Transiente Kalibrierung der Temperaturabhängigkeit resistiver Hochdrucksensoren in Großserie. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 12, S. 712-720
http://dx.doi.org/10.1515/teme-2016-0024
Challenges and trends in manufacturing measurement technology - the "Industrie 4.0" concept. - In: Journal of sensors and sensor systems, ISSN 2194-878X, Bd. 5 (2016), 2, S. 325-335
Strategic considerations and publications dealing with the future of industrial production are significantly influenced these days by the concept of "Industrie 4.0". For this reason the field of measurement technology for industrial production must also tackle this concept when thinking about future trends and challenges in metrology. To this end, the Manufacturing Metrology Roadmap 2020 of the VDI/VDE Society for Measurement and Automatic Control (GMA) was published in 2011 (VDI/VDE-GMA, 2011; Imkamp et al., 2012). The content of this roadmap is reviewed and extended here, covering new developments in the field of the Industrie 4.0 concept and presented with expanded and updated content.
http://dx.doi.org/10.5194/jsss-5-325-2016
Influence of the flow profile to Lorentz force velocimetry for weakly conducting fluids - an experimental validation. - In: Measurement science and technology, ISSN 1361-6501, Bd. 27 (2016), 12, S. 125306, insges. 9 S.
The Lorentz force velocimetry (LFV) is a highly feasible contactless method for measuring flow rate in a pipe or in a channel. This method has been established for liquid metal flows but also for weakly conducting electrolytes where the Lorentz force amplitudes are typically six orders smaller than the ones from liquid metal flows. Due to an increased resolution of the Lorentz force measurements which was the main focus of research in the last years, now it is possible to investigate the influence of the flow profile on the amplitude of the Lorentz force. Even if there is a semi-theoretical approach an experimental validation is still outstanding. Therefore we have tested symmetric and asymmetric flow profiles to test the LFV for weakly conducting fluids for typical industrial flows. Salt water has been used as a test electrolyte with constant values of the electrical conductivity from 0.035 to 20 S m-1 and of the flow velocity in a range of 0.5-3 m s-1. We confirmed by extensive measurements that LFV is a suitable method for flow measurements even for different flow profiles within 5% measurement uncertainty. For a wide range of applications in research and industry the LFV should be not sensitive to various flow profiles.
http://dx.doi.org/10.1088/0957-0233/27/12/125306
A signal interpolation method for Fabry-Perot interferometer utilized in mechanical vibration measurement. - In: Measurement, Bd. 92 (2016), S. 83-88
http://dx.doi.org/10.1016/j.measurement.2016.05.072
Nanopositioning and nanomeasuring machine NPMM-200 - a new powerful tool for large-range micro- and nanotechnology. - In: Surface topography, ISSN 2051-672X, Bd. 4 (2016), 3, S. 034004, insges. 8 S.
https://doi.org/10.1088/2051-672X/4/3/034004
Mehrkomponenten-Kraft- und -Drehmomentsensor nach dem Prinzip der elektromagnetischen Kompensation. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 7/8, S. 445-452
http://dx.doi.org/10.1515/teme-2015-0088
Dynamic characterization of a three-component force sensor using a Lorentz force load changer :
Dynamische Charakterisierung eines Dreikomponenten Kraftsensors mit Hilfe eines Lorentzkraft-Lastwechslers. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 7/8, S. 430-438
http://dx.doi.org/10.1515/teme-2015-0089
Dynamisches Verhalten von Berührungsthermometern unter Berücksichtigung der Temperaturabhängigkeit der Materialdaten - Erweiterung der VDI/VDE-Richtlinie 3522. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 7/8, S. 402-409
http://dx.doi.org/10.1515/teme-2015-0068
Kalibrierung von Wärmestromsensoren zur Detektion von kleinen Wärmeströmen. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 7/8, S. 393-401
http://dx.doi.org/10.1515/teme-2015-0016
Measurement uncertainty consideration in the case of precision length measurement applications. - In: Technisches Messen, ISSN 2196-7113, Bd. 83 (2016), 7/8, S. 453-458
http://dx.doi.org/10.1515/teme-2015-0035