systems, this system does not dissipate but converts vibration energy as potential energy stored in springs and then reacts against external disturbance. As a piecewise linear system, whether or not energy conversion limit happens is an interesting nonlinear dynamic issue related to the systems steady state response. This paper formulates this issue in depth using the approach called equivalence in control. The systems control force represented by the converted vibration energy is approximately decomposed into two portions. One is responsible for low-frequency free response and the other for high-frequency switching response. An equivalent linear system suffering from a decomposed high-frequency switching force is obtained instead of the original switched system. The steady state response of the disturbed system can be delivered through linear superposition as executed in a linear system. Energy conversion limit occurring in the system under a harmonic disturbance is numerically shown by means of fast Fourier transformation. Analytical formulation and numerical simulation for open- and closed-loop control of the system are further carried out, respectively. The results give that the proposed approach is capable of solving the stead state response of the switched system accurately, and meanwhile, energy conversion limit occurs in the vibration control system indeed. Experimental discussion is also executed.

Varying compliance (VC) is an unavoidable form of parametric excitation in rolling bearings and can affect the stability and safety of the bearing and its supporting rotor system. To date, we have investigated VC primary resonance in ball bearings, and in this paper other parametric VC resonance types are addressed. For a classical ball bearing model with Hertzian contact and clearance nonlinearities between the rolling elements and raceway, the harmonic balance and alternating frequency/time domain (HB-AFT) method and Floquet theory are adopted to analyze the VC parametric resonances and their stabilities. It is found that the 1/2-order subharmonic resonances, 2-order superharmonic resonances, and various VC combination resonances, such as the 1-order and 2-order summed types, can be excited, thus resulting in period-1, period-2, period-4, period-8, period-35, quasi-period, and even chaotic VC motions in the system. Furthermore, the bifurcation and hysteresis characteristics of complex VC resonant responses are discussed, in which cyclic fold, period doubling, and the second Hopf bifurcation can occur. Finally, the global involution of VC resonances around bearing clearance-free operations (i.e., adjusting the bearing clearance to zero or one with low interference) are provided. The overall results extend the investigation of VC parametric resonance cases in rolling bearings.

In this study, a new class of magnetorheological (MR) damper, which can realize desired damping force at both low and high speeds of vehicle suspension systems, is proposed and its salient characteristics are shown through computer simulations. Unlike conventional MR dampers, the proposed MR damper has a specific pole shape function and therefore the damping coefficient is changed by varying the effective area of the main orifice. In addition, by controlling the opening or closing the bypass orifice, the drastic change of the damping coefficient is realizable. After briefly describing the operating principle, a mathematical modeling is performed considering the pole shape function which is a key feature of the proposed MR damper. Then, the field-dependent damping force and piston velocity-dependent characteristics are presented followed by an example on how to achieve desired damping force characteristics by changing the damping coefficient and slope breaking point which represents the bilinear damping property.

Estimation of functional parameters such as absolute torque, torque ripple or axial forces, are of great interest whilst the design process of a switched reluctance motor drive (SRM). Especially the axial construction form was not studied in detail in the past. This paper describes the results and procedure of the so called quasi transient simulation of an SRM, which is based on a nonlinear-magnetic, full field, time efficient and accurate finite element simulation (FEM).

A peristaltically actuated device, PADeMIS, composed of silicone rubber (SR) is under development for use in minimally invasive surgery. During locomotion, the device will be subject to a few thousand load changes involving varying, sometimes high, strains. The design is being optimised by finite element analysis, for which a constitutive law for the mechnical behaviour of silicone rubber is required. Uniaxial and biaxial tension tests have been performed on specimens of used silicon rubber. Synchronous fittign of uniaxial and biaxial tensile data gives significantly better results than using uniaxial or biaxial results alone to derive constitutve laws. The mechnical properties of SR were found to change from loading to loading up to few thousand cycles. Hence, simulating the deformation of SR structures is problematic. Furthermore, variability was observed between batches of SR.